[SOLVED] Odroid-XU4 won't boot

[akhilkalwakurthy]

My XU4 will not boot. It was working before it froze. I've rebooted it and from then, it is in a reboot loop.
I've tried different sd-cards and os builds (ubuntu, arch, omv, android). Red LED stays on, blue LED stays on for a few seconds, then blinks a couple of times and reboots. I'm using the official 5V/4A power supply. Only an ethernet cable is connected.
Serial logs from official Ubuntu image (ubuntu-18.04.3-4.14-minimal-odroid-xu4-20190910.img) shows kernel booting fine. It reboots trying to start systemd (the last line from serial logs...). Here is the serial log

Code: Select all

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 4.14.141-169 (root@1604_builder_armhf) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Sat Aug 31 23:19:59 -03 2019
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel Odroid XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0xb6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] Running under secure firmware.
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x420 with crng_init=0
[    0.000000] percpu: Embedded 17 pages/cpu s37452 r8192 d23988 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC0,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false s5p_mfc.mem=16M
[    0.000000] hdmi: using HDMI mode
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1902216K/2074624K available (8192K kernel code, 656K rwdata, 2352K rodata, 1024K init, 318K bss, 41336K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0da42e0   ( 657 kB)
[    0.000000]        .bss : 0xc0dac378 - 0xc0dfbea0   ( 319 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] hperf_hmp: fast CPUs mask: 000000F0
[    0.000000] hperf_hmp: slow CPUs mask: 0000000F
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000007] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000030] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 49
[    0.001603] Console: colour dummy device 80x30
[    0.002277] console [tty1] enabled
[    0.002319] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002360] pid_max: default: 32768 minimum: 301
[    0.002550] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002589] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003454] CPU: Testing write buffer coherency: ok
[    0.004373] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.020047] Setting up static identity map for 0x40100000 - 0x40100060
[    0.020666] ARM CCI driver probed
[    0.020904] Exynos MCPM support installed
[    0.027989] Hierarchical SRCU implementation.
[    0.043989] smp: Bringing up secondary CPUs ...
[    0.072371] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.096327] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.124323] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.152324] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.152333] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.172321] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.172328] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.180621] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.180627] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.188629] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.188636] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.188890] smp: Brought up 1 node, 8 CPUs
[    0.188938] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.188960] CPU: All CPU(s) started in HYP mode.
[    0.188979] CPU: Virtualization extensions available.
[    0.190835] devtmpfs: initialized
[    0.208177] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.208375] hperf_hmp: registered cpufreq transition notifier
[    0.208562] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.208598] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.211401] pinctrl core: initialized pinctrl subsystem
[    0.213572] NET: Registered protocol family 16
[    0.218366] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.224431] cpuidle: using governor menu
[    0.225241] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.225269] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.233733] exynos-audss-clk 3810000.audss-clock-controller: epll 180633609
[    0.256389] EXYNOS5420 PMU initialized
[    0.299387] usbcore: registered new interface driver usbfs
[    0.299456] usbcore: registered new interface driver hub
[    0.299606] usbcore: registered new device driver usb
[    0.300054] i2c-gpio soc:i2c-hdmi: using pins 177 (SDA) and 178 (SCL)
[    0.300664] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.300691] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.300915] s3c-i2c 12c70000.i2c: i2c-1: S3C I2C adapter
[    0.301432] media: Linux media interface: v0.10
[    0.301487] Linux video capture interface: v2.00
[    0.301601] pps_core: LinuxPPS API ver. 1 registered
[    0.301620] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.301890] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    0.302736] Advanced Linux Sound Architecture Driver Initialized.
[    0.303958] clocksource: Switched to clocksource mct-frc
[    0.364595] VFS: Disk quotas dquot_6.6.0
[    0.364678] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.378410] NET: Registered protocol family 2
[    0.378984] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.379082] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.379250] TCP: Hash tables configured (established 8192 bind 8192)
[    0.379365] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.379416] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.379627] NET: Registered protocol family 1
[    0.380347] RPC: Registered named UNIX socket transport module.
[    0.380370] RPC: Registered udp transport module.
[    0.380388] RPC: Registered tcp transport module.
[    0.380406] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.380614] Trying to unpack rootfs image as initramfs...
[    0.667977] random: fast init done
[    0.838363] Freeing initrd memory: 8124K
[    0.839828] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.840886] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.844407] audit: initializing netlink subsys (disabled)
[    0.844632] audit: type=2000 audit(0.840:1): state=initialized audit_enabled=0 res=1
[    0.845187] Initialise system trusted keyrings
[    0.845375] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.852666] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.853528] NFS: Registering the id_resolver key type
[    0.853562] Key type id_resolver registered
[    0.853581] Key type id_legacy registered
[    0.853610] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.853661] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.858537] Key type asymmetric registered
[    0.858559] Asymmetric key parser 'x509' registered
[    0.858624] bounce: pool size: 64 pages
[    0.858687] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    0.858907] io scheduler noop registered
[    0.858929] io scheduler deadline registered
[    0.859089] io scheduler cfq registered (default)
[    0.859110] io scheduler mq-deadline registered
[    0.859129] io scheduler kyber registered
[    0.859383] io scheduler bfq registered
[    0.861860] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator
[    0.862851] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator
[    0.862937] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator
[    0.863331] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus not found, using dummy regulator
[    0.863414] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus-boost not found, using dummy regulator
[    0.868455] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330
[    0.868482] dma-pl330 3880000.adma: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.871056] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330
[    0.871082] dma-pl330 121a0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.873696] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330
[    0.873722] dma-pl330 121b0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.874561] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330
[    0.874587] dma-pl330 10800000.mdma: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.940392] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.942723] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 58, base_baud = 0) is a S3C6400/10
[    1.841375] console [ttySAC0] enabled
[    1.845371] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 59, base_baud = 0) is a S3C6400/10
[    1.854213] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 60, base_baud = 0) is a S3C6400/10
[    1.863047] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
[    1.873745] exynos-mixer 14450000.mixer: Linked as a consumer to 14650000.sysmmu
[    1.878938] iommu: Adding device 14450000.mixer to group 0
[    1.886012] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd': -517
[    1.891632] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a60000.sysmmu
[    1.898409] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a70000.sysmmu
[    1.905715] iommu: Adding device 10850000.g2d to group 1
[    1.911317] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully probed.
[    1.919983] exynos-rot 11c00000.rotator: Linked as a consumer to 11d40000.sysmmu
[    1.926244] iommu: Adding device 11c00000.rotator to group 2
[    1.932238] exynos-rot 11c00000.rotator: The exynos rotator is probed successfully
[    1.940269] exynos-drm-ipp exynos-drm-ipp: drm ipp registered successfully.
[    1.950662] mali 11800000.mali: Continuing without Mali regulator control
[    1.953828] mali 11800000.mali: GPU identified as 0x0620 r0p1 status 0
[    1.960100] mali 11800000.mali: Protected mode not available
[    1.965619] devfreq devfreq0: Couldn't update frequency transition information.
[    1.973187] mali 11800000.mali: Probed as mali0
[    1.986748] brd: module loaded
[    1.987467] libphy: Fixed MDIO Bus: probed
[    1.987915] usbcore: registered new interface driver r8152
[    1.989583] usbcore: registered new interface driver cdc_ether
[    1.995377] usbcore: registered new interface driver cdc_subset
[    2.003352] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.007756] ehci-exynos: EHCI EXYNOS driver
[    2.012273] exynos-ehci 12110000.usb: EHCI Host Controller
[    2.017371] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    2.025248] exynos-ehci 12110000.usb: irq 80, io mem 0x12110000
[    2.044009] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    2.044432] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.044586] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.050805] usb usb1: Product: EHCI Host Controller
[    2.055653] usb usb1: Manufacturer: Linux 4.14.141-169 ehci_hcd
[    2.061543] usb usb1: SerialNumber: 12110000.usb
