[SOLVED] HARDWARE PROTECTION shutdown (Temperature too high)

Post Reply
matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

[SOLVED] HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

I want to try the Image ubuntu 6.1 minimal. The image with kernel 5.4 minimal works correctly.
The 6.1 kernel gives mei a Temperature too high an shutdown the system.
Here is the complete Log. What can i do, to fix the problem?

Code: Select all

[00]

U-Boot 2017.05-00008-g6a9ddb8303-dirty (May 19 2020 - 19:48:01 +0900) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz
Model: Odroid XU4 based on EXYNOS5422
Board: Odroid XU4 based on EXYNOS5422
Type:  xu4
DRAM:  2 GiB
MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
MMC Device 0 ( SD ): 58.2 GiB
mmc_init: -5, time 4
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Press quickly 'Enter' twice to stop autoboot:  0 
reading /boot.ini
2365 bytes read in 4 ms (577.1 KiB/s)
## Executing script at 43e00000
reading config.ini
6911 bytes read in 5 ms (1.3 MiB/s)
ini: Imported macaddr as 00:1e:06:61:7a:39
ini: Imported vout as hdmi
ini: Imported HPD as true
ini: Imported cecenable as false
ini: Imported disable_vu7 as false
ini: Imported ddr_freq as 825
ini: Imported overlay_resize as 16384
ini: Imported overlay_profile as 
ini: Imported overlays as spi0 i2c0 i2c1 uart0
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
reading zImage
7093416 bytes read in 476 ms (14.2 MiB/s)
reading uInitrd
8446708 bytes read in 566 ms (14.2 MiB/s)
reading exynos5422-odroidxu4.dtb
88459 bytes read in 13 ms (6.5 MiB/s)
reading overlays/spi0.dtbo
691 bytes read in 7 ms (95.7 KiB/s)
reading overlays/i2c0.dtbo
224 bytes read in 6 ms (36.1 KiB/s)
reading overlays/i2c1.dtbo
226 bytes read in 7 ms (31.3 KiB/s)
reading overlays/uart0.dtbo
227 bytes read in 6 ms (36.1 KiB/s)
Kernel image @ 0x40008000 [ 0x000000 - 0x6c3ca8 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8446644 Bytes = 8.1 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 44000000
   Booting using the fdt blob at 0x44000000
   reserving fdt memory region: addr=44000000 size=2c000
   Using Device Tree in place at 44000000, end 4402efff

