Kernel 3.8.13(X/X2/U2/U3) For Ubuntu(Server)/Fedora/Debian

Moderators: odroid, meveric, mdrjr

Kernel 3.8.13(X/X2/U2/U3) For Ubuntu(Server)/Fedora/Debian

Unread postby mdrjr » Sun Jun 16, 2013 2:16 am

Its been a while that we are working on kernel 3.8.13.3 and I fell great on doing this release.
We do consider this kernel stable. We'll update this kernel and keep it running.
Kernel 3.8 isn't on its End of Life (EOL). Canonical will support 3.8 until Ago/2014. They'll be back-porting patchs and fixes!
All of those will be merge.. As we already did with the current .2 release!

This script can update Ubuntu or Fedora or OpenSUSE images to the latest kernel!

How to use it?
On your board type:
Code: Select all
wget http://builder.mdrjr.net/tools/kernel-update.sh
chmod +x kernel-update.sh
sudo ./kernel-update.sh


The script above will download the latest version, build every midnight and install on your board.
The same script works for Ubuntu/Fedora/OpenSUSE

Keep in mind that I'm a human being.. And I have probably forgot to add some common drivers on this kernel that most of the people will use.. So, for this.. Since now I have this machine building the kernel for me.. I can even issue a build now to have a latest kernel with what you need.

If you need one device driver supported that is supported on Kernel 3.8.. I'll add to hardkernel defconfig and uppon midnight (GMT-3 Time) you'll have it done.
Post on this thread, what kernel option you need supported and I'll add to the defconfig, so the next build you'll have it as default in our defconfig.
You can even add this script to a cron entry so you have daily updates installed! Simple as that.. The script also back-ups the current kernel

This new kernel also support several new screen resolutions...
viewtopic.php?f=52&t=2947

Also if you check the: /media/boot (Ubuntu) or /boot (Fedora/OpenSUSE)
There's for each resolution an HDMI and a DVI version of the boot.scr
Some screens that wasn't working because they are a HDMI(DVI) screen will probably now work.
Including some HDMI->DVI adapters on some screens.. not 100% guarantee's

Please not that some of those resolutions above even that they are supported by the HDMI PHY
They aren't supported by Mali.. If you have mali enabled and one of those resolutions doesn't work.
Sorry, we can't do much here. Since its Mali implementation that doesn't allow it :(

Those nightly builds are proudly built on a ODROID-XU
For for information: viewtopic.php?f=64&t=1889
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby G[3z] » Sun Jun 16, 2013 10:53 pm

If you need one device driver supported that is supported on Kernel 3.8.. I'll add to hardkernel defconfig

i would like hfsplus enabled if possible, thanks for the effort :)
G[3z]
 
Posts: 7
Joined: Tue Jun 04, 2013 7:50 am
languages_spoken: italian english
ODROIDs: ODROID U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 17, 2013 12:45 am

G[3z] wrote:
If you need one device driver supported that is supported on Kernel 3.8.. I'll add to hardkernel defconfig

i would like hfsplus enabled if possible, thanks for the effort :)


https://github.com/hardkernel/linux/com ... e921aa078e

Done, next build will have it :)
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: AW: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby temptemp » Mon Jun 17, 2013 5:33 am

I need the modules:
xc5000.ko
drxk.ko
em28xx.ko
enabled

Thanks in advance
temptemp
 
Posts: 87
Joined: Sat May 25, 2013 9:53 pm
languages_spoken: english

Re: AW: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 17, 2013 6:03 am

temptemp wrote:I need the modules:
xc5000.ko
drxk.ko
em28xx.ko
enabled

Thanks in advance


https://github.com/hardkernel/linux/com ... f6ff61ff51
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby llongeri » Mon Jun 17, 2013 11:38 am

Hi,
Is the I2C driver enabled?
llongeri
 
Posts: 20
Joined: Thu May 30, 2013 12:09 pm
languages_spoken: english
ODROIDs: X2, U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby hulkenstrong » Mon Jun 17, 2013 6:50 pm

First great kernel. Fixed my bluetooth pairing trouble (MS wedge mobile keyboard)

But now mount -t cifs doesnt work (neither do mount -t smbfs). Rather basic function to be able to mount windows share I thhink. Is the cifs module missing?

As a side note I am using Firefox with greasemonkey/ViewTube piped to xine to watch flash videos. Worked great on the old kernel 3.0.7.5 but causes distorted/noisy audio output on the new kernel 3.8.13.2. Video plays smoothly thou.
hulkenstrong
 
Posts: 57
Joined: Mon Jun 17, 2013 6:42 pm
languages_spoken: english,swedish
ODROIDs: Odroid-U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 17, 2013 9:23 pm

hulkenstrong wrote:First great kernel. Fixed my bluetooth pairing trouble (MS wedge mobile keyboard)

But now mount -t cifs doesnt work (neither do mount -t smbfs). Rather basic function to be able to mount windows share I thhink. Is the cifs module missing?

As a side note I am using Firefox with greasemonkey/ViewTube piped to xine to watch flash videos. Worked great on the old kernel 3.0.7.5 but causes distorted/noisy audio output on the new kernel 3.8.13.2. Video plays smoothly thou.


About the CIFS! Sorry, my bad I've forgot to add this module :(
https://github.com/hardkernel/linux/com ... 785a297bef

I'll start a manual build now. Should be done and upload in 2 hours.

I'll test this playback later today.. I havent tested that..
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby hulkenstrong » Mon Jun 17, 2013 10:03 pm

mdrjr wrote:
hulkenstrong wrote:First great kernel. Fixed my bluetooth pairing trouble (MS wedge mobile keyboard)

But now mount -t cifs doesnt work (neither do mount -t smbfs). Rather basic function to be able to mount windows share I thhink. Is the cifs module missing?

As a side note I am using Firefox with greasemonkey/ViewTube piped to xine to watch flash videos. Worked great on the old kernel 3.0.7.5 but causes distorted/noisy audio output on the new kernel 3.8.13.2. Video plays smoothly thou.


About the CIFS! Sorry, my bad I've forgot to add this module :(
https://github.com/hardkernel/linux/com ... 785a297bef

I'll start a manual build now. Should be done and upload in 2 hours.

I'll test this playback later today.. I havent tested that..


Thank you!

mounting my NAS is the final peace before I can create a stable backup image file of the system. Then its of to fun and games. Trying 2.0GHz stresstesting and running a few emulators etc.

About the audio, all seems fine after uninstalling pulse-audio. I dont need pulse audio for my current apps and most likely/hopefully not for future apps anyway.
hulkenstrong
 
Posts: 57
Joined: Mon Jun 17, 2013 6:42 pm
languages_spoken: english,swedish
ODROIDs: Odroid-U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby folderman » Mon Jun 17, 2013 11:07 pm

Hi mdrjr,

Any way we can compile the kernel ourself? Thanks for your great input, playing with my odroid-x is a great experience.

Rgds,
Kenneth
folderman
 
Posts: 19
Joined: Thu Feb 28, 2013 2:43 pm
languages_spoken: english
ODROIDs: odroid-x

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 17, 2013 11:43 pm

folderman wrote:Hi mdrjr,

Any way we can compile the kernel ourself? Thanks for your great input, playing with my odroid-x is a great experience.