[    2.066699] hub 1-0:1.0: USB hub found
[    2.069901] hub 1-0:1.0: 3 ports detected
[    2.074802] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.080045] ohci-exynos: OHCI EXYNOS driver
[    2.084374] exynos-ohci 12120000.usb: USB Host Controller
[    2.089554] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    2.097263] exynos-ohci 12120000.usb: irq 80, io mem 0x12120000
[    2.164242] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.164396] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.164558] usb usb2: Product: USB Host Controller
[    2.164669] usb usb2: Manufacturer: Linux 4.14.141-169 ohci_hcd
[    2.166604] usb usb2: SerialNumber: 12120000.usb
[    2.171753] hub 2-0:1.0: USB hub found
[    2.174997] hub 2-0:1.0: 3 ports detected
[    2.182144] mousedev: PS/2 mouse device common for all mice
[    2.185767] i2c /dev entries driver
[    2.203686] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    2.221797] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.240557] vdd_ldo30: Bringing 1800000uV into 3300000-3300000uV
[    2.268851] vdd_1.8v_ldo: Bringing 1850000uV into 1500000-1500000uV
[    3.311171] s5m-rtc s2mps14-rtc: rtc core: registered s5m-rtc as rtc0
[    3.315332] s5p-jpeg 11f50000.jpeg: Linked as a consumer to 11f10000.sysmmu
[    3.315543] iommu: Adding device 11f50000.jpeg to group 3
[    3.316070] s5p-jpeg 11f50000.jpeg: encoder device registered as /dev/video30
[    3.316400] s5p-jpeg 11f50000.jpeg: decoder device registered as /dev/video31
[    3.321890] s5p-jpeg 11f50000.jpeg: Samsung S5P JPEG codec
[    3.327564] s5p-jpeg 11f60000.jpeg: Linked as a consumer to 11f20000.sysmmu
[    3.334337] iommu: Adding device 11f60000.jpeg to group 4
[    3.340060] s5p-jpeg 11f60000.jpeg: encoder device registered as /dev/video32
[    3.346935] s5p-jpeg 11f60000.jpeg: decoder device registered as /dev/video33
[    3.353865] s5p-jpeg 11f60000.jpeg: Samsung S5P JPEG codec
[    3.360476] s5p-mfc 11000000.codec: Linked as a consumer to 11200000.sysmmu
[    3.366391] s5p-mfc 11000000.codec: Linked as a consumer to 11210000.sysmmu
[    3.373247] iommu: Adding device 11000000.codec to group 5
[    3.396529] s5p-mfc 11000000.codec: preallocated 16 MiB buffer for the firmware and context buffers
[    3.396839] (NULL device *): Direct firmware load for s5p-mfc-v8.fw failed with error -2
[    3.397022] s5p_mfc_load_firmware:73: Firmware is not present in the /lib/firmware directory nor compiled in kernel
[    3.406319] s5p-mfc 11000000.codec: decoder registered as /dev/video10
[    3.412773] s5p-mfc 11000000.codec: encoder registered as /dev/video11
[    3.420907] exynos-gsc 13e00000.video-scaler: Linked as a consumer to 13e80000.sysmmu
[    3.426976] iommu: Adding device 13e00000.video-scaler to group 6
[    3.434258] exynos-gsc 13e10000.video-scaler: Linked as a consumer to 13e90000.sysmmu
[    3.440831] iommu: Adding device 13e10000.video-scaler to group 7
[    3.466777] thermal thermal_zone0: failed to read out thermal zone (-22)
[    3.467843] thermal thermal_zone1: failed to read out thermal zone (-22)
[    3.468967] thermal thermal_zone2: failed to read out thermal zone (-22)
[    3.470059] thermal thermal_zone3: failed to read out thermal zone (-22)
[    3.474485] thermal thermal_zone4: failed to read out thermal zone (-22)
[    3.480963] device-mapper: uevent: version 1.0.3
[    3.485127] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[    3.507571] sdhci: Secure Digital Host Controller Interface driver
[    3.507697] sdhci: Copyright(c) Pierre Ossman
[    3.508020] Synopsys Designware Multimedia Card Interface Driver
[    3.510226] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    3.516574] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    3.522913] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    3.528306] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 83,64 bit host data width,64 deep fifo
[    3.537700] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    3.564438] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.584338] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    3.584521] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    3.584653] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    3.584808] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 84,64 bit host data width,64 deep fifo
[    3.612435] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.633064] ledtrig-cpu: registered to indicate activity on CPUs
[    3.633948] s5p-secss 10830000.sss: s5p-sss driver registered
[    3.634475] hidraw: raw HID events driver (C) Jiri Kosina
[    3.645431] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    3.645667] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    3.645902] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    3.647742] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    3.658410] NET: Registered protocol family 17
[    3.658656] NET: Registered protocol family 15
[    3.663128] Key type dns_resolver registered
[    3.667731] Registering SWP/SWPB emulation handler
[    3.672446] registered taskstats version 1
[    3.676172] Loading compiled-in X.509 certificates
[    3.686368] Key type encrypted registered
[    3.705081] OF: graph: no port node found in /soc/hdmi@14530000
[    3.706073] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[    3.706356] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0966344)
[    3.706498] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc09669e4)
[    3.711791] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.718369] [drm] No driver support for vblank timestamp query.
[    3.724382] [drm] Cannot find any crtc or sizes
[    3.729196] [drm] Initialized exynos 1.0.0 20110530 for exynos-drm on minor 0
[    3.736157] [drm] Cannot find any crtc or sizes
[    3.741940] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    3.745853] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 3
[    3.753689] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.762862] xhci-hcd xhci-hcd.3.auto: irq 149, io mem 0x12000000
[    3.768936] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    3.775560] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.782755] usb usb3: Product: xHCI Host Controller
[    3.787604] usb usb3: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    3.793495] usb usb3: SerialNumber: xhci-hcd.3.auto
[    3.798661] hub 3-0:1.0: USB hub found
[    3.802098] hub 3-0:1.0: 1 port detected
[    3.806169] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    3.811440] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 4
[    3.819074] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0  SuperSpeed
[    3.825701] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.833802] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    3.840470] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.847656] usb usb4: Product: xHCI Host Controller
[    3.849500] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    3.852515] usb usb4: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    3.863653] mmc1: new ultra high speed DDR50 SDHC card at address aaaa
[    3.868113] usb usb4: SerialNumber: xhci-hcd.3.auto
[    3.875513] mmcblk1: mmc1:aaaa SS16G 14.8 GiB 
[    3.880336] hub 4-0:1.0: USB hub found
[    3.887626] hub 4-0:1.0: 1 port detected
[    3.893712] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    3.896700]  mmcblk1: p1 p2
[    3.896999] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 5
[    3.907605] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.916758] xhci-hcd xhci-hcd.6.auto: irq 150, io mem 0x12400000
[    3.922837] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    3.929459] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.936658] usb usb5: Product: xHCI Host Controller
[    3.941504] usb usb5: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    3.947396] usb usb5: SerialNumber: xhci-hcd.6.auto
[    3.952527] hub 5-0:1.0: USB hub found
[    3.956000] hub 5-0:1.0: 1 port detected
[    3.960075] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    3.965340] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 6
[    3.972963] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0  SuperSpeed
[    3.979609] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.987699] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[    3.994364] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.001555] usb usb6: Product: xHCI Host Controller
[    4.006407] usb usb6: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    4.012299] usb usb6: SerialNumber: xhci-hcd.6.auto
[    4.017437] hub 6-0:1.0: USB hub found
[    4.020898] hub 6-0:1.0: 1 port detected
[    4.025709] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[    4.030404] rtc rtc1: invalid alarm value: 1900-1-1 0:0:0
[    4.035796] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc1
[    4.042999] exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
[    4.050500] exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
[    4.058436] exynos-bus: new bus device registered: soc:bus_fsys_apb (200000 KHz ~ 200000 KHz)
[    4.066880] exynos-bus: new bus device registered: soc:bus_fsys (200000 KHz ~ 200000 KHz)
[    4.075150] exynos-bus: new bus device registered: soc:bus_fsys2 ( 75000 KHz ~ 150000 KHz)
[    4.083454] exynos-bus: new bus device registered: soc:bus_mfc ( 96000 KHz ~ 333000 KHz)
[    4.091480] exynos-bus: new bus device registered: soc:bus_gen ( 89000 KHz ~ 267000 KHz)
[    4.099458] exynos-bus: new bus device registered: soc:bus_peri ( 67000 KHz ~  67000 KHz)
[    4.107722] exynos-bus: new bus device registered: soc:bus_g2d ( 84000 KHz ~ 333000 KHz)
[    4.115739] exynos-bus: new bus device registered: soc:bus_g2d_acp ( 67000 KHz ~ 267000 KHz)
[    4.124174] exynos-bus: new bus device registered: soc:bus_jpeg ( 75000 KHz ~ 300000 KHz)
[    4.132326] exynos-bus: new bus device registered: soc:bus_jpeg_apb ( 84000 KHz ~ 167000 KHz)
[    4.140708] exynos-bus: new bus device registered: soc:bus_disp1_fimd (120000 KHz ~ 200000 KHz)
[    4.149418] exynos-bus: new bus device registered: soc:bus_disp1 (120000 KHz ~ 300000 KHz)
[    4.157644] exynos-bus: new bus device registered: soc:bus_gscl_scaler (150000 KHz ~ 300000 KHz)
[    4.166476] exynos-bus: new bus device registered: soc:bus_mscl ( 84000 KHz ~ 400000 KHz)
[    4.174522] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
[    4.182166] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
[    4.190673] odroid-audio sound: multicodec <-> 3830000.i2s mapping ok
[    4.199639] s5m-rtc s2mps14-rtc: setting system clock to 2000-01-01 00:00:11 UTC (946684811)
[    4.209751] ALSA device list:
[    4.209846]   #0: Odroid-XU4
[    4.211776] Freeing unused kernel memory: 1024K
Loading, please wait...
starting version 237

Please help!

