Cannot boot red LED only

Post Reply
pearsomark
Posts: 1
Joined: Wed Sep 19, 2018 8:03 pm
languages_spoken: english
ODROIDs: 1 x HC2
1 x UX4
2 x C2
Contact:

Cannot boot red LED only

Unread post by pearsomark » Wed Sep 19, 2018 8:20 pm

Hello,

I recently bought a new C2 to add to my existing C2 Volumio. The new board only shows a red LED and does not boot using the same supply and sd card that works in my current C2.
UART output:
GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:1;EMMC:800;NAND:81;SD:0;READ:0;CH
K:F3;USB:8;LOOP:2;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;LOOP:3;EMMC:800;NAND:81;SD:0;READ:0;CHK:F3;USB:8;

I also tried an eMMC from my UX4 with the same result.

Is there anything else I can try?

Mark

User avatar
tobetter
Posts: 2581
Joined: Mon Feb 25, 2013 10:55 am
languages_spoken: Korean, English
ODROIDs: X, X2, U2, U3, XU3, C1
Location: Paju, South Korea
Contact:

Re: Cannot boot red LED only

Unread post by tobetter » Wed Sep 19, 2018 11:40 pm

Hi,
What you should do is to try another memory card or eMMC just in case if your C2 can boot, and check PSU if it supplys proper voltage. If the same output comes, according to the log, your ODROID does not fetch the boot loader from either SD card and eMMC.

meguerche
Posts: 1
Joined: Sun Dec 02, 2018 1:10 pm
languages_spoken: portuguese, english
ODROIDs: C2
Contact:

Cannot boot red LED only

Unread post by meguerche » Sun Dec 02, 2018 2:03 pm

Last month my C2 board got in same behavior, red light only and it does not boot, I usually used it with eMMC and external power suply 5V2A through round pin DC input, OTG Power Jumper opened.

After crash I flashed OS on eMMC again, also tried 3 others microSD cards, power source was changed to a SAMSUNG 5V 2A (Galaxy Tab Pro) connected to USB OTG port (Jumper Closed) and in all tries I got similar results.

Power on plugged eMMC and no microSD

Code: Select all

GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
TE: 214367
no sdio debug board detected

BL2 Built : 11:44:26, Nov 25 2015.
gxb gfb13a3b-c2 - jcao@wonton

Board ID = 8
set vcck to 1100 mv
set vddee to 1050 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same


Power on plugged microSD and no eMMC

Code: Select all

GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:0;
TE: 176731
no sdio debug board detected

BL2 Built : 11:44:26, Nov 25 2015.
gxb gfb13a3b-c2 - jcao@wonton

Board ID = 8
set vcck to 1100 mv
set vddee to 1050 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same
PS:
I have used a USB power meter and I got 5.2V 0.42A, that looks like ok while this is same I got in time it was working well, no external periferals, CPU idle of course.

User avatar
tobetter
Posts: 2581
Joined: Mon Feb 25, 2013 10:55 am
languages_spoken: Korean, English
ODROIDs: X, X2, U2, U3, XU3, C1
Location: Paju, South Korea
Contact:

Re: Cannot boot red LED only

Unread post by tobetter » Mon Dec 03, 2018 10:36 am

meguerche wrote:Last month my C2 board got in same behavior, red light only and it does not boot, I usually used it with eMMC and external power suply 5V2A through round pin DC input, OTG Power Jumper opened.

After crash I flashed OS on eMMC again, also tried 3 others microSD cards, power source was changed to a SAMSUNG 5V 2A (Galaxy Tab Pro) connected to USB OTG port (Jumper Closed) and in all tries I got similar results.

Power on plugged eMMC and no microSD

Code: Select all

GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:0;READ:0;CHK:0;
TE: 214367
no sdio debug board detected

BL2 Built : 11:44:26, Nov 25 2015.
gxb gfb13a3b-c2 - jcao@wonton

Board ID = 8
set vcck to 1100 mv
set vddee to 1050 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same


Power on plugged microSD and no eMMC

Code: Select all

GXBB:BL1:08dafd:0a8993;FEAT:EDFC318C;POC:3;RCY:0;EMMC:800;NAND:81;SD:0;READ:0;CHK:0;
TE: 176731
no sdio debug board detected

BL2 Built : 11:44:26, Nov 25 2015.
gxb gfb13a3b-c2 - jcao@wonton

Board ID = 8
set vcck to 1100 mv
set vddee to 1050 mv
CPU clk: 1536MHz
DDR channel setting: DDR0 Rank0+1 same
PS:
I have used a USB power meter and I got 5.2V 0.42A, that looks like ok while this is same I got in time it was working well, no external periferals, CPU idle of course.
Don't you have any other logs after DDR channel setting: DDR0 Rank0+1 same? If any, please share more logs...

Post Reply

Return to “Issues”

Who is online

Users browsing this forum: No registered users and 0 guests