Rgds,
Kenneth


Well sources are on the git.. build as usual ;) native builds are the must common way :)
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby Blue-Tiger » Tue Jun 18, 2013 12:32 am

Oh, I love this new way of handling updates. Thanks for having put in the work to set this up (and of course thanks a lot for 3.8!)

That said, I'd appreciate if the aes and xts crypto-modules could be enabled for future builds, please :)
Blue-Tiger
 
Posts: 40
Joined: Wed Feb 27, 2013 6:33 am
languages_spoken: english,german
ODROIDs: U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Tue Jun 18, 2013 12:55 am

Blue-Tiger wrote:Oh, I love this new way of handling updates. Thanks for having put in the work to set this up (and of course thanks a lot for 3.8!)

That said, I'd appreciate if the aes and xts crypto-modules could be enabled for future builds, please :)



https://github.com/hardkernel/linux/com ... e48db3e670

Here we go.. ;)
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby Blue-Tiger » Tue Jun 18, 2013 1:32 am

Thanks a lot! :)
Blue-Tiger
 
Posts: 40
Joined: Wed Feb 27, 2013 6:33 am
languages_spoken: english,german
ODROIDs: U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby sert00 » Tue Jun 18, 2013 2:46 am

with 3.8 kernels my creative X-Fi sorround 5.1 Usb audio card is detected without any extra work like recompile kernel etc.yesterday night dd the xfce robroyhall image on a sdcard only to try somethings and i was happy to see it was recognized when i connect it.great!
2x Odroid-U2
2x Odroid-XU-E
Odroid-U3
Odroid-C1+
Odroid-XU4
Lcd touch panel 10.1"
....and many of the goodies available....
User avatar
sert00
 
Posts: 745
Joined: Sun Feb 24, 2013 12:26 am
languages_spoken: english,italian
ODROIDs: ODROID-U2*2__ODROID-U3__ODROID-XU-E__ODROID-XU-Ebeta__ODROID-C1__ODROID-XU4

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby G[3z] » Tue Jun 18, 2013 7:25 am

Hello i did upgrade from 3.0.80 to this 3.8.13.2 with your script.
i did the upgrade with a 16gb sd inserted in the slot of my U2.
wired thing is that now the SD and usb disk are not automounted when plugged in (they where in 3.0.x)
and if i reboot with the sd inserted i see it on the desktop but if i doubleclick it it gives me a mount error talking about bad sector
this is my gParted screenshot
Image

as you can see U2 thinks the sd is mmcblk0 (while before it was 1 ) and wants to mount it on /media/boot
can anyone help me with this ? thanks
G[3z]
 
Posts: 7
Joined: Tue Jun 04, 2013 7:50 am
languages_spoken: italian english
ODROIDs: ODROID U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Tue Jun 18, 2013 7:36 am

Do you use eMMC and SD at the same time ?

if so, try changing it for now, I'll check the initialization code for eMMC and SD.
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby bluc » Tue Jun 18, 2013 10:16 am

any chance of getting the v4l-dvb drivers included in this kernal in particular the dib0700 driver? Will enable some tv tuner support cheers.
bluc
 
Posts: 93
Joined: Sun Apr 28, 2013 2:24 pm
languages_spoken: english

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Tue Jun 18, 2013 10:21 am

bluc wrote:any chance of getting the v4l-dvb drivers included in this kernal in particular the dib0700 driver? Will enable some tv tuner support cheers.


Its already included! DiBcom 7000PC/MA/MB/PA/PB/MC
Their modules are present already.
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby phil » Tue Jun 18, 2013 3:40 pm

are you able to add MCEUSB Thanks
User avatar
phil
 
Posts: 19
Joined: Sat Mar 23, 2013 7:36 am
languages_spoken: english
ODROIDs: U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby Sahin » Tue Jun 18, 2013 5:02 pm

Is this kernel will work with arch linux?
Sahin
 
Posts: 1
Joined: Mon Feb 25, 2013 3:42 pm
languages_spoken: polish
ODROIDs: Odroid-U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Tue Jun 18, 2013 6:45 pm

Sahin wrote:Is this kernel will work with arch linux?


It will, but my script won't work for Arch :(

I've already talked to Arch developers to update their image :)
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby wpga » Tue Jun 18, 2013 7:39 pm

is it Temperature Logging working ?
thanks
User avatar
wpga
 
Posts: 17
Joined: Thu Feb 28, 2013 8:43 pm
languages_spoken: english, polish
ODROIDs: U2 overclocked to 2GHz running Linaro Xubuntu 12.11

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Tue Jun 18, 2013 7:43 pm

wpga wrote:is it Temperature Logging working ?
thanks


Yes.

Sent from my ODROID-Q2
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby wpga » Tue Jun 18, 2013 8:06 pm

"cat: /sys/devices/platform/tmu/temperature: No such file or directory"

am I doing something wrong ?
User avatar
wpga
 
Posts: 17
Joined: Thu Feb 28, 2013 8:43 pm
languages_spoken: english, polish
ODROIDs: U2 overclocked to 2GHz running Linaro Xubuntu 12.11

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Tue Jun 18, 2013 8:11 pm

/sys/devices/virtual/thermal/thermal_zone0/temp


Sent from my ODROID-Q2
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby wpga » Tue Jun 18, 2013 8:43 pm

thank you very much
User avatar
wpga
 
Posts: 17
Joined: Thu Feb 28, 2013 8:43 pm
languages_spoken: english, polish
ODROIDs: U2 overclocked to 2GHz running Linaro Xubuntu 12.11

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Tue Jun 18, 2013 10:48 pm

phil wrote:are you able to add MCEUSB Thanks


https://github.com/hardkernel/linux/com ... 17369af94c

Done :) next build will have it
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby Karamell » Wed Jun 19, 2013 1:31 am

Hi,
Thanks for that great work mdrjr !!! It saves us a lot of time recompiling the kernel.

Thank you a lot again
Karamell
 
Posts: 18
Joined: Wed May 15, 2013 1:01 am
languages_spoken: english
ODROIDs: X-2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby bobzibub » Thu Jun 20, 2013 1:09 am

Thank you so much for this kernel! I have an old DVI Dell monitor and it crashes with sound via DVI so this kernel is great!

I do have an issue where I cannot see my USB 2.0 (powered) hub. If I plug in peripherals in the ODROID (U2) itself they are registered but not via the hub. My plan is to plug a SATA drive via a USB adapter for some "big" storage. I suspect that it is a missing module but I'm not sure.

Code: Select all
[odroid@localhost ~]$ uname -a
Linux localhost.localdomain 3.8.13.2 #1 SMP PREEMPT Tue Jun 18 00:33:41 BRT 2013 armv7l armv7l armv7l GNU/Linux


The Logitech is a usb dongle for a wireless keyboard. That works great.

Code: Select all
[odroid@localhost ~]$ lsusb
Bus 001 Device 002: ID 0424:9730 Standard Microsystems Corp.
Bus 001 Device 003: ID 0424:3503 Standard Microsystems Corp.
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 004: ID 046d:c51e Logitech, Inc.

Any ideas?