[odroid]

According to your log, kernel booted well but it couldn't mount the root file system probably.
Did you try a UHS-1 microSD card?

Did you flash the OS images with Etcher? Don't extract .xz file when you use Etcher.
https://wiki.odroid.com/troubleshooting ... ing_etcher

[akhilkalwakurthy]

I've tried UHS-1 SD card as well, still no luck. I did flash the OS image using Etcher without extracting. I also tried arch (as per arch arm wiki), still no luck.
Unfortunately, I don't have a UART cable so, I'm using an arduino mega for UART from ttySAC0 connected to shifter shield at 5v. Log gets cutoff and it reboots.

Code: Select all

...
[    4.162441] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[    4.169342] s5m-rtc s2mps14-rtc: setting system clock to 2000-01-01 00:00:12 UTC (946684812)
[    4.180962] ALSA device list:
[    4.181057]   #0: Odroid-XU4
[    4.182514] Freeing unused kernel memory: 1024K
:: running early hook [udev]
Starting version 243.162-2-arch
:: running hook [udev]
:: Triggering uevents...
[    4.288146] usb 3-1: new high-speed USB⸮[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 4.14.150-1-ARCH (builduser@leming) (gcc version 8.3.0 (GCC)) #1 SMP PREEMPT Wed Oct 30 01:34:23 UTC 2019
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel Odroid XU4
[    0.000000] debug: ignoring loglevel setting.
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0xb6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] On node 0 totalpages: 518656
[    0.000000] free_area_init_node: node 0, pgdat c0e90700, node_mem_map eee25000
[    0.000000]   Normal zone: 1728 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000]   HighMem zone: 322048 pages, LIFO batch:31
[    0.000000] Running under secure firmware.
[    0.000000] random: get_random_bytes called from start_kernel+0x9c/0x444 with crng_init=0
[    0.000000] percpu: Embedded 17 pages/cpu s37452 r8192 d23988 u69632
[    0.000000] pcpu-alloc: s37452 r8192 d23988 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC0,115200n8 root=PARTUUID=ba9d65bc-01 rw rootwait smsc95xx.macaddr=  ignore_loglevel emergency s5p_mfc.mem=16M
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1902760K/2074624K available (9216K kernel code, 666K rwdata, 2420K rodata, 1024K init, 318K bss, 40792K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0a00000   (10208 kB)
[    0.000000]       .init : 0xc0d00000 - 0xc0e00000   (1024 kB)
[    0.000000]       .data : 0xc0e00000 - 0xc0ea6a80   ( 667 kB)
[    0.000000]        .bss : 0xc0eaef18 - 0xc0efea68   ( 319 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] hperf_hmp: fast CPUs mask: 000000F0
[    0.000000] hperf_hmp: slow CPUs mask: 0000000F
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000008] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000032] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 49
[    0.001614] Console: colour dummy device 80x30
[    0.002416] console [tty1] enabled
[    0.002459] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002501] pid_max: default: 32768 minimum: 301
[    0.002692] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002734] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003600] CPU: Testing write buffer coherency: ok
[    0.004514] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.020053] Setting up static identity map for 0x40100000 - 0x40100060
[    0.020676] ARM CCI driver probed
[    0.020913] Exynos MCPM support installed
[    0.027992] Hierarchical SRCU implementation.
[    0.043990] smp: Bringing up secondary CPUs ...
[    0.072373] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.096334] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.124328] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.152377] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.152385] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.172367] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.172375] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.180668] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.180675] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.188657] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.188664] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.188918] smp: Brought up 1 node, 8 CPUs
[    0.188965] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.188990] CPU: All CPU(s) started in HYP mode.
[    0.189009] CPU: Virtualization extensions available.
[    0.190861] devtmpfs: initialized
[    0.207567] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.207725] hperf_hmp: registered cpufreq transition notifier
[    0.207918] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.207954] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.210423] pinctrl core: initialized pinctrl subsystem
[    0.212595] NET: Registered protocol family 16
[    0.218421] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.224442] cpuidle: using governor menu
[    0.225208] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.225236] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.233752] exynos-audss-clk 3810000.audss-clock-controller: epll 180633609
[    0.256803] EXYNOS5420 PMU initialized
[    0.303415] SCSI subsystem initialized
[    0.303619] usbcore: registered new interface driver usbfs
[    0.303686] usbcore: registered new interface driver hub
[    0.303840] usbcore: registered new device driver usb
[    0.304288] i2c-gpio soc:i2c-hdmi: using pins 177 (SDA) and 178 (SCL)
[    0.304906] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.304934] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.305166] s3c-i2c 12c70000.i2c: i2c-1: S3C I2C adapter
[    0.305695] media: Linux media interface: v0.10
[    0.305745] Linux video capture interface: v2.00
[    0.306069] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    0.306935] Advanced Linux Sound Architecture Driver Initialized.
[    0.308110] clocksource: Switched to clocksource mct-frc
[    0.381407] VFS: Disk quotas dquot_6.6.0
[    0.381492] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.395378] NET: Registered protocol family 2
[    0.395970] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.396068] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.396282] TCP: Hash tables configured (established 8192 bind 8192)
[    0.396399] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.396450] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.396657] NET: Registered protocol family 1
[    0.397350] RPC: Registered named UNIX socket transport module.
[    0.397374] RPC: Registered udp transport module.
[    0.397392] RPC: Registered tcp transport module.
[    0.397410] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.397627] Trying to unpack rootfs image as initramfs...
[    0.668133] random: fast init done
[    0.775639] Freeing initrd memory: 6544K
[    0.777150] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.778243] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.781775] audit: initializing netlink subsys (disabled)
[    0.781974] audit: type=2000 audit(0.780:1): state=initialized audit_enabled=0 res=1
[    0.782548] Initialise system trusted keyrings
[    0.782760] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.789843] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.790704] NFS: Registering the id_resolver key type
[    0.790746] Key type id_resolver registered
[    0.790766] Key type id_legacy registered
[    0.790794] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.790846] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.795908] Key type asymmetric registered
[    0.795934] Asymmetric key parser 'x509' registered
[    0.796003] bounce: pool size: 64 pages
[    0.796065] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 246)
[    0.796329] io scheduler noop registered
[    0.796352] io scheduler deadline registered
[    0.796510] io scheduler cfq registered (default)
[    0.796532] io scheduler mq-deadline registered
[    0.796551] io scheduler kyber registered
[    0.796787] io scheduler bfq registered
[    0.799201] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator
[    0.800271] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator
[    0.800362] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator
[    0.800734] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus not found, using dummy regulator
[    0.800817] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus-boost not found, using dummy regulator
[    0.805800] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330
[    0.805828] dma-pl330 3880000.adma: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.808471] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330
[    0.808498] dma-pl330 121a0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.811122] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330
[    0.811149] dma-pl330 121b0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.811997] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330
[    0.812023] dma-pl330 10800000.mdma: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.877777] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.880173] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 58, base_baud = 0) is a S3C6400/10
[    1.800842] console [ttySAC0] enabled
[    1.804838] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 59, base_baud = 0) is a S3C6400/10
[    1.813681] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 60, base_baud = 0) is a S3C6400/10
[    1.822521] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
[    1.833231] exynos-mixer 14450000.mixer: Linked as a consumer to 14650000.sysmmu
[    1.838407] iommu: Adding device 14450000.mixer to group 0
[    1.845511] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd': -517
[    1.851109] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a60000.sysmmu
[    1.857878] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a70000.sysmmu
[    1.865187] iommu: Adding device 10850000.g2d to group 1
[    1.870789] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully probed.
[    1.879431] exynos-rot 11c00000.rotator: Linked as a consumer to 11d40000.sysmmu
[    1.885713] iommu: Adding device 11c00000.rotator to group 2
[    1.891676] exynos-rot 11c00000.rotator: The exynos rotator is probed successfully
[    1.899662] exynos-drm-ipp exynos-drm-ipp: drm ipp registered successfully.
[    1.910188] mali 11800000.mali: Continuing without Mali regulator control
[    1.913302] mali 11800000.mali: GPU identified as 0x0620 r0p1 status 0
[    1.919536] mali 11800000.mali: Protected mode not available
[    1.925092] devfreq devfreq0: Couldn't update frequency transition information.
[    1.932674] mali 11800000.mali: Probed as mali0
[    1.946435] brd: module loaded
[    1.947283] libphy: Fixed MDIO Bus: probed
[    1.947730] usbcore: registered new interface driver r8152
[    1.949048] usbcore: registered new interface driver cdc_ether
[    1.954847] usbcore: registered new interface driver cdc_subset
[    1.962843] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.967223] ehci-exynos: EHCI EXYNOS driver
[    1.971704] exynos-ehci 12110000.usb: EHCI Host Controller
[    1.976842] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    1.984765] exynos-ehci 12110000.usb: irq 80, io mem 0x12110000