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 6.1.45-7 (root@builder32) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #1 SMP PREEMPT Wed Aug 16 15:15:01 UTC 2023
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel ODROID XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0x00000000b6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000040000000-0x000000006fffffff]
[    0.000000]   HighMem  [mem 0x0000000070000000-0x00000000be9fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Running under secure firmware.
[    0.000000] percpu: Embedded 17 pages/cpu s39124 r8192 d22316 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false
[    0.000000] hdmi: using HDMI mode
[    0.000000] Unknown kernel command line parameters "false HPD=true vout=hdmi", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1895428K/2074624K available (12288K kernel code, 1123K rwdata, 2912K rodata, 2048K init, 362K bss, 48124K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000030] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57
[    0.001538] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.001561] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.001581] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001598] Ignoring duplicate/late registration of read_current_timer delay
[    0.002399] Console: colour dummy device 80x30
[    0.003162] printk: console [tty1] enabled
[    0.003227] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003274] CPU: Testing write buffer coherency: ok
[    0.003361] pid_max: default: 32768 minimum: 301
[    0.003511] LSM: Security Framework initializing
[    0.003704] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003758] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005525] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.006949] cblist_init_generic: Setting adjustable number of callback queues.
[    0.006994] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007185] cblist_init_generic: Setting adjustable number of callback queues.
[    0.007220] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007426] Setting up static identity map for 0x40200000 - 0x40200060
[    0.007780] ARM CCI driver probed
[    0.008365] Exynos MCPM support installed
[    0.008770] rcu: Hierarchical SRCU implementation.
[    0.008796] rcu: 	Max phase no-delay instances is 1000.
[    0.010111] smp: Bringing up secondary CPUs ...
[    0.011270] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.012566] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.013787] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.014985] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.015003] CPU4: detected I-Cache line size mismatch, workaround enabled
[    0.015011] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.015103] CPU4: Spectre BHB: enabling loop workaround for all CPUs
[    0.016392] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.016406] CPU5: detected I-Cache line size mismatch, workaround enabled
[    0.016414] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.017742] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.017756] CPU6: detected I-Cache line size mismatch, workaround enabled
[    0.017764] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.019042] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.019056] CPU7: detected I-Cache line size mismatch, workaround enabled
[    0.019064] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.019304] smp: Brought up 1 node, 8 CPUs
[    0.019367] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.019396] CPU: All CPU(s) started in HYP mode.
[    0.019416] CPU: Virtualization extensions available.
[    0.020884] devtmpfs: initialized
[    0.041506] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.041784] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.041826] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.044928] pinctrl core: initialized pinctrl subsystem
[    0.047878] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.051582] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.053236] audit: initializing netlink subsys (disabled)
[    0.053521] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1
[    0.054088] thermal_sys: Registered thermal governor 'step_wise'
[    0.054363] cpuidle: using governor menu
[    0.054837] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.054867] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.195863] EXYNOS5420 PMU initialized
[    0.322453] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.324404] fbcon: Taking over console
[    0.326168] iommu: Default domain type: Translated 
[    0.326192] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.326602] usbcore: registered new interface driver usbfs
[    0.326669] usbcore: registered new interface driver hub
[    0.326738] usbcore: registered new device driver usb
[    0.327456] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.327487] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.327819] s3c-i2c 12c70000.i2c: i2c-0: S3C I2C adapter
[    0.328041] s3c-i2c 12c80000.i2c: slave address 0x00
[    0.328070] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[    0.328379] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[    0.328869] mc: Linux media interface: v0.10
[    0.328921] videodev: Linux video capture interface: v2.00
[    0.329517] Advanced Linux Sound Architecture Driver Initialized.
[    0.330562] clocksource: Switched to clocksource mct-frc
[    0.331029] VFS: Disk quotas dquot_6.6.0
[    0.331106] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.344425] NET: Registered PF_INET protocol family
[    0.344690] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.346522] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.346572] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.346607] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.346762] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.347065] TCP: Hash tables configured (established 8192 bind 8192)
[    0.347189] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.347250] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.347503] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.347570] NET: Registered PF_XDP protocol family
[    0.348142] Trying to unpack rootfs image as initramfs...
[    0.360774] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.361931] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.364016] Initialise system trusted keyrings
[    0.364366] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.373744] ksmbd: The ksmbd server is experimental
[    0.373777] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.462650] Key type asymmetric registered
[    0.462686] Asymmetric key parser 'x509' registered
[    0.462951] bounce: pool size: 64 pages
[    0.463105] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.463425] io scheduler mq-deadline registered
[    0.463454] io scheduler kyber registered
[    0.463713] io scheduler bfq registered
[    0.467687] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator
[    0.468701] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator
[    0.468872] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator
[    0.469301] exynos5_usb3drd_phy 12500000.phy: supply vbus not found, using dummy regulator
[    0.469472] exynos5_usb3drd_phy 12500000.phy: supply vbus-boost not found, using dummy regulator
[    0.477328] dma-pl330 3880000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.477365] dma-pl330 3880000.dma-controller: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.480631] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.480666] dma-pl330 121a0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.483839] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.483875] dma-pl330 121b0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.485088] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.485121] dma-pl330 10800000.dma-controller: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.502474] dma-pl330 3880000.dma-controller: PM domain MAU will not be powered off
[    0.579116] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.581840] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 124, base_baud = 0) is a S3C6400/10
[    0.582398] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 125, base_baud = 0) is a S3C6400/10
[    1.598204] printk: console [ttySAC2] enabled
[    1.604993] exynos-trng 10830600.rng: Exynos True Random Number Generator.
