hc-1 faulty..??

Post Reply
phaseshifter
Posts: 3014
Joined: Fri May 08, 2015 9:12 am
languages_spoken: english
ODROIDs: N-1..c1+ ..c-2..xu3 lite,xu4...u-3..
u-2...other odroid acc`s as well
Contact:

hc-1 faulty..??

Unread post by phaseshifter » Fri Jun 01, 2018 2:22 pm

so i have not used my hc-1 for quite some time as i had to use it to help a user establish weather his hardware was or is faulty..but when i use 16.04.4 minimal or any ubuntu image
and establish it`s param`s in /etc/fstab..
the board once booted via the uart goes into maintenance mode so i input the password and am able to work with the file system..if you are trying to do this via ssh forget it ..you need the uart kit..

Code: Select all

Give root password for maintenance
(or press Control-D to continue): 
 
so i am guessing something has faulted in the hard ware some how.

Code: Select all

lsusb
shows this with no drive connected

Code: Select all

root@odroid:~# lsusb
Bus 006 Device 002: ID 0bda:8153 Realtek Semiconductor Corp. 
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@odroid:~# 

Code: Select all

lsusb -t
shows this

Code: Select all

root@odroid:~# lsusb -t
/:  Bus 06.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M             
    |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M   
/:  Bus 05.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M              
/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M             
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M              
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=exynos-ohci/3p, 12M            
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=exynos-ehci/3p, 480M           
root@odroid:~# 
as it boot`s up it also takes 1mim30sec for a start job to run with the hdd connected...

Code: Select all

lsusb 
with hdd connected shows this

Code: Select all

root@odroid:~# lsusb                                                            
Bus 006 Device 002: ID 0bda:8153 Realtek Semiconductor Corp.                    
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub                  
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub                  
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub                  
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub                  
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub                  
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub                  
root@odroid:~# 

Code: Select all

lsusb -t
shows this with hdd connected..

Code: Select all

root@odroid:~# lsusb -t                                                         
/:  Bus 06.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M             
    |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M   
/:  Bus 05.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M              
/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M             
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M              
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=exynos-ohci/3p, 12M            
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=exynos-ehci/3p, 480M           
root@odroid:~# 

so i am wondering if somehow my usb buss for the hdd is at fault ..no matter how i establish "fstab" for any drive or any partition type ..it still fails going in to maintenance mode

it never finds the drive..
Build It And They Will Come...Be Bold And Mighty Forces Will Come To Your Aid..!!!

User avatar
odroid
Site Admin
Posts: 29408
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID
Contact:

Re: hc-1 faulty..??

Unread post by odroid » Fri Jun 01, 2018 4:41 pm

If the HDD is not connected or dead, the SATA bridge controller doesn't work.
So you have to check the HDD functionality with other system first.

phaseshifter
Posts: 3014
Joined: Fri May 08, 2015 9:12 am
languages_spoken: english
ODROIDs: N-1..c1+ ..c-2..xu3 lite,xu4...u-3..
u-2...other odroid acc`s as well
Contact:

Re: hc-1 faulty..??

Unread post by phaseshifter » Fri Jun 01, 2018 5:18 pm

the hdd works on other systems..also i have tried a few of them..

on the hc-1..the board boot`s fine if i do not define the hdd in the fstab file

Code: Select all

/dev/sda1  /media/hdd1 ntfs defaults 0 1
this is what i have added to the fstab file above code
i made a mount point for the hdd

Code: Select all

sudo mkdir -p /media/hdd1
also the green hdd led is lit it flashes once at start up then remains lit weather there is a drive connected or not..??
Build It And They Will Come...Be Bold And Mighty Forces Will Come To Your Aid..!!!

User avatar
odroid
Site Admin
Posts: 29408
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID
Contact:

Re: hc-1 faulty..??

Unread post by odroid » Fri Jun 01, 2018 5:49 pm

When I connected a SATA storage to HC1/HC2, JMS578 detected well.

Code: Select all

root@odroid:~# lsusb
Bus 006 Device 002: ID 0bda:8153 Realtek Semiconductor Corp. 
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 002: ID 152d:0578 JMicron Technology Corp. / JMicron USA Technology Corp. 
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
root@odroid:~# lsusb -t
/:  Bus 06.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M
    |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M
/:  Bus 05.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M
/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M
    |__ Port 1: Dev 2, If 0, Class=Mass Storage, Driver=uas, 5000M
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=exynos-ohci/3p, 12M
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=exynos-ehci/3p, 480M
If I don't connect a storage, JMS578 doesn't exist in lsusb output.

Code: Select all

root@odroid:~# lsusb                                                                                                                                              
Bus 006 Device 002: ID 0bda:8153 Realtek Semiconductor Corp.                                                                                                      
Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub                                                                                                    
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub                                                                                                    
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub                                                                                                    
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub                                                                                                    
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub                                                                                                    
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub                                                                                                    
root@odroid:~# lsusb -t                                                                                                                                           
/:  Bus 06.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M                                                                                               
    |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M                                                                                     
/:  Bus 05.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M                                                                                                
/:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 5000M                                                                                               
/:  Bus 03.Port 1: Dev 1, Class=root_hub, Driver=xhci-hcd/1p, 480M                                                                                                
/:  Bus 02.Port 1: Dev 1, Class=root_hub, Driver=exynos-ohci/3p, 12M                                                                                              
/:  Bus 01.Port 1: Dev 1, Class=root_hub, Driver=exynos-ehci/3p, 480M 
SATA LED is always on after booting regardlress of the SATA storage connection.

phaseshifter
Posts: 3014
Joined: Fri May 08, 2015 9:12 am
languages_spoken: english
ODROIDs: N-1..c1+ ..c-2..xu3 lite,xu4...u-3..
u-2...other odroid acc`s as well
Contact:

Re: hc-1 faulty..??

Unread post by phaseshifter » Fri Jun 01, 2018 6:24 pm

Hmmm ok well i am not seeing the JMS578 at all when any drive is attached..
i thought something was wrong ..but been a while since i have used my hc-1..

so i guess that there is a problem ...

i have tried 3 hdd`s 2 ssd`s and a 500Gb wd spinner...none show up the jms578

i guess well that it is broken in some way

i also connected a usb external ssd to the usb 2 port
it had issues reading and writing to that drive as well
so i guess the problem remain`s to be seen as to what exactly is damaged on my hc-1
Build It And They Will Come...Be Bold And Mighty Forces Will Come To Your Aid..!!!

User avatar
odroid
Site Admin
Posts: 29408
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID
Contact:

Re: hc-1 faulty..??

Unread post by odroid » Fri Jun 01, 2018 6:49 pm

I think your HC1 seemed to be damaged by unknown electrical shock.
Did you try our official 5V/4A or 5V/6A PSU?

phaseshifter
Posts: 3014
Joined: Fri May 08, 2015 9:12 am
languages_spoken: english
ODROIDs: N-1..c1+ ..c-2..xu3 lite,xu4...u-3..
u-2...other odroid acc`s as well
Contact:

Re: hc-1 faulty..??

Unread post by phaseshifter » Fri Jun 01, 2018 6:54 pm

i am using an original 4 amp 5 volt xu4 power pack

the hc-1 was working last time i used it..i`ll purchase another thank`s
Build It And They Will Come...Be Bold And Mighty Forces Will Come To Your Aid..!!!

Post Reply

Return to “Issues”

Who is online

Users browsing this forum: No registered users and 2 guests