[    2.004164] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    2.004569] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.004724] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.010271] usb usb1: Product: EHCI Host Controller
[    2.015120] usb usb1: Manufacturer: Linux 4.14.150-1-ARCH ehci_hcd
[    2.021269] usb usb1: SerialNumber: 12110000.usb
[    2.026428] hub 1-0:1.0: USB hub found
[    2.029634] hub 1-0:1.0: 3 ports detected
[    2.034509] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.039769] ohci-exynos: OHCI EXYNOS driver
[    2.044089] exynos-ohci 12120000.usb: USB Host Controller
[    2.049278] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    2.057002] exynos-ohci 12120000.usb: irq 80, io mem 0x12120000
[    2.124402] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.124557] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.124720] usb usb2: Product: USB Host Controller
[    2.124831] usb usb2: Manufacturer: Linux 4.14.150-1-ARCH ohci_hcd
[    2.127024] usb usb2: SerialNumber: 12120000.usb
[    2.132219] hub 2-0:1.0: USB hub found
[    2.135379] hub 2-0:1.0: 3 ports detected
[    2.141803] usbcore: registered new interface driver uas
[    2.144737] usbcore: registered new interface driver usb-storage
[    2.150679] usbcore: registered new interface driver ums-cypress
[    2.157341] mousedev: PS/2 mouse device common for all mice
[    2.163578] i2c /dev entries driver
[    2.180769] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    2.198480] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.216938] vdd_ldo30: Bringing 1800000uV into 3300000-3300000uV
[    2.245278] vdd_1.8v_ldo: Bringing 1850000uV into 1500000-1500000uV
[    3.287339] s5m-rtc s2mps14-rtc: rtc core: registered s5m-rtc as rtc0
[    3.291097] s5p-jpeg 11f50000.jpeg: Linked as a consumer to 11f10000.sysmmu
[    3.291309] iommu: Adding device 11f50000.jpeg to group 3
[    3.291796] s5p-jpeg 11f50000.jpeg: encoder device registered as /dev/video30
[    3.292130] s5p-jpeg 11f50000.jpeg: decoder device registered as /dev/video31
[    3.298065] s5p-jpeg 11f50000.jpeg: Samsung S5P JPEG codec
[    3.303740] s5p-jpeg 11f60000.jpeg: Linked as a consumer to 11f20000.sysmmu
[    3.310501] iommu: Adding device 11f60000.jpeg to group 4
[    3.316187] s5p-jpeg 11f60000.jpeg: encoder device registered as /dev/video32
[    3.323105] s5p-jpeg 11f60000.jpeg: decoder device registered as /dev/video33
[    3.330039] s5p-jpeg 11f60000.jpeg: Samsung S5P JPEG codec
[    3.336648] s5p-mfc 11000000.codec: Linked as a consumer to 11200000.sysmmu
[    3.342573] s5p-mfc 11000000.codec: Linked as a consumer to 11210000.sysmmu
[    3.349421] iommu: Adding device 11000000.codec to group 5
[    3.372629] s5p-mfc 11000000.codec: preallocated 16 MiB buffer for the firmware and context buffers
[    3.372952] (NULL device *): Direct firmware load for s5p-mfc-v8.fw failed with error -2
[    3.373136] s5p_mfc_load_firmware:73: Firmware is not present in the /lib/firmware directory nor compiled in kernel
[    3.382488] s5p-mfc 11000000.codec: decoder registered as /dev/video10
[    3.388942] s5p-mfc 11000000.codec: encoder registered as /dev/video11
[    3.397881] exynos-gsc 13e00000.video-scaler: Linked as a consumer to 13e80000.sysmmu
[    3.403150] iommu: Adding device 13e00000.video-scaler to group 6
[    3.410429] exynos-gsc 13e10000.video-scaler: Linked as a consumer to 13e90000.sysmmu
[    3.417012] iommu: Adding device 13e10000.video-scaler to group 7
[    3.443015] thermal thermal_zone0: failed to read out thermal zone (-22)
[    3.444072] thermal thermal_zone1: failed to read out thermal zone (-22)
[    3.445189] thermal thermal_zone2: failed to read out thermal zone (-22)
[    3.446286] thermal thermal_zone3: failed to read out thermal zone (-22)
[    3.450664] thermal thermal_zone4: failed to read out thermal zone (-22)
[    3.457151] device-mapper: uevent: version 1.0.3
[    3.461299] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[    3.483713] sdhci: Secure Digital Host Controller Interface driver
[    3.483838] sdhci: Copyright(c) Pierre Ossman
[    3.484163] Synopsys Designware Multimedia Card Interface Driver
[    3.486398] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    3.492747] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    3.499085] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    3.504475] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 83,64 bit host data width,64 deep fifo
[    3.513878] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    3.540592] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.560502] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    3.560684] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    3.560816] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    3.560971] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 84,64 bit host data width,64 deep fifo
[    3.588590] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.609221] ledtrig-cpu: registered to indicate activity on CPUs
[    3.610127] s5p-secss 10830000.sss: s5p-sss driver registered
[    3.610649] hidraw: raw HID events driver (C) Jiri Kosina
[    3.611009] usbcore: registered new interface driver usbhid
[    3.611120] usbhid: USB HID core driver
[    3.623869] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    3.624141] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    3.626673] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    3.633283] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    3.643949] NET: Registered protocol family 17
[    3.644396] NET: Registered protocol family 15
[    3.648735] Key type dns_resolver registered
[    3.653398] Registering SWP/SWPB emulation handler
[    3.657948] registered taskstats version 1
[    3.661687] Loading compiled-in X.509 certificates
[    3.674907] Key type encrypted registered
[    3.693699] OF: graph: no port node found in /soc/hdmi@14530000
[    3.694686] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[    3.694969] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0a67284)
[    3.695116] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc0a67924)
[    3.698339] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.704913] [drm] No driver support for vblank timestamp query.
[    3.710924] [drm] Cannot find any crtc or sizes
[    3.715732] [drm] Initialized exynos 1.0.0 20110530 for exynos-drm on minor 0
[    3.722669] [drm] Cannot find any crtc or sizes
[    3.728501] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    3.732398] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 3
[    3.740258] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.749401] xhci-hcd xhci-hcd.3.auto: irq 150, io mem 0x12000000
[    3.755481] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    3.762108] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.769298] usb usb3: Product: xHCI Host Controller
[    3.774151] usb usb3: Manufacturer: Linux 4.14.150-1-ARCH xhci-hcd
[    3.780303] usb usb3: SerialNumber: xhci-hcd.3.auto
[    3.785458] hub 3-0:1.0: USB hub found
[    3.788908] hub 3-0:1.0: 1 port detected
[    3.792976] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    3.798248] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 4
[    3.805876] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0  SuperSpeed
[    3.812506] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.820606] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    3.827271] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.834464] usb usb4: Product: xHCI Host Controller
[    3.839314] usb usb4: Manufacturer: Linux 4.14.150-1-ARCH xhci-hcd
[    3.845467] usb usb4: SerialNumber: xhci-hcd.3.auto
[    3.850607] hub 4-0:1.0: USB hub found
[    3.854066] hub 4-0:1.0: 1 port detected
[    3.859986] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    3.863417] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 5
[    3.871239] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.880431] xhci-hcd xhci-hcd.6.auto: irq 151, io mem 0x12400000
[    3.886488] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    3.893130] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.900322] usb usb5: Product: xHCI Host Controller
[    3.905171] usb usb5: Manufacturer: Linux 4.14.150-1-ARCH xhci-hcd
[    3.911322] usb usb5: SerialNumber: xhci-hcd.6.auto
[    3.916453] hub 5-0:1.0: USB hub found
[    3.919900] hub 5-0:1.0: 1 port detected
[    3.923995] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    3.929270] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 6
[    3.936896] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0  SuperSpeed
[    3.943538] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.951627] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[    3.958293] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.965485] usb usb6: Product: xHCI Host Controller
[    3.970335] usb usb6: Manufacturer: Linux 4.14.150-1-ARCH xhci-hcd
[    3.976489] usb usb6: SerialNumber: xhci-hcd.6.auto
[    3.981627] hub 6-0:1.0: USB hub found
[    3.985088] hub 6-0:1.0: 1 port detected
[    3.989881] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[    3.994552] s3c-rtc 101e0000.rtc: warning: invalid RTC value so initializing it
[    4.001851] rtc rtc1: invalid alarm value: 1900-1-1 0:0:0
[    4.007281] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc1
[    4.014452] exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
[    4.021975] exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
[    4.029910] exynos-bus: new bus device registered: soc:bus_fsys_apb (200000 KHz ~ 200000 KHz)
[    4.038344] exynos-bus: new bus device registered: soc:bus_fsys (200000 KHz ~ 200000 KHz)
[    4.046609] exynos-bus: new bus device registered: soc:bus_fsys2 ( 75000 KHz ~ 150000 KHz)
[    4.054934] exynos-bus: new bus device registered: soc:bus_mfc ( 96000 KHz ~ 333000 KHz)
[    4.062942] exynos-bus: new bus device registered: soc:bus_gen ( 89000 KHz ~ 267000 KHz)
[    4.070932] exynos-bus: new bus device registered: soc:bus_peri ( 67000 KHz ~  67000 KHz)
[    4.079184] exynos-bus: new bus device registered: soc:bus_g2d ( 84000 KHz ~ 333000 KHz)
[    4.087218] exynos-bus: new bus device registered: soc:bus_g2d_acp ( 67000 KHz ~ 267000 KHz)
[    4.095620] exynos-bus: new bus device registered: soc:bus_jpeg ( 75000 KHz ~ 300000 KHz)
[    4.103763] exynos-bus: new bus device registered: soc:bus_jpeg_apb ( 84000 KHz ~ 167000 KHz)
[    4.112198] exynos-bus: new bus device registered: soc:bus_disp1_fimd (120000 KHz ~ 200000 KHz)
[    4.120889] exynos-bus: new bus device registered: soc:bus_disp1 (120000 KHz ~ 300000 KHz)
[    4.129110] exynos-bus: new bus device registered: soc:bus_gscl_scaler (150000 KHz ~ 300000 KHz)
[    4.137946] exynos-bus: new bus device registered: soc:bus_mscl ( 84000 KHz ~ 400000 KHz)
[    4.145991] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
[    4.153636] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
[    4.162147] odroid-audio sound: multicodec <-> 3830000.i2s mapping ok
[    4.169935] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[    4.176792] s5m-rtc s2mps14-rtc: setting system clock to 2000-01-01 00:00:25 UTC (946684825)
[    4.188274] ALSA device list:
[    4.188370]   #0: Odroid-XU4
[    4.189929] Freeing unused kernel memory: 1024K
:: running early hook [udev]
Starting version 243.162-2-arch
:: running hook [udev]
:: Triggering uevents...
[    4.296156] usb 3-1: new high-speed USB d