[    1.612157] exynos-mixer 14450000.mixer: Adding to iommu group 0
[    1.619675] exynos-drm-g2d 10850000.g2d: Adding to iommu group 1
[    1.626137] exynos-rotator 11c00000.rotator: Adding to iommu group 2
[    1.632402] exynos-scaler 12800000.scaler: Adding to iommu group 3
[    1.638899] exynos-scaler 12810000.scaler: Adding to iommu group 4
[    1.645347] exynos-scaler 12820000.scaler: Adding to iommu group 5
[    1.652080] exynos-drm-gsc 13e00000.video-scaler: Adding to iommu group 6
[    1.658212] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered successfully.
[    1.665439] exynos-drm-gsc 13e10000.video-scaler: Adding to iommu group 7
[    1.672553] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered successfully.
[    1.697227] brd: module loaded
[    1.700035] usbcore: registered new interface driver r8152
[    1.704367] usbcore: registered new interface driver cdc_ether
[    1.710121] usbcore: registered new interface driver cdc_subset
[    1.716089] usbcore: registered new interface driver r8153_ecm
[    1.724797] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.730291] exynos-ehci 12110000.usb: EHCI Host Controller
[    1.735799] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    1.744091] exynos-ehci 12110000.usb: irq 133, io mem 0x12110000
[    1.770627] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    1.775395] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.783452] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.790635] usb usb1: Product: EHCI Host Controller
[    1.795449] usb usb1: Manufacturer: Linux 6.1.45-7 ehci_hcd
[    1.801023] usb usb1: SerialNumber: 12110000.usb
[    1.806390] hub 1-0:1.0: USB hub found
[    1.809354] hub 1-0:1.0: 3 ports detected
[    1.814768] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.820265] exynos-ohci 12120000.usb: USB Host Controller
[    1.825707] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    1.833614] exynos-ohci 12120000.usb: irq 133, io mem 0x12120000
[    1.904867] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    1.911722] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.918866] usb usb2: Product: USB Host Controller
[    1.923656] usb usb2: Manufacturer: Linux 6.1.45-7 ohci_hcd
[    1.929175] usb usb2: SerialNumber: 12120000.usb
[    1.934488] hub 2-0:1.0: USB hub found
[    1.937531] hub 2-0:1.0: 3 ports detected
[    1.944120] mousedev: PS/2 mouse device common for all mice
[    1.949957] i2c_dev: i2c /dev entries driver
[    1.978603] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    1.995602] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[    2.015400] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.084634] s5m-rtc s2mps14-rtc: registered as rtc0
[    2.089898] s5m-rtc s2mps14-rtc: setting system clock to 2000-01-01T00:18:56 UTC (946685936)
[    2.097270] s2mps11-clk s2mps11-clk: DMA mask not set
[    2.111122] exynos-tmu 10060000.tmu: More trip points than supported by this TMU.
[    2.117145] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode.
[    2.126365] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.127081] exynos-tmu 10064000.tmu: More trip points than supported by this TMU.
[    2.133622] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.141065] exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode.
[    2.155824] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.164159] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.165312] exynos-tmu 10068000.tmu: More trip points than supported by this TMU.
[    2.178165] exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode.
[    2.188157] exynos-tmu 1006c000.tmu: More trip points than supported by this TMU.
[    2.194219] exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode.
[    2.204115] exynos-tmu 100a0000.tmu: More trip points than supported by this TMU.
[    2.210132] exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode.
[    2.219504] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    2.227234] device-mapper: uevent: version 1.0.3
[    2.231451] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    2.251337] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.258313] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.265008] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.273343] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.282983] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.289959] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.296653] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.305113] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.312772] sdhci: Secure Digital Host Controller Interface driver
[    2.317701] sdhci: Copyright(c) Pierre Ossman
[    2.322351] Synopsys Designware Multimedia Card Interface Driver
[    2.329036] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    2.329051] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    2.341853] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    2.342937] s5p-secss 10830000.sss: s5p-sss driver registered
[    2.348137] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    2.348368] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    2.348387] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    2.348672] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 145,64 bit host data width,64 deep fifo
[    2.350654] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    2.357088] hid: raw HID events driver (C) Jiri Kosina
[    2.359407] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 144,64 bit host data width,64 deep fifo
[    2.372232] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.401176] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.426371] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    2.431749] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    2.438282] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    2.444916] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    2.451914] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0-0)
[    2.459382] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0-1)
[    2.467342] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1-0)
[    2.475207] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1-1)
[    2.486756] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_0 not found
[    2.491120] mmc_host mmc1: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
[    2.493251] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_1 not found
[    2.511359] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0
[    2.519593] exynos-adc 12d10000.adc: error -ENXIO: IRQ index 1 not found
[    2.530486] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s
[    2.538458] NET: Registered PF_PACKET protocol family
[    2.542067] NET: Registered PF_KEY protocol family
[    2.547287] Key type dns_resolver registered
[    2.550757] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.551800] Registering SWP/SWPB emulation handler
[    2.559438] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.565665] registered taskstats version 1
[    2.570906] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.574978] Loading compiled-in X.509 certificates
[    2.583294] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.589202] Key type .fscrypt registered
[    2.598589] Key type fscrypt-provisioning registered
[    2.612660] mmc1: new ultra high speed SDR104 SDXC card at address 0001
[    2.619090] mmcblk1: mmc1:0001 SD64G 58.2 GiB 
[    2.625746]  mmcblk1: p1 p2
[    2.730780] usb 2-1: new full-speed USB device number 2 using exynos-ohci
[    2.830685] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.837666] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.850670] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.857638] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    3.006861] usb 2-1: New USB device found, idVendor=046a, idProduct=010e, bcdDevice= 0.13
[    3.013926] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    3.021013] usb 2-1: Product: USB Wireless Device
[    3.100660] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    3.107647] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    3.130938] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    3.137908] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    3.220803] Freeing initrd memory: 8252K
[    3.223868] reboot: Failed to start orderly shutdown: forcing the issue
[    3.230442] Emergency Sync complete
[    3.239143] Key type encrypted registered
[    3.334385] reboot[00][00]