Cheers,
b
bobzibub
 
Posts: 7
Joined: Thu Jun 20, 2013 1:00 am
languages_spoken: english
ODROIDs: U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Thu Jun 20, 2013 1:37 am

Tbh, Nope. I have not.. I won't call a missing module.. I do have a 7Port USB 2.0 Powered HUB that I use..
I have 2 SATA SSD's on external cases, 1 Webcam and 1 logitech Keyboard/Mouse connected..

It works very well on my U2.. I can double check for you later today.. but I almost certain that it was working fine.
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Linux Kernel 3.8.13.2 For Debian?

Unread postby Tuigje » Thu Jun 20, 2013 2:39 am

Hi,

My Odroid-X2 board just arrived, so I'm trying use the latest and greatest kernel.
Both this 3.8 kernel, and one cross-compiled from git (using odroidx2_defconfig) don't seem to boot on my system.
A cross-compiled 3.0 kernel works fine. I've tried the given .scr, and a modified one which skips the ramdisk.
Again, they work with 3.0, but not with 3.8

The rootfs is the debian U2 image, upgraded to debian-testing.

After booting 3.8, the first blue LED keeps pulsing two short blimps, with some pause inbetween.

Does someone have a hint on what I could do ?

Edit:
moved to http://forum.odroid.com/viewtopic.php?f=16&t=1554, as requested below.
Last edited by Tuigje on Thu Jun 20, 2013 4:58 am, edited 1 time in total.
Tuigje
 
Posts: 60
Joined: Thu Jun 20, 2013 1:00 am
languages_spoken: english dutch german
ODROIDs: Odroid X2

Re: Linux Kernel 3.8.13.2 For Debian?

Unread postby mdrjr » Thu Jun 20, 2013 4:41 am

Tuigje wrote:Hi,

My Odroid-X2 board just arrived, so I'm trying use the latest and greatest kernel.
Both this 3.8 kernel, and one cross-compiled from git (using odroidx2_defconfig) don't seem to boot on my system.
A cross-compiled 3.0 kernel works fine. I've tried the given .scr, and a modified one which skips the ramdisk.
Again, they work with 3.0, but not with 3.8

The rootfs is the debian U2 image, upgraded to debian-testing.

After booting 3.8, the first blue LED keeps pulsing two short blimps, with some pause inbetween.

Does someone have a hint on what I could do ?


Hi, First I'll ask you to not off-topic this thread, since its exclusive to Hardkernel Made images.
Please create your own thread about your issue and we'll take from there.
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby G[3z] » Thu Jun 20, 2013 9:01 am

mdrjr wrote:Do you use eMMC and SD at the same time ?

if so, try changing it for now, I'll check the initialization code for eMMC and SD.


i tried flashing without the sd card inside but nothing changed.
if i plug the sd after the odroid is booted it's impossible to reach the device.
if i boot with the sd card inserted it's recognized as BOOT.
wired :(
G[3z]
 
Posts: 7
Joined: Tue Jun 04, 2013 7:50 am
languages_spoken: italian english
ODROIDs: ODROID U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Thu Jun 20, 2013 9:04 am

G[3z] wrote:
mdrjr wrote:Do you use eMMC and SD at the same time ?

if so, try changing it for now, I'll check the initialization code for eMMC and SD.


i tried flashing without the sd card inside but nothing changed.
if i plug the sd after the odroid is booted it's impossible to reach the device.
if i boot with the sd card inserted it's recognized as BOOT.
wired :(


Not weird really.. Its because on kernel 3.8 for some reason the Initialization order of the eMMC/SD is swapped!
So you have to edit /etc/fstab and change /dev/mmcblk0p2 on /media/boot
to /dev/mmcblk1p2 on /media/boot
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby jimenez » Thu Jun 20, 2013 6:40 pm

Hi,

does the new kernel includes drivgers for other usb wifi dongles?
jimenez
 
Posts: 7
Joined: Thu Jun 13, 2013 11:48 pm
languages_spoken: english, spanish, german
ODROIDs: U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Thu Jun 20, 2013 6:47 pm

jimenez wrote:Hi,

does the new kernel includes drivgers for other usb wifi dongles?


Yes, for a lot of them in fact..
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby G[3z] » Fri Jun 21, 2013 4:39 am

mdrjr wrote:Not weird really.. Its because on kernel 3.8 for some reason the Initialization order of the eMMC/SD is swapped!
So you have to edit /etc/fstab and change /dev/mmcblk0p2 on /media/boot
to /dev/mmcblk1p2 on /media/boot


Image
i did what you suggested but now when i do open gparted i get an "I/O error while reading mmcblk0" (even if empty).
and if i put any microSD in the slot it doesn't appear in the desktop.
i guess i'll stick with 3.0.80 for a while
G[3z]
 
Posts: 7
Joined: Tue Jun 04, 2013 7:50 am
languages_spoken: italian english
ODROIDs: ODROID U2

Re: Linux Kernel 3.8.13.2 For Ubuntu/Fedora/OpenSUSE

Unread postby mdrjr » Fri Jun 21, 2013 4:50 am

you can't remove and re-insert a card once is probed..
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby Karamell » Sun Jun 23, 2013 7:27 am

Hi all,
I got a problem when installing software with ubuntu 13.04 : dpkg or apt-get could not find /boot/vmlinuz-XXX and initramfs-XXX
Found work-around :
Copy the ones ones from /media/F999XXXX (the ones installed by the script under the real booting area) to the /boot of the card and give them the proper name... it stops the complaint..

Maybe mdjr could adress that in next script release.. in the meanwhile, hope this helps newbies like me :-)
Karamell
 
Posts: 18
Joined: Wed May 15, 2013 1:01 am
languages_spoken: english
ODROIDs: X-2

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby mintz » Sun Jun 23, 2013 7:59 am

Can you add support for a USB2.0 to Ethernet adapter (link here)? I am in need of 2 ethernet port on my U2 and cannot get this adapter to work. There are different branches of these adapters available but I do believe they're using the same chip, thus the same drivers (http://www.win-star.com/download/Driver ... _V1.61.rar).

The adapter does work straight away with other devices, including my TV android stick so I guess it's just matter of compiling the driver and shove it in there somehow. Since I have no idea where to begin I just hope somebody can work their magic and get this adapter to work for me. I would be so very glad.
mintz
 
Posts: 27
Joined: Wed Feb 27, 2013 7:19 pm
languages_spoken: english
ODROIDs: ODROID U2

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby mdrjr » Sun Jun 23, 2013 8:09 am

Ah ASIX gb lan chipsets!

I already have this module build for 3.8... It should be working...

ASIX AX88xxx Based USB 2.0 Ethernet Adapters (USB_NET_AX8817X)

CONFIG_USB_NET_AX8817X:

This option adds support for ASIX AX88xxx based USB 2.0
10/100 Ethernet adapters.

This driver should work with at least the following devices:
* Aten UC210T
* ASIX AX88172
* Billionton Systems, USB2AR
* Buffalo LUA-U2-KTX
* Corega FEther USB2-TX
* D-Link DUB-E100
* Hawking UF200
* Linksys USB200M
* Netgear FA120
* Sitecom LN-029
* Intellinet USB 2.0 Ethernet
* ST Lab USB 2.0 Ethernet
* TrendNet TU2-ET100


Took from the driver that you linked:
Linux kernels 3.2 and later have support for this adapter built-in (with config USB_NET_AX8817X).