This log is from arch linux with UHS-1 sd card.

[odroid]

Since we don't use Arch linux, it is not easy to trace a root cause at this moment.
Try ubuntu-18.04.3-4.14-minimal-odroid-xu4-20190910.img.xz again.
And show us the log from the u-boot stage.

BTW, when did you buy your XU4? How long did it work fine?

[akhilkalwakurthy]

Since we don't use Arch linux, it is not easy to trace a root cause at this moment.
Try ubuntu-18.04.3-4.14-minimal-odroid-xu4-20190910.img.xz again.
And show us the log from the u-boot stage.

BTW, when did you buy your XU4? How long did it work fine?

I don't have the odroid UART to USB cable or any other 1.8v UART cable, so I'm not able to get logs from uboot stage. I can only use the /dev/ttySAC0 which as I understand requires GPIO to be initialized (please correct me if I got it wrong). Here's the log from SAC0

Code: Select all

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 4.14.141-169 (root@1604_builder_armhf) (gcc version 7.4.0 (Ubuntu/Linaro 7.4.0-1ubuntu1~18.04.1)) #1 SMP PREEMPT Sat Aug 31 23:19:59 -03 2019
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=10c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel Odroid XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0xb6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] On node 0 totalpages: 518656
[    0.000000] free_area_init_node: node 0, pgdat c0d8ecc0, node_mem_map eee25000
[    0.000000]   Normal zone: 1728 pages used for memmap
[    0.000000]   Normal zone: 0 pages reserved
[    0.000000]   Normal zone: 196608 pages, LIFO batch:31
[    0.000000]   HighMem zone: 322048 pages, LIFO batch:31
[    0.000000] Running under secure firmware.
[    0.000000] random: get_random_bytes called from start_kernel+0x90/0x420 with crng_init=0
[    0.000000] percpu: Embedded 17 pages/cpu s37452 r8192 d23988 u69632
[    0.000000] pcpu-alloc: s37452 r8192 d23988 u69632 alloc=17*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5 [0] 6 [0] 7 
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC0,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false udev.log-priority=debug debug ignore_log_level s5p_mfc.mem=16M
[    0.000000] hdmi: using HDMI mode
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] Memory: 1902216K/2074624K available (8192K kernel code, 656K rwdata, 2352K rodata, 1024K init, 318K bss, 41336K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB)
[    0.000000]     vmalloc : 0xf0800000 - 0xff800000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xf0000000   ( 768 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc0900000   (9184 kB)
[    0.000000]       .init : 0xc0c00000 - 0xc0d00000   (1024 kB)
[    0.000000]       .data : 0xc0d00000 - 0xc0da42e0   ( 657 kB)
[    0.000000]        .bss : 0xc0dac378 - 0xc0dfbea0   ( 319 kB)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] hperf_hmp: fast CPUs mask: 000000F0
[    0.000000] hperf_hmp: slow CPUs mask: 0000000F
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] 	Tasks RCU enabled.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000007] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000031] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 49
[    0.001606] Console: colour dummy device 80x30
[    0.002414] console [tty1] enabled
[    0.002456] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[    0.002498] pid_max: default: 32768 minimum: 301
[    0.002686] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.002727] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
[    0.003595] CPU: Testing write buffer coherency: ok
[    0.004511] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.020047] Setting up static identity map for 0x40100000 - 0x40100060
[    0.020670] ARM CCI driver probed
[    0.020908] Exynos MCPM support installed
[    0.027987] Hierarchical SRCU implementation.
[    0.043989] smp: Bringing up secondary CPUs ...
[    0.072374] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.096330] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.124326] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.152325] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.152334] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.172322] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.172329] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.180635] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.180642] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.188626] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.188633] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.188888] smp: Brought up 1 node, 8 CPUs
[    0.188935] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.188958] CPU: All CPU(s) started in HYP mode.
[    0.188977] CPU: Virtualization extensions available.
[    0.190835] devtmpfs: initialized
[    0.208277] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.208473] hperf_hmp: registered cpufreq transition notifier
[    0.208661] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[    0.208697] futex hash table entries: 2048 (order: 5, 131072 bytes)
[    0.211466] pinctrl core: initialized pinctrl subsystem
[    0.213629] NET: Registered protocol family 16
[    0.218363] DMA: preallocated 1024 KiB pool for atomic coherent allocations
[    0.224433] cpuidle: using governor menu
[    0.225298] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.225325] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.233775] exynos-audss-clk 3810000.audss-clock-controller: epll 180633609
[    0.256424] EXYNOS5420 PMU initialized
[    0.299391] usbcore: registered new interface driver usbfs
[    0.299459] usbcore: registered new interface driver hub
[    0.299612] usbcore: registered new device driver usb
[    0.300055] i2c-gpio soc:i2c-hdmi: using pins 177 (SDA) and 178 (SCL)
[    0.300664] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.300691] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.300913] s3c-i2c 12c70000.i2c: i2c-1: S3C I2C adapter
[    0.301430] media: Linux media interface: v0.10
[    0.301484] Linux video capture interface: v2.00
[    0.301598] pps_core: LinuxPPS API ver. 1 registered
[    0.301618] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.301888] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    0.302737] Advanced Linux Sound Architecture Driver Initialized.
[    0.304014] clocksource: Switched to clocksource mct-frc
[    0.364627] VFS: Disk quotas dquot_6.6.0
[    0.364710] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.378649] NET: Registered protocol family 2
[    0.379231] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
[    0.379328] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[    0.379496] TCP: Hash tables configured (established 8192 bind 8192)
[    0.379611] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    0.379663] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    0.379872] NET: Registered protocol family 1
[    0.380590] RPC: Registered named UNIX socket transport module.
[    0.380613] RPC: Registered udp transport module.
[    0.380631] RPC: Registered tcp transport module.
[    0.380649] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.380856] Trying to unpack rootfs image as initramfs...
[    0.668035] random: fast init done
[    0.838454] Freeing initrd memory: 8124K
[    0.839959] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.841016] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.844521] audit: initializing netlink subsys (disabled)
[    0.844746] audit: type=2000 audit(0.844:1): state=initialized audit_enabled=0 res=1
[    0.845304] Initialise system trusted keyrings
[    0.845495] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.852821] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.853681] NFS: Registering the id_resolver key type
[    0.853714] Key type id_resolver registered
[    0.853732] Key type id_legacy registered
[    0.853761] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.853812] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.858716] Key type asymmetric registered