User avatar
odroid
Site Admin
Posts: 42177
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English, Korean
ODROIDs: ODROID
Has thanked: 3609 times
Been thanked: 2004 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by odroid »

@matty67,
Did you flash this OS image?

@mdrjr,
Can you find a link of workaround patch in our Github kernel 6.1 & 6.6 branches for partial broken temperature sensors?
These users thanked the author odroid for the post:
matty67 (Wed Feb 07, 2024 3:22 am)

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Yes. I´ve flashed it. Filename is ubuntu-22.04-6.1-minimal-odroid-xu4-20230905.img.xz (from this location https://de.eu.odroid.in/ubuntu_22.04lts ... 905.img.xz )

I´ve tested, to install the kernel on a 5.4 running minimal system but it´s not working too.

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

6.1 already has the patch. (https://github.com/hardkernel/linux/com ... d6c77cb504)
6.6 will have from today. (https://github.com/hardkernel/linux/com ... e97945d82b)

He's issue is that the image he flashed has a older kernel, looking at the date I merged the change and the date the kernel was build
I can confirm that it doesn't have the patch yet.

So, in this case, flash a image with kernel 5.4 and update to kernel 6.1 with the instructions from the wiki:
https://wiki.odroid.com/odroid-xu4/os_i ... l_54_to_61
These users thanked the author mdrjr for the post:
odroid (Wed Feb 07, 2024 9:46 am)

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Hi @mdrjr
I´ve done the update steps from a 5.4 kernel but the problem still exists.

Code: Select all

[00]

U-Boot 2017.05-00008-g6a9ddb8303-dirty (May 19 2020 - 19:48:01 +0900) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz
Model: Odroid XU4 based on EXYNOS5422
Board: Odroid XU4 based on EXYNOS5422
Type:  xu4
DRAM:  2 GiB
MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
MMC Device 0 ( SD ): 58.2 GiB
mmc_init: -5, time 4
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Press quickly 'Enter' twice to stop autoboot:  0 
reading /boot.ini
2365 bytes read in 4 ms (577.1 KiB/s)
## Executing script at 43e00000
reading config.ini
6911 bytes read in 6 ms (1.1 MiB/s)
ini: Imported macaddr as 00:1e:06:61:7a:39
ini: Imported vout as hdmi
ini: Imported HPD as true
ini: Imported cecenable as false
ini: Imported disable_vu7 as false
ini: Imported ddr_freq as 825
ini: Imported overlay_resize as 16384
ini: Imported overlay_profile as 
ini: Imported overlays as spi0 i2c0 i2c1 uart0
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
reading zImage
7135928 bytes read in 482 ms (14.1 MiB/s)
reading uInitrd
8838868 bytes read in 592 ms (14.2 MiB/s)
reading exynos5422-odroidxu4.dtb
88559 bytes read in 13 ms (6.5 MiB/s)
reading overlays/spi0.dtbo
691 bytes read in 6 ms (112.3 KiB/s)
reading overlays/i2c0.dtbo
224 bytes read in 6 ms (36.1 KiB/s)
reading overlays/i2c1.dtbo
226 bytes read in 6 ms (36.1 KiB/s)
reading overlays/uart0.dtbo
227 bytes read in 6 ms (36.1 KiB/s)
Kernel image @ 0x40008000 [ 0x000000 - 0x6ce2b8 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8838804 Bytes = 8.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 44000000
   Booting using the fdt blob at 0x44000000
   reserving fdt memory region: addr=44000000 size=2c000
   Using Device Tree in place at 44000000, end 4402efff