So, updating to 3.8 will enable it.. I can't guarantee since the documentation says it will work and the kernel module is there.
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby mintz » Mon Jun 24, 2013 12:18 am

I've updated to latest kernel but it doesn't work. The adapter doesn't lit like with Linaro 12.10 so I think it has something to do with the kernel for 13.04. Is there any log that I can pull for you?

Running the Ubuntu 13.04 server image for U2 by the way.
mintz
 
Posts: 27
Joined: Wed Feb 27, 2013 7:19 pm
languages_spoken: english
ODROIDs: ODROID U2

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby zinc » Mon Jun 24, 2013 12:29 am

I'm getting CMD23 timed out errors on boot when I use the 3.8 kernel on U2. It doesn't happen with the 3.0 kernel.

I have a Kingston 16 GB MicroSD card. I had to disable CMD23 support for it to work... any idea why I'm only seeing this on 3.8?

Code: Select all
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index cb3ab49..21056b9 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1267,7 +1267,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
         * We'll avoid using CMD23-bounded multiblock writes for
         * these, while retaining features like reliable writes.
         */
-/*     if ((md->flags & MMC_BLK_CMD23) && mmc_op_multi(brq->cmd.opcode) &&
+       if ((md->flags & MMC_BLK_CMD23) && mmc_op_multi(brq->cmd.opcode) &&
            (do_rel_wr || !(card->quirks & MMC_QUIRK_BLK_NO_CMD23) ||
             do_data_tag)) {
                brq->sbc.opcode = MMC_SET_BLOCK_COUNT;
@@ -1277,7 +1277,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
                brq->sbc.flags = MMC_RSP_R1 | MMC_CMD_AC;
                brq->mrq.sbc = &brq->sbc;
        }
-*/
+
        mmc_set_data_timeout(&brq->data, card);
 
        brq->data.sg = mqrq->sg;
zinc
 
Posts: 13
Joined: Mon Jun 24, 2013 12:02 am
languages_spoken: english
ODROIDs: ODROID-U2

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 24, 2013 12:38 am

zinc wrote:I'm getting CMD23 timed out errors on boot when I use the 3.8 kernel on U2. It doesn't happen with the 3.0 kernel.

I have a Kingston 16 GB MicroSD card. I had to disable CMD23 support for it to work... any idea why I'm only seeing this on 3.8?

Code: Select all
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index cb3ab49..21056b9 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1267,7 +1267,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
         * We'll avoid using CMD23-bounded multiblock writes for
         * these, while retaining features like reliable writes.
         */
-/*     if ((md->flags & MMC_BLK_CMD23) && mmc_op_multi(brq->cmd.opcode) &&
+       if ((md->flags & MMC_BLK_CMD23) && mmc_op_multi(brq->cmd.opcode) &&
            (do_rel_wr || !(card->quirks & MMC_QUIRK_BLK_NO_CMD23) ||
             do_data_tag)) {
                brq->sbc.opcode = MMC_SET_BLOCK_COUNT;
@@ -1277,7 +1277,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
                brq->sbc.flags = MMC_RSP_R1 | MMC_CMD_AC;
                brq->mrq.sbc = &brq->sbc;
        }
-*/
+
        mmc_set_data_timeout(&brq->data, card);
 
        brq->data.sg = mqrq->sg;


I don't take patchs like this, please submit a PR on github with error log.. and if its MMC2 errors.... :)
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 24, 2013 12:38 am

mintz wrote:I've updated to latest kernel but it doesn't work. The adapter doesn't lit like with Linaro 12.10 so I think it has something to do with the kernel for 13.04. Is there any log that I can pull for you?

Running the Ubuntu 13.04 server image for U2 by the way.


Yes, please the log when the script runs.
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby zinc » Mon Jun 24, 2013 12:44 am

mdrjr wrote:
zinc wrote:I'm getting CMD23 timed out errors on boot when I use the 3.8 kernel on U2. It doesn't happen with the 3.0 kernel.

I have a Kingston 16 GB MicroSD card. I had to disable CMD23 support for it to work... any idea why I'm only seeing this on 3.8?

Code: Select all
diff --git a/drivers/mmc/card/block.c b/drivers/mmc/card/block.c
index cb3ab49..21056b9 100644
--- a/drivers/mmc/card/block.c
+++ b/drivers/mmc/card/block.c
@@ -1267,7 +1267,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
         * We'll avoid using CMD23-bounded multiblock writes for
         * these, while retaining features like reliable writes.
         */
-/*     if ((md->flags & MMC_BLK_CMD23) && mmc_op_multi(brq->cmd.opcode) &&
+       if ((md->flags & MMC_BLK_CMD23) && mmc_op_multi(brq->cmd.opcode) &&
            (do_rel_wr || !(card->quirks & MMC_QUIRK_BLK_NO_CMD23) ||
             do_data_tag)) {
                brq->sbc.opcode = MMC_SET_BLOCK_COUNT;
@@ -1277,7 +1277,7 @@ static void mmc_blk_rw_rq_prep(struct mmc_queue_req *mqrq,
                brq->sbc.flags = MMC_RSP_R1 | MMC_CMD_AC;
                brq->mrq.sbc = &brq->sbc;
        }
-*/
+
        mmc_set_data_timeout(&brq->data, card);
 
        brq->data.sg = mqrq->sg;


I don't take patchs like this, please submit a PR on github with error log.. and if its MMC2 errors.... :)


Sorry, this isn't a patch you'd want to merge. It'd just a hack that works for me to disable CMD23 support altogether. I imagine there's a proper fix to the problem, I just don't know where to begin looking. If you have any hints or info on what might have changed with regards to SDMMC support between 3.0 or 3.8 (maybe PLL setup or controller drivers?) that would be great =)

Unfortunately, I don't have the equipment to check timings on the hardware side =/
zinc
 
Posts: 13
Joined: Mon Jun 24, 2013 12:02 am
languages_spoken: english
ODROIDs: ODROID-U2

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 24, 2013 12:47 am

is it mmc2 errors ?
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby zinc » Mon Jun 24, 2013 12:53 am

mdrjr wrote:is it mmc2 errors ?


Wow, you're fast =)

Boot log

Code: Select all
U-Boot 2010.12-svn (Dec 21 2012 - 19:44:04) for Exynox4412


CPU: S5PC220 [Samsung SOC on SMP Platform Base on ARM CortexA9]
APLL = 1000MHz, MPLL = 880MHz
DRAM:  2047 MiB

PMIC VERSION : 0x00, CHIP REV : 2
TrustZone Enabled BSP
BL1 version: 20121128


Checking Boot Mode ... SDMMC
MMC Device 0: 15292 MB
MMC Device 1 not found
ModeKey Check... run normal_boot
Net:   No ethernet found.
Hit any key to stop autoboot:  0
>>> Load Boot Script from mmc 0:1 <<<
Partition1: Start Address(0x1000), Size(0x40000)
reading boot.scr
Warning : Reads a file that is smaller than the cluster size.