[    0.858738] Asymmetric key parser 'x509' registered
[    0.858802] bounce: pool size: 64 pages
[    0.858863] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 245)
[    0.859086] io scheduler noop registered
[    0.859109] io scheduler deadline registered
[    0.859270] io scheduler cfq registered (default)
[    0.859292] io scheduler mq-deadline registered
[    0.859310] io scheduler kyber registered
[    0.859567] io scheduler bfq registered
[    0.862040] samsung-usb2-phy 12130000.phy: 12130000.phy supply vbus not found, using dummy regulator
[    0.863028] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus not found, using dummy regulator
[    0.863115] exynos5_usb3drd_phy 12100000.phy: 12100000.phy supply vbus-boost not found, using dummy regulator
[    0.863511] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus not found, using dummy regulator
[    0.863594] exynos5_usb3drd_phy 12500000.phy: 12500000.phy supply vbus-boost not found, using dummy regulator
[    0.868510] dma-pl330 3880000.adma: Loaded driver for PL330 DMAC-241330
[    0.868536] dma-pl330 3880000.adma: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.871087] dma-pl330 121a0000.pdma: Loaded driver for PL330 DMAC-241330
[    0.871115] dma-pl330 121a0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.873732] dma-pl330 121b0000.pdma: Loaded driver for PL330 DMAC-241330
[    0.873758] dma-pl330 121b0000.pdma: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.874599] dma-pl330 10800000.mdma: Loaded driver for PL330 DMAC-241330
[    0.874625] dma-pl330 10800000.mdma: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.934979] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.937363] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 58, base_baud = 0) is a S3C6400/10
[    1.883332] console [ttySAC0] enabled
[    1.887331] 12c10000.serial: ttySAC1 at MMIO 0x12c10000 (irq = 59, base_baud = 0) is a S3C6400/10
[    1.896207] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 60, base_baud = 0) is a S3C6400/10
[    1.905004] 12c30000.serial: ttySAC3 at MMIO 0x12c30000 (irq = 61, base_baud = 0) is a S3C6400/10
[    1.915665] exynos-mixer 14450000.mixer: Linked as a consumer to 14650000.sysmmu
[    1.920904] iommu: Adding device 14450000.mixer to group 0
[    1.927983] exynos-hdmi 14530000.hdmi: Failed to get supply 'vdd': -517
[    1.933592] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a60000.sysmmu
[    1.940364] exynos-drm-g2d 10850000.g2d: Linked as a consumer to 10a70000.sysmmu
[    1.947670] iommu: Adding device 10850000.g2d to group 1
[    1.953279] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully probed.
[    1.961885] exynos-rot 11c00000.rotator: Linked as a consumer to 11d40000.sysmmu
[    1.968201] iommu: Adding device 11c00000.rotator to group 2
[    1.974159] exynos-rot 11c00000.rotator: The exynos rotator is probed successfully
[    1.982113] exynos-drm-ipp exynos-drm-ipp: drm ipp registered successfully.
[    1.992616] mali 11800000.mali: Continuing without Mali regulator control
[    1.995738] mali 11800000.mali: GPU identified as 0x0620 r0p1 status 0
[    2.002024] mali 11800000.mali: Protected mode not available
[    2.007575] devfreq devfreq0: Couldn't update frequency transition information.
[    2.015134] mali 11800000.mali: Probed as mali0
[    2.028742] brd: module loaded
[    2.029462] libphy: Fixed MDIO Bus: probed
[    2.029905] usbcore: registered new interface driver r8152
[    2.031495] usbcore: registered new interface driver cdc_ether
[    2.037339] usbcore: registered new interface driver cdc_subset
[    2.045334] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.049707] ehci-exynos: EHCI EXYNOS driver
[    2.054193] exynos-ehci 12110000.usb: EHCI Host Controller
[    2.059328] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    2.067214] exynos-ehci 12110000.usb: irq 80, io mem 0x12110000
[    2.088068] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    2.088475] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.088630] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.092761] usb usb1: Product: EHCI Host Controller
[    2.097608] usb usb1: Manufacturer: Linux 4.14.141-169 ehci_hcd
[    2.103498] usb usb1: SerialNumber: 12110000.usb
[    2.108670] hub 1-0:1.0: USB hub found
[    2.111822] hub 1-0:1.0: 3 ports detected
[    2.116802] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.121999] ohci-exynos: OHCI EXYNOS driver
[    2.126317] exynos-ohci 12120000.usb: USB Host Controller
[    2.131504] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    2.139219] exynos-ohci 12120000.usb: irq 80, io mem 0x12120000
[    2.208302] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.208456] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.208618] usb usb2: Product: USB Host Controller
[    2.208729] usb usb2: Manufacturer: Linux 4.14.141-169 ohci_hcd
[    2.210665] usb usb2: SerialNumber: 12120000.usb
[    2.215816] hub 2-0:1.0: USB hub found
[    2.219056] hub 2-0:1.0: 3 ports detected
[    2.226097] mousedev: PS/2 mouse device common for all mice
[    2.229826] i2c /dev entries driver
[    2.247760] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    2.265907] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.284646] vdd_ldo30: Bringing 1800000uV into 3300000-3300000uV
[    2.312931] vdd_1.8v_ldo: Bringing 1850000uV into 1500000-1500000uV
[    3.355234] s5m-rtc s2mps14-rtc: rtc core: registered s5m-rtc as rtc0
[    3.359400] s5p-jpeg 11f50000.jpeg: Linked as a consumer to 11f10000.sysmmu
[    3.359606] iommu: Adding device 11f50000.jpeg to group 3
[    3.360151] s5p-jpeg 11f50000.jpeg: encoder device registered as /dev/video30
[    3.360476] s5p-jpeg 11f50000.jpeg: decoder device registered as /dev/video31
[    3.365960] s5p-jpeg 11f50000.jpeg: Samsung S5P JPEG codec
[    3.371631] s5p-jpeg 11f60000.jpeg: Linked as a consumer to 11f20000.sysmmu
[    3.378397] iommu: Adding device 11f60000.jpeg to group 4
[    3.384099] s5p-jpeg 11f60000.jpeg: encoder device registered as /dev/video32
[    3.390998] s5p-jpeg 11f60000.jpeg: decoder device registered as /dev/video33
[    3.397935] s5p-jpeg 11f60000.jpeg: Samsung S5P JPEG codec
[    3.404544] s5p-mfc 11000000.codec: Linked as a consumer to 11200000.sysmmu
[    3.410460] s5p-mfc 11000000.codec: Linked as a consumer to 11210000.sysmmu
[    3.417320] iommu: Adding device 11000000.codec to group 5
[    3.440569] s5p-mfc 11000000.codec: preallocated 16 MiB buffer for the firmware and context buffers
[    3.440876] (NULL device *): Direct firmware load for s5p-mfc-v8.fw failed with error -2
[    3.441060] s5p_mfc_load_firmware:73: Firmware is not present in the /lib/firmware directory nor compiled in kernel
[    3.450382] s5p-mfc 11000000.codec: decoder registered as /dev/video10
[    3.456842] s5p-mfc 11000000.codec: encoder registered as /dev/video11
[    3.464968] exynos-gsc 13e00000.video-scaler: Linked as a consumer to 13e80000.sysmmu
[    3.471051] iommu: Adding device 13e00000.video-scaler to group 6
[    3.478340] exynos-gsc 13e10000.video-scaler: Linked as a consumer to 13e90000.sysmmu
[    3.484906] iommu: Adding device 13e10000.video-scaler to group 7
[    3.510821] thermal thermal_zone0: failed to read out thermal zone (-22)
[    3.511871] thermal thermal_zone1: failed to read out thermal zone (-22)
[    3.512991] thermal thermal_zone2: failed to read out thermal zone (-22)
[    3.514086] thermal thermal_zone3: failed to read out thermal zone (-22)
[    3.518559] thermal thermal_zone4: failed to read out thermal zone (-22)
[    3.525032] device-mapper: uevent: version 1.0.3
[    3.529205] device-mapper: ioctl: 4.37.0-ioctl (2017-09-20) initialised: dm-devel@redhat.com
[    3.551622] sdhci: Secure Digital Host Controller Interface driver
[    3.551746] sdhci: Copyright(c) Pierre Ossman
[    3.552069] Synopsys Designware Multimedia Card Interface Driver