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 6.1.75-19 (root@builder32) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #1 SMP PREEMPT Mon Jan 29 22:34:56 UTC 2024
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel ODROID XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0x00000000b6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000040000000-0x000000006fffffff]
[    0.000000]   HighMem  [mem 0x0000000070000000-0x00000000be9fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Running under secure firmware.
[    0.000000] percpu: Embedded 17 pages/cpu s39124 r8192 d22316 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false
[    0.000000] hdmi: using HDMI mode
[    0.000000] Unknown kernel command line parameters "false HPD=true vout=hdmi", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1895044K/2074624K available (12288K kernel code, 1125K rwdata, 2880K rodata, 2048K init, 365K bss, 48508K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000031] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57
[    0.001526] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.001550] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.001571] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001588] Ignoring duplicate/late registration of read_current_timer delay
[    0.002381] Console: colour dummy device 80x30
[    0.003138] printk: console [tty1] enabled
[    0.003206] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003256] CPU: Testing write buffer coherency: ok
[    0.003347] pid_max: default: 32768 minimum: 301
[    0.003497] LSM: Security Framework initializing
[    0.003689] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003743] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005489] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.006921] cblist_init_generic: Setting adjustable number of callback queues.
[    0.006970] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007158] cblist_init_generic: Setting adjustable number of callback queues.
[    0.007194] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007405] Setting up static identity map for 0x40200000 - 0x40200060
[    0.007752] ARM CCI driver probed
[    0.008345] Exynos MCPM support installed
[    0.008748] rcu: Hierarchical SRCU implementation.
[    0.008774] rcu: 	Max phase no-delay instances is 1000.
[    0.010061] smp: Bringing up secondary CPUs ...
[    0.011220] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.012525] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.013756] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.014950] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.014968] CPU4: detected I-Cache line size mismatch, workaround enabled
[    0.014976] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.015069] CPU4: Spectre BHB: enabling loop workaround for all CPUs
[    0.016330] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.016344] CPU5: detected I-Cache line size mismatch, workaround enabled
[    0.016352] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.017668] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.017683] CPU6: detected I-Cache line size mismatch, workaround enabled
[    0.017691] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.018964] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.018979] CPU7: detected I-Cache line size mismatch, workaround enabled
[    0.018987] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.019224] smp: Brought up 1 node, 8 CPUs
[    0.019287] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.019316] CPU: All CPU(s) started in HYP mode.
[    0.019338] CPU: Virtualization extensions available.
[    0.020812] devtmpfs: initialized
[    0.041603] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.041883] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.041925] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.045123] pinctrl core: initialized pinctrl subsystem
[    0.048004] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.051697] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.053399] audit: initializing netlink subsys (disabled)
[    0.053680] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1
[    0.054250] thermal_sys: Registered thermal governor 'step_wise'
[    0.054521] cpuidle: using governor menu
[    0.054999] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.055029] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.184628] EXYNOS5420 PMU initialized
[    0.421797] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.424370] fbcon: Taking over console
[    0.426140] iommu: Default domain type: Translated 
[    0.426179] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.426702] usbcore: registered new interface driver usbfs
[    0.426788] usbcore: registered new interface driver hub
[    0.426871] usbcore: registered new device driver usb
[    0.427717] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.427761] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.428206] s3c-i2c 12c70000.i2c: i2c-0: S3C I2C adapter
[    0.428487] s3c-i2c 12c80000.i2c: slave address 0x00
[    0.428524] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[    0.428892] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[    0.429492] mc: Linux media interface: v0.10
[    0.429600] videodev: Linux video capture interface: v2.00
[    0.430417] Advanced Linux Sound Architecture Driver Initialized.
[    0.431798] clocksource: Switched to clocksource mct-frc
[    0.432396] VFS: Disk quotas dquot_6.6.0
[    0.432506] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.447447] NET: Registered PF_INET protocol family
[    0.447986] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.451532] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.451688] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.451742] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.451920] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.452199] TCP: Hash tables configured (established 8192 bind 8192)
[    0.452487] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.452574] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.452954] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.453043] NET: Registered PF_XDP protocol family
[    0.453823] Trying to unpack rootfs image as initramfs...
[    0.462305] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.463482] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.465581] Initialise system trusted keyrings
[    0.465895] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.475434] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.565586] NET: Registered PF_ALG protocol family
[    0.565626] Key type asymmetric registered
[    0.565648] Asymmetric key parser 'x509' registered
[    0.565888] bounce: pool size: 64 pages
[    0.566045] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.566392] io scheduler mq-deadline registered
[    0.566422] io scheduler kyber registered
[    0.566679] io scheduler bfq registered
[    0.568445] samsung-pinctrl 13400000.pinctrl: Failed to create device link (0x180) with soc
[    0.570782] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator
[    0.571877] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator
[    0.572060] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator
[    0.572479] exynos5_usb3drd_phy 12500000.phy: supply vbus not found, using dummy regulator
[    0.572655] exynos5_usb3drd_phy 12500000.phy: supply vbus-boost not found, using dummy regulator
[    0.580943] dma-pl330 3880000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.580978] dma-pl330 3880000.dma-controller: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.584192] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.584226] dma-pl330 121a0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.587295] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.587327] dma-pl330 121b0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.588546] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.588578] dma-pl330 10800000.dma-controller: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.606076] dma-pl330 3880000.dma-controller: PM domain MAU will not be powered off
[    0.679333] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.682041] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 124, base_baud = 0) is a S3C6400/10
[    0.682609] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 125, base_baud = 0) is a S3C6400/10
[    1.706737] printk: console [ttySAC2] enabled
[    1.713495] exynos-trng 10830600.rng: Exynos True Random Number Generator.
[    1.720636] exynos-mixer 14450000.mixer: Adding to iommu group 0