484 bytes read
## Executing script at 40008000
Partition1: Start Address(0x1000), Size(0x40000)
reading zImage

2316480 bytes read
Partition1: Start Address(0x1000), Size(0x40000)
reading uInitrd

2789551 bytes read
Boot with zImage
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   uInitrd 3.8.13.2
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    2789487 Bytes = 2724 KiB
   Load Address: 00000000
   Entry Point:  00000000

Starting kernel ...

Uncompressing Linux... done, booting the kernel.
[    0.000000] Booting Linux on physical CPU 0xa00
[    0.000000] Initializing cgroup subsys cpuset
[    0.000000] Linux version 3.8.13.3 (git@m1builder) (gcc version 4.7.3 20121205 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2012.12-20121214 - Linaro GCC 2012.12) ) #1 SMP PREEMPT Sun Jun 23 00:41:44 BRT 2013 ()
[    0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] Machine: ODROIDU2
[    0.000000] cma: CMA: reserved 8 MiB at 43000000
[    0.000000] cma: CMA: reserved 8 MiB at 51000000
[    0.000000] cma: CMA: reserved 32 MiB at 6d800000
[    0.000000] Memory policy: ECC disabled, Data cache writealloc
[    0.000000] CPU EXYNOS4412 (id 0xe4412220)
[    0.000000] S3C24XX Clocks, Copyright 2004 Simtec Electronics
[    0.000000] s3c_register_clksrc: clock armclk has no registers set
[    0.000000] s3c_register_clksrc: clock audiocdclk has no registers set
[    0.000000] audiocdclk: no parent clock specified
[    0.000000] EXYNOS4: PLL settings, A=1000000000, M=880000000, E=96000000 V=350000000
[    0.000000] EXYNOS4: ARMCLK=1000000000, DMC=440000000, ACLK200=176000000
[    0.000000] ACLK100=110000000, ACLK160=176000000, ACLK133=146666666
[    0.000000] sclk_pwm: source is ext_xtal (0), rate is 24000000
[    0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_csis: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_cam0: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_cam1: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimc: source is xusbxti (1), rate is 1500000
[    0.000000] sclk_fimd: source is mout_mpll_user (6), rate is 55000000
[    0.000000] sclk_mfc: source is mout_mfc0 (0), rate is 55000000
[    0.000000] sclk_g3d: source is mout_g3d0 (0), rate is 55000000
[    0.000000] Running under secure firmware.
[    0.000000] PERCPU: Embedded 7 pages/cpu @c1675000 s7936 r8192 d12544 u32768
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 519938
[    0.000000] Kernel command line: console=tty1 console=ttySAC1,115200 mem=2047M console=tty1 console=ttySAC1,115200n8 hdtv_type=hdmi hdtv_format=720p60hz root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro mem=2047M
[    0.000000] s5p-tv: HDTV TYPE is hdmi
[    0.000000] s5p-tv: HDTV FORMAT is 720p60hz
[    0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.000000] __ex_table already sorted, skipping sort
[    0.000000] Memory: 2047MB = 2047MB total
[    0.000000] Memory: 2020192k/4040384k available, 151872k reserved, 1317888K highmem
[    0.000000] Virtual kernel memory layout:
[    0.000000]     vector  : 0xffff0000 - 0xffff1000   (   4 kB)
[    0.000000]     fixmap  : 0xfff00000 - 0xfffe0000   ( 896 kB)
[    0.000000]     vmalloc : 0xf0000000 - 0xff000000   ( 240 MB)
[    0.000000]     lowmem  : 0xc0000000 - 0xef800000   ( 760 MB)
[    0.000000]     pkmap   : 0xbfe00000 - 0xc0000000   (   2 MB)
[    0.000000]     modules : 0xbf000000 - 0xbfe00000   (  14 MB)
[    0.000000]       .text : 0xc0008000 - 0xc059625c   (5689 kB)
[    0.000000]       .init : 0xc0597000 - 0xc05c0f00   ( 168 kB)
[    0.000000]       .data : 0xc05c2000 - 0xc0624700   ( 394 kB)
[    0.000000]        .bss : 0xc0624700 - 0xc065f910   ( 237 kB)
[    0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] Preemptible hierarchical RCU implementation.
[    0.000000] NR_IRQS:549
[    0.000000] sched_clock: 32 bits at 200 Hz, resolution 5000000ns, wraps every 4294967291ms
[    0.000000] Console: colour dummy device 80x30
[    0.000000] console [tty1] enabled
[    0.045000] Calibrating delay loop... 1992.29 BogoMIPS (lpj=4980736)
[    0.045000] pid_max: default: 32768 minimum: 301
[    0.045000] Mount-cache hash table entries: 512
[    0.045000] Initializing cgroup subsys cpuacct
[    0.045000] Initializing cgroup subsys devices
[    0.045000] CPU: Testing write buffer coherency: ok
[    0.045000] CPU0: thread -1, cpu 0, socket 10, mpidr 80000a00
[    0.045000] Setting up static identity map for 0x4041f248 - 0x4041f2a0
[    0.045000] L310 cache controller enabled
[    0.045000] l2x0: 16 ways, CACHE_ID 0x4100c4c8, AUX_CTRL 0x7e470001, Cache size: 1048576 B
[    0.075000] CPU1: Booted secondary processor
[    0.095000] CPU1: thread -1, cpu 1, socket 10, mpidr 80000a01
[    0.105000] CPU2: Booted secondary processor
[    0.125000] CPU2: thread -1, cpu 2, socket 10, mpidr 80000a02
[    0.135000] CPU3: Booted secondary processor
[    0.155000] CPU3: thread -1, cpu 3, socket 10, mpidr 80000a03
[    0.155000] Brought up 4 CPUs
[    0.155000] SMP: Total of 4 processors activated (7969.17 BogoMIPS).
[    0.155000] devtmpfs: initialized
[    0.160000] regulator-dummy: no parameters
[    0.160000] NET: Registered protocol family 16
[    0.170000] DMA: preallocated 256 KiB pool for atomic coherent allocations
[    0.180000] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[    0.180000] hw-breakpoint: maximum watchpoint size is 4 bytes.
[    0.180000] S3C Power Management, Copyright 2004 Simtec Electronics
[    0.180000] EXYNOS4x12 PMU Initialize
[    0.180000] EXYNOS: Initializing architecture
[    0.180000] s3c24xx-pwm s3c24xx-pwm.0: tin at 110000000, tdiv at 110000000, tin=divclk, base 0
[    0.180000] s3c24xx-pwm s3c24xx-pwm.1: tin at 110000000, tdiv at 110000000, tin=divclk, base 8
[    0.195000] bio: create slab <bio-0> at 0
[    0.195000] hdmi_5v: 5000 mV
[    0.195000] usbcore: registered new interface driver usbfs
[    0.195000] usbcore: registered new interface driver hub
[    0.195000] usbcore: registered new device driver usb
[    0.195000] s3c-i2c s3c2440-i2c.0: slave address 0x10
[    0.195000] s3c-i2c s3c2440-i2c.0: bus frequency set to 71 KHz
[    0.200000] max77686 0-0009: device found
[    0.200000] max77686 0-0009: irq is not specified
[    0.225000] LDO1 VDD_ALIVE: 1000 mV
[    0.255000] LDO2 VDDQ_M1_1V8: 1200 mV
[    0.285000] LDO3 VDDQ_AUD_1V8: 1800 mV
[    0.315000] LDO4 VDDQ_MMC2_2V8: 2800 mV
[    0.345000] LDO5 VDDQ_MMC1_1V8: 1800 mV