[    3.554296] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    3.560644] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    3.566982] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    3.572371] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 83,64 bit host data width,64 deep fifo
[    3.581773] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    3.608498] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.628400] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    3.628581] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    3.628713] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    3.628871] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 84,64 bit host data width,64 deep fifo
[    3.656495] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    3.677122] ledtrig-cpu: registered to indicate activity on CPUs
[    3.678029] s5p-secss 10830000.sss: s5p-sss driver registered
[    3.678548] hidraw: raw HID events driver (C) Jiri Kosina
[    3.689493] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    3.689733] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    3.689967] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    3.691795] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    3.702463] NET: Registered protocol family 17
[    3.702708] NET: Registered protocol family 15
[    3.707179] Key type dns_resolver registered
[    3.711805] Registering SWP/SWPB emulation handler
[    3.716548] registered taskstats version 1
[    3.720226] Loading compiled-in X.509 certificates
[    3.730359] Key type encrypted registered
[    3.749061] OF: graph: no port node found in /soc/hdmi@14530000
[    3.750040] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[    3.750325] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0966344)
[    3.750468] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc09669e4)
[    3.755839] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[    3.762422] [drm] No driver support for vblank timestamp query.
[    3.768427] [drm] Cannot find any crtc or sizes
[    3.773245] [drm] Initialized exynos 1.0.0 20110530 for exynos-drm on minor 0
[    3.780211] [drm] Cannot find any crtc or sizes
[    3.785949] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    3.789905] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 3
[    3.797736] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.806911] xhci-hcd xhci-hcd.3.auto: irq 149, io mem 0x12000000
[    3.812991] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[    3.819616] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.826807] usb usb3: Product: xHCI Host Controller
[    3.831655] usb usb3: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    3.837551] usb usb3: SerialNumber: xhci-hcd.3.auto
[    3.842712] hub 3-0:1.0: USB hub found
[    3.846151] hub 3-0:1.0: 1 port detected
[    3.850264] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    3.855494] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 4
[    3.863124] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0  SuperSpeed
[    3.869753] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.877852] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[    3.884520] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.885617] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz, actual 50000000HZ div = 0)
[    3.891718] usb usb4: Product: xHCI Host Controller
[    3.902847] mmc1: new ultra high speed DDR50 SDHC card at address aaaa
[    3.906273] usb usb4: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    3.913676] mmcblk1: mmc1:aaaa SS16G 14.8 GiB 
[    3.918664] usb usb4: SerialNumber: xhci-hcd.3.auto
[    3.928257] hub 4-0:1.0: USB hub found
[    3.931653] hub 4-0:1.0: 1 port detected
[    3.935787]  mmcblk1: p1 p2
[    3.938972] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    3.943801] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 5
[    3.951629] xhci-hcd xhci-hcd.6.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.960808] xhci-hcd xhci-hcd.6.auto: irq 150, io mem 0x12400000
[    3.966892] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002
[    3.973514] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.980706] usb usb5: Product: xHCI Host Controller
[    3.985555] usb usb5: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    3.991448] usb usb5: SerialNumber: xhci-hcd.6.auto
[    3.996611] hub 5-0:1.0: USB hub found
[    4.000051] hub 5-0:1.0: 1 port detected
[    4.004122] xhci-hcd xhci-hcd.6.auto: xHCI Host Controller
[    4.009396] xhci-hcd xhci-hcd.6.auto: new USB bus registered, assigned bus number 6
[    4.017015] xhci-hcd xhci-hcd.6.auto: Host supports USB 3.0  SuperSpeed
[    4.023665] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.031752] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003
[    4.038418] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    4.045608] usb usb6: Product: xHCI Host Controller
[    4.050459] usb usb6: Manufacturer: Linux 4.14.141-169 xhci-hcd
[    4.056352] usb usb6: SerialNumber: xhci-hcd.6.auto
[    4.061488] hub 6-0:1.0: USB hub found
[    4.064952] hub 6-0:1.0: 1 port detected
[    4.069764] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[    4.074417] s3c-rtc 101e0000.rtc: warning: invalid RTC value so initializing it
[    4.081712] rtc rtc1: invalid alarm value: 1900-1-1 0:0:0
[    4.087143] s3c-rtc 101e0000.rtc: rtc core: registered s3c as rtc1
[    4.094328] exynos-bus: new bus device registered: soc:bus_wcore ( 84000 KHz ~ 400000 KHz)
[    4.101836] exynos-bus: new bus device registered: soc:bus_noc ( 67000 KHz ~ 100000 KHz)
[    4.109766] exynos-bus: new bus device registered: soc:bus_fsys_apb (200000 KHz ~ 200000 KHz)
[    4.118208] exynos-bus: new bus device registered: soc:bus_fsys (200000 KHz ~ 200000 KHz)
[    4.126488] exynos-bus: new bus device registered: soc:bus_fsys2 ( 75000 KHz ~ 150000 KHz)
[    4.134790] exynos-bus: new bus device registered: soc:bus_mfc ( 96000 KHz ~ 333000 KHz)
[    4.142806] exynos-bus: new bus device registered: soc:bus_gen ( 89000 KHz ~ 267000 KHz)
[    4.150793] exynos-bus: new bus device registered: soc:bus_peri ( 67000 KHz ~  67000 KHz)
[    4.159057] exynos-bus: new bus device registered: soc:bus_g2d ( 84000 KHz ~ 333000 KHz)
[    4.167074] exynos-bus: new bus device registered: soc:bus_g2d_acp ( 67000 KHz ~ 267000 KHz)
[    4.175478] exynos-bus: new bus device registered: soc:bus_jpeg ( 75000 KHz ~ 300000 KHz)
[    4.183627] exynos-bus: new bus device registered: soc:bus_jpeg_apb ( 84000 KHz ~ 167000 KHz)
[    4.192074] exynos-bus: new bus device registered: soc:bus_disp1_fimd (120000 KHz ~ 200000 KHz)
[    4.200745] exynos-bus: new bus device registered: soc:bus_disp1 (120000 KHz ~ 300000 KHz)
[    4.208975] exynos-bus: new bus device registered: soc:bus_gscl_scaler (150000 KHz ~ 300000 KHz)
[    4.217802] exynos-bus: new bus device registered: soc:bus_mscl ( 84000 KHz ~ 400000 KHz)
[    4.225855] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
[    4.233499] samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
[    4.242006] odroid-audio sound: multicodec <-> 3830000.i2s mapping ok
[    4.251175] s5m-rtc s2mps14-rtc: setting system clock to 2000-01-01 00:02:17 UTC (946684937)
[    4.261101] ALSA device list:
[    4.261195]   #0: Odroid-XU4
[    4.263108] Freeing unused kernel memory: 1024K
Loading, please wait...
[    4.305612] systemd-udevd[136]: set children_max to 24
[    4.305961] systemd-udevd[136]: starting version 237
[    4.307043] systemd-udevd[137]: hwdb.bin does not exist, please run systemd-hwdb update
[    4.308127] systemd-udevd[137]: Load module index
[    4.308522] systemd-udevd[137]: Network interface NamePolicy= disabled on kernel command line, ignoring.
[    4.315600] systemd-udevd[137]: timestamp of '/lib/systemd/network' changed
[    4.322752] systemd-udevd[137]: Parsed configuration file /lib/systemd/network/99-default.link
[    4.331068] systemd-udevd[137]: Created link configuration context.
[    4.337335] systemd-udevd[137]: timestamp of '/lib/udev/rules.d' changed
[    4.344278] systemd-udevd[137]: Reading rules file: /lib/udev/rules.d/10-odroid.rules
[    4.376069] usb 3-1: n⸮