[    1.728174] exynos-drm-g2d 10850000.g2d: Adding to iommu group 1
[    1.734706] exynos-rotator 11c00000.rotator: Adding to iommu group 2
[    1.740850] exynos-scaler 12800000.scaler: Adding to iommu group 3
[    1.747461] exynos-scaler 12810000.scaler: Adding to iommu group 4
[    1.753860] exynos-scaler 12820000.scaler: Adding to iommu group 5
[    1.760504] exynos-drm-gsc 13e00000.video-scaler: Adding to iommu group 6
[    1.766646] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered successfully.
[    1.773842] exynos-drm-gsc 13e10000.video-scaler: Adding to iommu group 7
[    1.780904] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered successfully.
[    1.805080] brd: module loaded
[    1.807877] usbcore: registered new device driver r8152-cfgselector
[    1.812992] usbcore: registered new interface driver r8152
[    1.818414] usbcore: registered new interface driver cdc_ether
[    1.824249] usbcore: registered new interface driver cdc_subset
[    1.830123] usbcore: registered new interface driver r8153_ecm
[    1.838888] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.844418] exynos-ehci 12110000.usb: EHCI Host Controller
[    1.849859] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    1.858133] exynos-ehci 12110000.usb: irq 133, io mem 0x12110000
[    1.891856] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    1.896629] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.904679] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.911866] usb usb1: Product: EHCI Host Controller
[    1.916677] usb usb1: Manufacturer: Linux 6.1.75-19 ehci_hcd
[    1.922341] usb usb1: SerialNumber: 12110000.usb
[    1.927642] hub 1-0:1.0: USB hub found
[    1.930665] hub 1-0:1.0: 3 ports detected
[    1.936072] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.941572] exynos-ohci 12120000.usb: USB Host Controller
[    1.946991] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    1.954899] exynos-ohci 12120000.usb: irq 133, io mem 0x12120000
[    2.026101] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    2.032947] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    2.040093] usb usb2: Product: USB Host Controller
[    2.044892] usb usb2: Manufacturer: Linux 6.1.75-19 ohci_hcd
[    2.050488] usb usb2: SerialNumber: 12120000.usb
[    2.055808] hub 2-0:1.0: USB hub found
[    2.058844] hub 2-0:1.0: 3 ports detected
[    2.065403] mousedev: PS/2 mouse device common for all mice
[    2.071247] i2c_dev: i2c /dev entries driver
[    2.098506] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    2.115074] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[    2.134505] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.204277] s5m-rtc s2mps14-rtc: registered as rtc0
[    2.209539] s5m-rtc s2mps14-rtc: setting system clock to 2024-02-07T06:26:06 UTC (1707287166)
[    2.216983] s2mps11-clk s2mps11-clk: DMA mask not set
[    2.231915] exynos-tmu 10060000.tmu: More trip points than supported by this TMU.
[    2.237940] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode.
[    2.247158] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.247884] exynos-tmu 10064000.tmu: More trip points than supported by this TMU.
[    2.254449] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.261862] exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode.
[    2.270975] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.285076] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.291538] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.292753] exynos-tmu 10068000.tmu: More trip points than supported by this TMU.
[    2.299900] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.307357] exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode.
[    2.324011] exynos-tmu 1006c000.tmu: More trip points than supported by this TMU.
[    2.330034] exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode.
[    2.339983] exynos-tmu 100a0000.tmu: More trip points than supported by this TMU.
[    2.346043] exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode.
[    2.355365] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    2.363122] device-mapper: uevent: version 1.0.3
[    2.367262] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    2.387142] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.394151] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.400771] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.409142] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.418449] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.425457] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.432128] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.440457] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.448225] sdhci: Secure Digital Host Controller Interface driver
[    2.453187] sdhci: Copyright(c) Pierre Ossman
[    2.457797] Synopsys Designware Multimedia Card Interface Driver
[    2.464601] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    2.464613] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    2.477328] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    2.483614] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    2.483795] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    2.484361] s5p-secss 10830000.sss: s5p-sss driver registered
[    2.486374] hid: raw HID events driver (C) Jiri Kosina
[    2.489323] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 144,64 bit host data width,64 deep fifo
[    2.495377] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    2.520961] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 145,64 bit host data width,64 deep fifo
[    2.522348] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.533576] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    2.551721] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    2.557109] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    2.562724] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.564695] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    2.579722] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    2.586796] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0-0)
[    2.594218] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0-1)
[    2.602243] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1-0)
[    2.609948] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1-1)
[    2.615027] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
[    2.629298] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_0 not found
[    2.635784] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_1 not found
[    2.643887] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0
[    2.657157] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s
[    2.665277] NET: Registered PF_PACKET protocol family
[    2.668870] NET: Registered PF_KEY protocol family
[    2.674151] Key type dns_resolver registered
[    2.678429] Registering SWP/SWPB emulation handler
[    2.683106] registered taskstats version 1
[    2.686729] Loading compiled-in X.509 certificates
[    2.692138] Key type .fscrypt registered
[    2.695372] Key type fscrypt-provisioning registered
[    2.701859] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.708824] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.715474] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.723838] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.733863] mmc0: new ultra high speed SDR104 SDXC card at address 0001
[    2.740324] mmcblk0: mmc0:0001 SD64G 58.2 GiB 
[    2.747411]  mmcblk0: p1 p2
[    2.871956] usb 2-1: new full-speed USB device number 2 using exynos-ohci
[    2.971915] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    2.978922] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    2.985575] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    2.993930] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    3.148141] usb 2-1: New USB device found, idVendor=046a, idProduct=010e, bcdDevice= 0.13
[    3.155227] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    3.162290] usb 2-1: Product: USB Wireless Device
[    3.241910] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[    3.248903] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    3.255584] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[    3.263919] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[    3.450655] Freeing initrd memory: 8632K
[    3.453778] reboot: Failed to start orderly shutdown: forcing the issue
[    3.460286] Emergency Sync complete
[    3.468868] Key type encrypted registered
[    3.490907] reboot:[00][00]