[    0.375000] LDO6 VDD10_MPLL_1V0: 1000 mV
[    0.405000] LDO7 VDD10_EPLL_1V0: 1000 mV
[    0.435000] LDO8 VDD10_MIPI_1V0: 1000 mV
[    0.460000] LDO9 VT_CORE_1V0: ODROIDU2: Disabled regulator
[    0.460000] LDO9 VT_CORE_1V0: 1000 mV
[    0.475000] LDO10 VDD18_MIPI_1V8: 1800 mV
[    0.505000] LDO11 VDD18_ABB1_1V8: 1800 mV
[    0.520000] vdd_ldo12 range: 3300 mV
[    0.550000] LDO13 VDD18_MIPIHSI_1V8: 1800 mV
[    0.580000] LDO14 VDD18_ADC_1V8: 1800 mV
[    0.595000] vdd_ldo15 range: 1000 mV
[    0.625000] LDO16 VDD18_HSIC: 1800 mV
[    0.655000] LDO17 VDDQ_CAM_1V8: 1800 mV
[    0.680000] LDO18 VDDQ_ISP_1V8: ODROIDU2: Disabled regulator
[    0.680000] LDO18 VDDQ_ISP_1V8: 1800 mV
[    0.690000] LDO19 VT_CAM_1V8: ODROIDU2: Disabled regulator
[    0.690000] LDO19 VT_CAM_1V8: 1800 mV
[    0.705000] LDO20 EMMC_IO_1V8: 1800 mV
[    0.735000] LDO21 TFLASH_2V8: 2800 mV
[    0.765000] LDO22 2V8: 2800 mV
[    0.790000] LDO23 VDD_TOUCH_2V8: ODROIDU2: Disabled regulator
[    0.790000] LDO23 VDD_TOUCH_2V8: 2800 mV
[    0.815000] LDO24 VDD_TOUCHLED_3V3: ODROIDU2: Disabled regulator
[    0.815000] LDO24 VDD_TOUCHLED_3V3: 3300 mV
[    0.845000] LDO25 VDDQ_LCD_3V0: 1800 mV
[    0.870000] LDO26 VDD_MOTOR_3V0: ODROIDU2: Disabled regulator
[    0.870000] LDO26 VDD_MOTOR_3V0: 3000 mV
[    0.880000] BUCK1 vdd_mif: 1100 mV
[    0.895000] BUCK2 vdd_arm: 800 <--> 1500 mV at 1450 mV
[    0.905000] BUCK3 vdd_int: 1125 mV
[    0.920000] BUCK4 vdd_g3d: 850 <--> 1200 mV at 1075 mV
[    0.950000] BUCK5 VDDQ_CKEM1_2: 1200 mV
[    0.980000] BUCK6 1V35: 1350 mV
[    1.010000] BUCK7 2V0: 2000 mV
[    1.025000] ODROIDU2: Regulator BUCK8
[    1.175000] BUCK8 3V0: 3300 mV
[    1.200000] BUCK9 1V2: ODROIDU2: Disabled regulator
[    1.200000] BUCK9 1V2: 1200 mV
[    1.205000] s3c-i2c s3c2440-i2c.0: i2c-0: S3C I2C adapter
[    1.205000] s3c-i2c s3c2440-i2c.1: slave address 0x10
[    1.205000] s3c-i2c s3c2440-i2c.1: bus frequency set to 71 KHz
[    1.205000] s3c-i2c s3c2440-i2c.1: i2c-1: S3C I2C adapter
[    1.205000] s3c-i2c s3c2440-i2c.3: slave address 0x10
[    1.205000] s3c-i2c s3c2440-i2c.3: bus frequency set to 71 KHz
[    1.205000] s3c-i2c s3c2440-i2c.3: i2c-3: S3C I2C adapter
[    1.205000] s3c-i2c s3c2440-i2c.7: slave address 0x10
[    1.205000] s3c-i2c s3c2440-i2c.7: bus frequency set to 71 KHz
[    1.205000] s3c-i2c s3c2440-i2c.7: i2c-7: S3C I2C adapter
[    1.205000] s3c-i2c s3c2440-hdmiphy-i2c: slave address 0x10
[    1.205000] s3c-i2c s3c2440-hdmiphy-i2c: bus frequency set to 71 KHz
[    1.205000] s3c-i2c s3c2440-hdmiphy-i2c: i2c-8: S3C I2C adapter
[    1.205000] Linux video capture interface: v2.00
[    1.205000] Advanced Linux Sound Architecture Driver Initialized.
[    1.205000] cfg80211: Calling CRDA to update world regulatory domain
[    1.205000] Switching to clocksource mct-frc
[    1.215000] NET: Registered protocol family 2
[    1.215000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    1.215000] TCP bind hash table entries: 8192 (order: 5, 163840 bytes)
[    1.215000] TCP: Hash tables configured (established 8192 bind 8192)
[    1.215000] TCP: reno registered
[    1.215000] UDP hash table entries: 512 (order: 2, 24576 bytes)
[    1.215000] UDP-Lite hash table entries: 512 (order: 2, 24576 bytes)
[    1.215000] NET: Registered protocol family 1
[    1.215000] Trying to unpack rootfs image as initramfs...
[    1.360000] Freeing initrd memory: 2724K
[    1.365000] CPU PMU: probing PMU on CPU 3
[    1.365000] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[    1.365000] bounce pool size: 64 pages
[    1.375000] msgmni has been set to 1473
[    1.375000] io scheduler noop registered
[    1.375000] io scheduler deadline registered
[    1.375000] io scheduler cfq registered (default)
[    1.385000] s3c-fb exynos4-fb.0: start latency exceeded, new value 667 ns
[    1.385000] s3c-fb exynos4-fb.0: state restore latency exceeded, new value 32000 ns
[    1.405000] Console: switching to colour frame buffer device 170x48
[    1.410000] s3c-fb exynos4-fb.0: window 0: fb
[    1.415000] dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056
[    1.415000] dma-pl330 dma-pl330.0:    DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.420000] dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056
[    1.420000] dma-pl330 dma-pl330.1:    DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    1.425000] dma-pl330 dma-pl330.2: Loaded driver for PL330 DMAC-267056
[    1.425000] dma-pl330 dma-pl330.2:    DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    1.495000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    1.495000] exynos4210-uart.0: ttySAC0 at MMIO 0x13800000 (irq = 84) is a S3C6400/10
[    1.495000] exynos4210-uart.1: ttySAC1 at MMIO 0x13810000 (irq = 85) is a S3C6400/10
[    2.495000] console [ttySAC1] enabled
[    2.495000] exynos4210-uart.2: ttySAC2 at MMIO 0x13820000 (irq = 86) is a S3C6400/10
[    2.505000] exynos4210-uart.3: ttySAC3 at MMIO 0x13830000 (irq = 87) is a S3C6400/10
[    2.515000] [drm] Initialized drm 1.1.0 20060810
[    2.520000] Mali<2>: Inserting Mali v19 device driver.
[    2.525000] Mali<2>: Compiled: Jun 23 2013, time: 00:38:59.
[    2.530000] Mali<2>: Driver revision:
[    2.535000] Mali<2>: mali_module_init() registering driver
[    2.540000] Mali<2>: mali_probe(): Called for platform device mali-utgard
[    2.545000] Mali<2>: Memory system initializing
[    2.550000] Mali<2>: Using device defined memory settings (dedicated: 0x00000000@0x00000000, shared: 0x10000000)
[    2.560000] Mali<2>: Mali OS memory allocator created with max allocation size of 0x10000000 bytes, cpu_usage_adjust 0x00000000
[    2.575000] Mali<2>: Using device defined frame buffer settings (0x00000000@0x00000000)
[    2.580000] mali-utgard mali-utgard.0: start latency exceeded, new value 583 ns
[    2.590000] mali-utgard mali-utgard.0: state restore latency exceeded, new value 3334 ns
[    2.595000] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[    2.600000] Mali<2>: Mali PP: Base address of PP core: 0x13008000
[    2.610000] Mali<2>: Found Mali GPU Mali-400 MP r1p1
[    2.615000] Mali<2>: Mali L2 cache: Creating Mali L2 cache: Mali_L2
[    2.620000] Mali<2>: Mali MMU: Creating Mali MMU: Mali_GP_MMU
[    2.625000] Mali<2>: Mali GP: Creating Mali GP core: Mali_GP
[    2.630000] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP0_MMU
[    2.635000] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP0