I got my XU4 in Aug, 2018. It worked fine till Jan, 2020. It was my NAS. One day, it froze and did not respond even after waiting for 2 hours. I had to disconnect the power and it never booted again
P.S. It wasn't on all the time. I used it for only 1-2 hrs a day

[mad_ady]

It might be this issue?
https://r.tapatalk.com/shareLink/topic? ... source=app

[akhilkalwakurthy]

It might be this issue?
https://r.tapatalk.com/shareLink/topic? ... source=app

Thanks, but it doesn't look I'm having the same issue.

[akhilkalwakurthy]

Since we don't use Arch linux, it is not easy to trace a root cause at this moment.
Try ubuntu-18.04.3-4.14-minimal-odroid-xu4-20190910.img.xz again.
And show us the log from the u-boot stage.

BTW, when did you buy your XU4? How long did it work fine?

I've got logs from u-boot stage. https://paste.ubuntu.com/p/d5q8KSV26v

don't know if it is the isuue but I get "mmc_init -5" and "bad CRC" for all SD cards I have
Cards I've tried are:
SanDisk 16GB, Class-4, HC-1
Strontium Nitro A1 32GB Class-10, HC-1, UHS-1
Samsung EVO Select 64GB, XC-1, UHS-3

[odroid]

I couldn't find any clue in the u-boot message.
Ignore that messages since you don't use an eMMC module.

Those SD cards must be compatible with XU4.

Please try this Android image to check whether there is a hardware issue or not.
https://wiki.odroid.com/odroid-xu4/os_i ... droid/v6.8

File name is android-4.4.4-alpha-6.8-sd_installer-odroidxu4-20190821.img.zip
https://dn.odroid.com/5422/ODROID-XU4/A ... g-21-2019/

[tobetter]

Since we don't use Arch linux, it is not easy to trace a root cause at this moment.
Try ubuntu-18.04.3-4.14-minimal-odroid-xu4-20190910.img.xz again.
And show us the log from the u-boot stage.

BTW, when did you buy your XU4? How long did it work fine?

I've got logs from u-boot stage. https://paste.ubuntu.com/p/d5q8KSV26v

don't know if it is the isuue but I get "mmc_init -5" and "bad CRC" for all SD cards I have
Cards I've tried are:
SanDisk 16GB, Class-4, HC-1
Strontium Nitro A1 32GB Class-10, HC-1, UHS-1
Samsung EVO Select 64GB, XC-1, UHS-3

The error mmc_init: -5, time 4 is not the problem for your issue and your SD cards are properly working. The logs are not sufficient to find out the issue. If your XU4 keeps rebooting, please do remove all attached USB devices and try again. Also, you could remove console=tty1 in boot.ini to see more logs.

[akhilkalwakurthy]

I couldn't find any clue in the u-boot message.
Ignore that messages since you don't use an eMMC module.

Those SD cards must be compatible with XU4.

Please try this Android image to check whether there is a hardware issue or not.
https://wiki.odroid.com/odroid-xu4/os_i ... droid/v6.8

File name is android-4.4.4-alpha-6.8-sd_installer-odroidxu4-20190821.img.zip
https://dn.odroid.com/5422/ODROID-XU4/A ... g-21-2019/

I tried with the android image and here's the log https://paste.ubuntu.com/p/TxWj6PnDZn
At line 1001 in that log it says "shell@odroidxu3", does that mean it did boot? After that, it rebooted again...

[akhilkalwakurthy]

The error mmc_init: -5, time 4 is not the problem for your issue and your SD cards are properly working. The logs are not sufficient to find out the issue. If your XU4 keeps rebooting, please do remove all attached USB devices and try again. Also, you could remove console=tty1 in boot.ini to see more logs.

I tried removing the console=tty1. But, the log is exactly the same. I did see that the command line has changed in logs. Other than that, it's exactly the same

[odroid]

Android Self-installation process might take up to 1~2 minutes and will reboot once automatically.
After that you can access the Android home screen via HDMI display with a mouse/keyboard.

[akhilkalwakurthy]

Android Self-installation process might take up to 1~2 minutes and will reboot once automatically.
After that you can access the Android home screen via HDMI display with a mouse/keyboard.

Sorry, I wasn't very clear.
Android self-installation process completed fine and it rebooted as expected. It started to boot and then for some reason rebooted. This goes on and on.
There's nothing output to HDMI. My monitor says "HDMI connected" and then "no signal" like in a loop.
I've captured the UART logs starting from the self-installation process until the device rebooted a few times, using plink to a file. The Odroid and the file content is untouched while capturing the logs.

odroid_android_op.txt

(300.16 KiB) Downloaded 29 times

Sometimes it does get to the android terminal but, before I can type any command or do anything at all, reboots (again, nothing on HDMI)

[odroid]

I think you did as much as you could and there seems to be a hardware issue probably.
I don't know how it worked several months and died recently.

Do you have another 5V/4A PSU?
Since some people reported the random reboot issue was caused by a unstable PSU,

Our warranty period is only two months. Sorry about that.
viewtopic.php?f=53&t=661

[akhilkalwakurthy]

I think you did as much as you could and there seems to be a hardware issue probably.
I don't know how it worked several months and died recently.

Do you have another 5V/4A PSU?
Since some people reported the random reboot issue was caused by a unstable PSU,

Our warranty period is only two months. Sorry about that.
viewtopic.php?f=53&t=661

No, I don't have another PSU that can supply 5V4A. But, I did check the PSU output with DMM and it was a stable 5.21V output, 5V0 pin on CON10 connector gives me about 5.02V to 5.15V

[odroid]

If the 5V0 rail voltage level on the CON10 is not lower than 4.8 Volt in the booting process, your PSU must be fine.

But there was no critical error message in the Kernel booting log and I have no idea what is wrong indeed.

[mad_ady]

@odroid is this the same behavior one might expect if there is a broken temperature sensor and the board thinks it's overheating? Or does it simply shut down then?

[akhilkalwakurthy]

I'm starting to doubt that my board is being reset (hard reset probably?) instead of reboot.
I can interrupt the booting process by pressing the "return" key at the uboot prompt. It'd drop me into uboot shell and I can execute commands there. While in the shell, my board won't reboot automatically.
While booting any distro, I can see that the kernel loads and the init process is started. Then I'm back to uboot again. I've tried setting the "rescue", "emergency" and "init=/bin/sh" parameters but, I'm not able to get to the shell.
Rarely it gets to login prompt but, before I can type anything, it is back to uboot.

[akhilkalwakurthy]

Progress
@odroid @mad_ady
I've managed to stop the boot process and get a pre-mount debug shell on Arch Linux.
I couldn't get it on ubuntu or android. Even on Arch, I had to set "udev.log-priority=debug". Maybe it needed some delay, I'm not sure.
Thermal zone temps were in the range of 40~50 C. I get spammed by messages like
"thermal_zone3: sd-device: Not a key-value pair: '0'
sd-device-monitor: Failed to create device from received message: Invalid argument"
If I try to continue the boot process, it gets to the welcome message and reboots...

I haven't gone through the entire log yet. I'm attaching it here in case you are interested.

odroid_putty_20200201_164649.txt

(854.82 KiB) Downloaded 35 times

(P.S. sorry for all the trouble, I love the board and I want to do whatever I can to fix it).

[odroid]

@odroid is this the same behavior one might expect if there is a broken temperature sensor and the board thinks it's overheating? Or does it simply shut down then?

It must shutdown instead of rebooting.

@akhilkalwakurthy,
I've tried to read 13478 lines of the very long log.
I guess the SD card host interface seems to be broken.
To prove my assumption, you might need to place the root file system in a USB storage.

[akhilkalwakurthy]

@akhilkalwakurthy,
I've tried to read 13478 lines of the very long log.
I guess the SD card host interface seems to be broken.
To prove my assumption, you might need to place the root file system in a USB storage.

Tried placing the root file system in USB storage, same story. I can mount my sd card in the pre-mount shell and read/write to it without any issues. The USB drive is recognized too.

[odroid]

The idea that can come out of my brain seems to have run out. Sorry about that.
I hope other users can give you other ideas.

[akhilkalwakurthy]

The idea that can come out of my brain seems to have run out. Sorry about that.
I hope other users can give you other ideas.

I've managed to get my Odroid up and running again... It was the PSU.
So, here's what happened. Since different OSes were failing at different stages, I've decided to tryout all the available OSes and see if I could get more info. I was trying out the armbian with kernel 5.4. It did not boot but, the power LED started to blink. DMM showed the voltage on 5v0 rail was varying from 1.2V to 5.14V. So, pulled out the ATX unit from my old desktop and connected it to the odroid. It just booted up fine.

Thanks a lot!