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

Ok, can you do a test for me?

replace the zImage on the microsd with this?
http://deb.odroid.in/zImage

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Ok. Here is the output from the boot process with your zImage.

Code: Select all

[00]

U-Boot 2017.05-00008-g6a9ddb8303-dirty (May 19 2020 - 19:48:01 +0900) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz
Model: Odroid XU4 based on EXYNOS5422
Board: Odroid XU4 based on EXYNOS5422
Type:  xu4
DRAM:  2 GiB
MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
MMC Device 0 ( SD ): 58.2 GiB
mmc_init: -5, time 4
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Press quickly 'Enter' twice to stop autoboot:  0 
reading /boot.ini
2365 bytes read in 4 ms (577.1 KiB/s)
## Executing script at 43e00000
reading config.ini
6911 bytes read in 6 ms (1.1 MiB/s)
ini: Imported macaddr as 00:1e:06:61:7a:39
ini: Imported vout as hdmi
ini: Imported HPD as true
ini: Imported cecenable as false
ini: Imported disable_vu7 as false
ini: Imported ddr_freq as 825
ini: Imported overlay_resize as 16384
ini: Imported overlay_profile as 
ini: Imported overlays as spi0 i2c0 i2c1 uart0
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
reading zImage
7142008 bytes read in 480 ms (14.2 MiB/s)
reading uInitrd
8838868 bytes read in 591 ms (14.3 MiB/s)
reading exynos5422-odroidxu4.dtb
88559 bytes read in 12 ms (7 MiB/s)
reading overlays/spi0.dtbo
691 bytes read in 6 ms (112.3 KiB/s)
reading overlays/i2c0.dtbo
224 bytes read in 5 ms (43 KiB/s)
reading overlays/i2c1.dtbo
226 bytes read in 6 ms (36.1 KiB/s)
reading overlays/uart0.dtbo
227 bytes read in 6 ms (36.1 KiB/s)
Kernel image @ 0x40008000 [ 0x000000 - 0x6cfa78 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8838804 Bytes = 8.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 44000000
   Booting using the fdt blob at 0x44000000
   reserving fdt memory region: addr=44000000 size=2c000
   Using Device Tree in place at 44000000, end 4402efff