[    2.640000] Mali<2>: Mali PP: Base address of PP core: 0x13008000
[    2.650000] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP1_MMU
[    2.655000] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP1
[    2.660000] Mali<2>: Mali PP: Base address of PP core: 0x1300a000
[    2.665000] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP2_MMU
[    2.670000] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP2
[    2.675000] Mali<2>: Mali PP: Base address of PP core: 0x1300c000
[    2.685000] Mali<2>: Mali MMU: Creating Mali MMU: Mali_PP3_MMU
[    2.690000] Mali<2>: Mali PP: Creating Mali PP core: Mali_PP3
[    2.695000] Mali<2>: Mali PP: Base address of PP core: 0x1300e000
[    2.700000] Mali<2>: 4+0 PP cores initialized
[    2.705000] Mali<2>: Mali GPU Utilization: No utilization handler installed
[    2.715000] Mali<2>: mali_probe(): Successfully initialized driver for platform device mali-utgard
[    2.720000] mali-utgard mali-utgard.0: stop latency exceeded, new value 959 ns
[    2.730000] mali-utgard mali-utgard.0: state save latency exceeded, new value 4625 ns
[    2.735000] Mali: Mali device driver loaded
[    2.740000] UMP: UMP device driver  loaded
[    2.750000] brd: module loaded
[    2.760000] loop: module loaded
[    2.760000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    2.765000] s5p-ehci s5p-ehci: S5P EHCI Host Controller
[    2.770000] s5p-ehci s5p-ehci: new USB bus registered, assigned bus number 1
[    2.780000] s5p-ehci s5p-ehci: irq 102, io mem 0x12580000
[    2.795000] s5p-ehci s5p-ehci: USB 2.0 started, EHCI 1.00
[    2.795000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[    2.800000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.810000] usb usb1: Product: S5P EHCI Host Controller
[    2.815000] usb usb1: Manufacturer: Linux 3.8.13.3 ehci_hcd
[    2.820000] usb usb1: SerialNumber: s5p-ehci
[    2.825000] hub 1-0:1.0: USB hub found
[    2.830000] hub 1-0:1.0: 3 ports detected
[    2.830000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    2.840000] exynos-ohci exynos-ohci: Already power on PHY
[    2.845000] exynos-ohci exynos-ohci: EXYNOS OHCI Host Controller
[    2.850000] exynos-ohci exynos-ohci: new USB bus registered, assigned bus number 2
[    2.855000] exynos-ohci exynos-ohci: irq 102, io mem 0x12590000
[    2.920000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[    2.925000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.935000] usb usb2: Product: EXYNOS OHCI Host Controller
[    2.940000] usb usb2: Manufacturer: Linux 3.8.13.3 ohci_hcd
[    2.945000] usb usb2: SerialNumber: exynos-ohci
[    2.950000] hub 2-0:1.0: USB hub found
[    2.950000] hub 2-0:1.0: 3 ports detected
[    3.060000] usb3503 0-0008: switched to HUB mode
[    3.065000] usb3503 0-0008: usb3503_probe: probed on  hub mode
[    3.070000] s3c-rtc s3c64xx-rtc: rtc core: registered s3c as rtc0
[    3.075000] s5p-mfc s5p-mfc: decoder registered as /dev/video0
[    3.080000] s5p-mfc s5p-mfc: encoder registered as /dev/video1
[    3.085000] s5p-hdmiphy 8-0038: probe successful
[    3.090000] s5p-tv: Board is ODROID-X/X2/U2
[    3.095000] s5p-hdmi exynos4-hdmi: probe successful
[    3.100000] Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd.
[    3.100000]
[    3.110000] s5p-mixer s5p-mixer: probe start
[    3.115000] s5p-mixer s5p-mixer: resources acquired
[    3.115000] s5p-mixer s5p-mixer: added output 'S5P HDMI connector' from module 's5p-hdmi'
[    3.125000] s5p-mixer s5p-mixer: module s5p-sdo is missing
[    3.130000] s5p-mixer s5p-mixer: registered layer graph0 as /dev/video2
[    3.140000] fb1: registered frame buffer emulation for /dev/video2
[    3.145000] s5p-mixer s5p-mixer: registered layer graph1 as /dev/video3
[    3.145000] usb 1-2: new high-speed USB device number 2 using s5p-ehci
[    3.155000] fb2: registered frame buffer emulation for /dev/video3
[    3.165000] s5p-mixer s5p-mixer: registered layer video0 as /dev/video4
[    3.170000] fb3: registered frame buffer emulation for /dev/video4
[    3.175000] s5p-mixer s5p-mixer: probe successful
[    3.180000] s5p-g2d s5p-g2d.0: device registered as /dev/video5
[    3.185000] Exynos: Kernel Thermal management registered
[    3.190000] cpuidle: using governor ladder
[    3.195000] sdhci: Secure Digital Host Controller Interface driver
[    3.200000] sdhci: Copyright(c) Pierre Ossman
[    3.205000] s3c-sdhci exynos4-sdhci.2: clock source 2: mmc_busclk.2 (55000000 Hz)
[    3.215000] mmc0: no vqmmc regulator found
[    3.220000] mmc0: no vmmc regulator found
[    3.250000] mmc0: SDHCI controller on samsung-hsmmc [exynos4-sdhci.2] using ADMA
[    3.255000] dw_mmc dw_mmc: Using internal DMA controller.
[    3.255000] mmc1: no vmmc regulator found
[    3.280000] mmc0: new high speed SDHC card at address 0002
[    3.285000] mmcblk0: mmc0:0002 SD16G 14.9 GiB
[    3.290000] usb 1-2: New USB device found, idVendor=0424, idProduct=9730
[    3.290000] usb 1-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[    3.300000] dw_mmc dw_mmc: Version ID is 240a
[    3.300000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.300000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] end_request: I/O error, dev mmcblk0, sector 0
[    3.305000] Buffer I/O error on device mmcblk0, logical block 0
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.305000] end_request: I/O error, dev mmcblk0, sector 0
[    3.305000] Buffer I/O error on device mmcblk0, logical block 0
[    3.305000]  mmcblk0: unable to read partition table
[    3.305000] DWMMC: Div 2 = 125
[    3.305000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[    3.440000] dw_mmc dw_mmc: DW MMC controller at irq 109, 32 bit host data width, 128 deep fifo
[    3.450000] usbcore: registered new interface driver usbhid
[    3.455000] usbhid: USB HID core driver
[    3.490000] DWMMC: Div 1 = 167
[    3.490000] max98090 1-0010: revision 0x41
[    3.495000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 300000Hz, actual 299401HZ div = 167)
[    3.495000]    [MAX98090] max98090_set_record_main_mic(150)
[    3.510000] hkdk-snd-max89090 hkdk-snd-max89090:  max98090-aif1 <-> samsung-i2s.0 mapping ok
[    3.515000] hkdk-snd-max89090 hkdk-snd-max89090:  max98090-aif1 <-> samsung-i2s.0 mapping ok
[    3.525000] TCP: cubic registered
[    3.530000] NET: Registered protocol family 17
[    3.530000] NET: Registered protocol family 15
[    3.535000] NET: Registered protocol family 35
[    3.540000] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[    3.550000] ThumbEE CPU extension supported.
[    3.550000] Registering SWP/SWPB emulation handler
[    3.560000] BUCK4 vdd_g3d: incomplete constraints, leaving on
[    3.565000] LDO20 EMMC_IO_1V8: incomplete constraints, leaving on
[    3.570000] DWMMC: Div 2 = 250
[    3.570000] LDO10 VDD18_MIPI_1V8: incomplete constraints, leaving on
[    3.570000] DRM: mali_platform_drm_probe()
[    3.570000] mali_drm_init(), driver name: mali_drm, version 0.1
[    3.570000] DRM: mali_driver_load()
[    3.570000] [drm] Initialized mali_drm 0.1.0 20100520 on minor 0
[    3.595000] s3c-rtc s3c64xx-rtc: setting system clock to 2013-06-23 15:51:00 UTC (1372002660)
[    3.595000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 200000Hz, actual 200000HZ div = 250)
[    3.620000] exynos4_dvfs_hotplug_init, max(2000000),min(0)
[    3.620000] ALSA device list:
[    3.625000]   #0: Built-in Audio
[    3.625000] Freeing init memory: 164K
[    3.640000] usb 1-3: new high-speed USB device number 3 using s5p-ehci
Loading, please wait...
[    3.665000] udevd[1303]: starting version 175
Begin: Loading essential drivers ... done.
[    3.680000] DWMMC: Div 1 = 255
[    3.680000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 196079Hz, actual 196078HZ div = 255)
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
[    3.710000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.715000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.720000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.730000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.735000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.745000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.755000] end_request: I/O error, dev mmcblk0, sector 31317888
[    3.760000] Buffer I/O error on device mmcblk0, logical block 3914736
[    3.760000] DWMMC: Div 2 = 125
[    3.760000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 400000Hz, actual 400000HZ div = 125)
[    3.780000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.785000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.795000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.800000] usb 1-3: New USB device found, idVendor=0424, idProduct=3503
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] end_request: I/O error, dev mmcblk0, sector 31317888
[    3.805000] Buffer I/O error on device mmcblk0, logical block 3914736
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] end_request: I/O error, dev mmcblk0, sector 31318000
[    3.805000] Buffer I/O error on device mmcblk0, logical block 3914750
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] end_request: I/O error, dev mmcblk0, sector 31318000
[    3.805000] Buffer I/O error on device mmcblk0, logical block 3914750
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] end_request: I/O error, dev mmcblk0, sector 0
[    3.805000] Buffer I/O error on device mmcblk0, logical block 0
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] end_request: I/O error, dev mmcblk0, sector 0
[    3.805000] Buffer I/O error on device mmcblk0, logical block 0
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] end_request: I/O error, dev mmcblk0, sector 8
[    3.805000] Buffer I/O error on device mmcblk0, logical block 1
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] end_request: I/O error, dev mmcblk0, sector 31318008
[    3.805000] Buffer I/O error on device mmcblk0, logical block 3914751
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.805000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.810000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.810000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.810000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.810000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.810000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
... (snip, same text repeated)
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.840000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.845000] DWMMC: Div 1 = 167
[    3.845000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 300000Hz, actual 299401HZ div = 167)
[    3.845000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.845000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
... snip (same text repeated)
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.880000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.885000] mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
[    3.900000] DWMMC: Div 2 = 250
[    3.900000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 200000Hz, actual 200000HZ div = 250)
[    3.965000] DWMMC: Div 1 = 255
[    3.965000] mmc_host mmc1: Bus speed (slot 0) = 100000000Hz (slot req 196079Hz, actual 196078HZ div = 255)
[    9.500000]    [MAX98090] max98090_set_playback_speaker_headset(111)
[   10.625000] usb 1-3: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[   10.635000] hub 1-3:1.0: USB hub found
[   10.635000] hub 1-3:1.0: 3 ports detected
[   10.925000] usb 1-3.3: new full-speed USB device number 4 using s5p-ehci
[   11.030000] usb 1-3.3: New USB device found, idVendor=046d, idProduct=c52b
[   11.035000] usb 1-3.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[   11.040000] usb 1-3.3: Product: USB Receiver
[   11.045000] usb 1-3.3: Manufacturer: Logitech
Gave up waiting for root device.  Common problems:
 - Boot args (cat /proc/cmdline)
   - Check rootdelay= (did the system wait long enough?)
   - Check root= (did the system wait for the right device?)
 - Missing modules (cat /proc/modules; ls /dev)
ALERT!  /dev/disk/by-uuid/e139ce78-9841-40fe-8823-96a304a09859 does not exist.  Dropping to a shell!


BusyBox v1.20.2 (Ubuntu 1:1.20.0-8ubuntu1) built-in shell (ash)
Enter 'help' for a list of built-in commands.

(initramfs)
zinc
 
Posts: 13
Joined: Mon Jun 24, 2013 12:02 am
languages_spoken: english
ODROIDs: ODROID-U2

Re: Linux Kernel 3.8.13.3 For Ubuntu(Server)/Fedora/OpenSUSE

Unread postby mdrjr » Mon Jun 24, 2013 1:00 am

ehh.. Check your card.. something is wrong with it :)
mdrjr
Site Admin
 
Posts: 11663
Joined: Fri Feb 22, 2013 11:34 pm
Location: Brazil
languages_spoken: english, portuguese
ODROIDs: -

Next

Return to News

Who is online

Users browsing this forum: No registered users and 2 guests