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 6.1.75+ (mdrjr@powah) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #14 SMP PREEMPT Wed Feb  7 13:26:06 -03 2024
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel ODROID XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0x00000000b6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000040000000-0x000000006fffffff]
[    0.000000]   HighMem  [mem 0x0000000070000000-0x00000000be9fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Running under secure firmware.
[    0.000000] percpu: Embedded 17 pages/cpu s39124 r8192 d22316 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false
[    0.000000] hdmi: using HDMI mode
[    0.000000] Unknown kernel command line parameters "false HPD=true vout=hdmi", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1895044K/2074624K available (12288K kernel code, 1125K rwdata, 2884K rodata, 2048K init, 365K bss, 48508K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000032] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57
[    0.001526] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.001551] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.001573] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001589] Ignoring duplicate/late registration of read_current_timer delay
[    0.002382] Console: colour dummy device 80x30
[    0.003133] printk: console [tty1] enabled
[    0.003200] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003248] CPU: Testing write buffer coherency: ok
[    0.003338] pid_max: default: 32768 minimum: 301
[    0.003489] LSM: Security Framework initializing
[    0.003683] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003738] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005481] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.006892] cblist_init_generic: Setting adjustable number of callback queues.
[    0.006939] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007129] cblist_init_generic: Setting adjustable number of callback queues.
[    0.007165] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007372] Setting up static identity map for 0x40200000 - 0x40200060
[    0.007726] ARM CCI driver probed
[    0.008322] Exynos MCPM support installed
[    0.008723] rcu: Hierarchical SRCU implementation.
[    0.008750] rcu: 	Max phase no-delay instances is 1000.
[    0.010031] smp: Bringing up secondary CPUs ...
[    0.011180] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.012474] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.013704] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.014904] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.014921] CPU4: detected I-Cache line size mismatch, workaround enabled
[    0.014929] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.015019] CPU4: Spectre BHB: enabling loop workaround for all CPUs
[    0.016283] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.016297] CPU5: detected I-Cache line size mismatch, workaround enabled
[    0.016304] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.017612] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.017626] CPU6: detected I-Cache line size mismatch, workaround enabled
[    0.017633] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.018906] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.018920] CPU7: detected I-Cache line size mismatch, workaround enabled
[    0.018928] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.019163] smp: Brought up 1 node, 8 CPUs
[    0.019227] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.019256] CPU: All CPU(s) started in HYP mode.
[    0.019277] CPU: Virtualization extensions available.
[    0.020733] devtmpfs: initialized
[    0.042062] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.042344] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.042385] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.045554] pinctrl core: initialized pinctrl subsystem
[    0.048454] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.052147] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.053915] audit: initializing netlink subsys (disabled)
[    0.054196] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1
[    0.054779] thermal_sys: Registered thermal governor 'step_wise'
[    0.055052] cpuidle: using governor menu
[    0.055522] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.055551] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.185930] EXYNOS5420 PMU initialized
[    0.303841] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.305771] fbcon: Taking over console
[    0.307544] iommu: Default domain type: Translated 
[    0.307567] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.307969] usbcore: registered new interface driver usbfs
[    0.308037] usbcore: registered new interface driver hub
[    0.308107] usbcore: registered new device driver usb
[    0.308833] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.308863] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.309226] s3c-i2c 12c70000.i2c: i2c-0: S3C I2C adapter
[    0.309438] s3c-i2c 12c80000.i2c: slave address 0x00
[    0.309466] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[    0.309764] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[    0.310252] mc: Linux media interface: v0.10
[    0.310333] videodev: Linux video capture interface: v2.00
[    0.310946] Advanced Linux Sound Architecture Driver Initialized.
[    0.311985] clocksource: Switched to clocksource mct-frc
[    0.312466] VFS: Disk quotas dquot_6.6.0
[    0.312544] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.326865] NET: Registered PF_INET protocol family
[    0.327127] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.328992] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.329043] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.329077] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.329230] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.329535] TCP: Hash tables configured (established 8192 bind 8192)
[    0.329656] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.329716] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.329969] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.330031] NET: Registered PF_XDP protocol family
[    0.330618] Trying to unpack rootfs image as initramfs...
[    0.342294] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.343505] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.345636] Initialise system trusted keyrings
[    0.345984] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.355491] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.442980] NET: Registered PF_ALG protocol family
[    0.443017] Key type asymmetric registered
[    0.443038] Asymmetric key parser 'x509' registered
[    0.443278] bounce: pool size: 64 pages
[    0.443428] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.443826] io scheduler mq-deadline registered
[    0.443855] io scheduler kyber registered
[    0.444115] io scheduler bfq registered
[    0.445791] samsung-pinctrl 13400000.pinctrl: Failed to create device link (0x180) with soc
[    0.448140] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator
[    0.449141] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator
[    0.449313] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator
[    0.449739] exynos5_usb3drd_phy 12500000.phy: supply vbus not found, using dummy regulator
[    0.449913] exynos5_usb3drd_phy 12500000.phy: supply vbus-boost not found, using dummy regulator
[    0.458315] dma-pl330 3880000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.458352] dma-pl330 3880000.dma-controller: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.461548] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.461581] dma-pl330 121a0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.464803] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.464836] dma-pl330 121b0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.466100] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.466131] dma-pl330 10800000.dma-controller: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.483454] dma-pl330 3880000.dma-controller: PM domain MAU will not be powered off
[    0.553395] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.556079] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 124, base_baud = 0) is a S3C6400/10
[    0.556639] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 125, base_baud = 0) is a S3C6400/10
[    1.580409] printk: console [ttySAC2] enabled
[    1.587229] exynos-trng 10830600.rng: Exynos True Random Number Generator.
[    1.594396] exynos-mixer 14450000.mixer: Adding to iommu group 0
[    1.601921] exynos-drm-g2d 10850000.g2d: Adding to iommu group 1
[    1.608356] exynos-rotator 11c00000.rotator: Adding to iommu group 2
[    1.614544] exynos-scaler 12800000.scaler: Adding to iommu group 3
[    1.621151] exynos-scaler 12810000.scaler: Adding to iommu group 4
[    1.627676] exynos-scaler 12820000.scaler: Adding to iommu group 5
[    1.634402] exynos-drm-gsc 13e00000.video-scaler: Adding to iommu group 6
[    1.640581] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered successfully.
[    1.647745] exynos-drm-gsc 13e10000.video-scaler: Adding to iommu group 7
[    1.654877] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered successfully.
[    1.679329] brd: module loaded
[    1.682178] usbcore: registered new device driver r8152-cfgselector
[    1.687215] usbcore: registered new interface driver r8152
[    1.692701] usbcore: registered new interface driver ax88179_178a
[    1.698725] usbcore: registered new interface driver cdc_ether
[    1.704559] usbcore: registered new interface driver cdc_subset
[    1.710447] usbcore: registered new interface driver r8153_ecm
[    1.719222] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.724757] exynos-ehci 12110000.usb: EHCI Host Controller
[    1.730197] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    1.738517] exynos-ehci 12110000.usb: irq 133, io mem 0x12110000
[    1.772044] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    1.776812] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.784869] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.792057] usb usb1: Product: EHCI Host Controller
[    1.796866] usb usb1: Manufacturer: Linux 6.1.75+ ehci_hcd
[    1.802355] usb usb1: SerialNumber: 12110000.usb
[    1.807685] hub 1-0:1.0: USB hub found
[    1.810679] hub 1-0:1.0: 3 ports detected
[    1.816122] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.821623] exynos-ohci 12120000.usb: USB Host Controller
[    1.827059] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    1.834889] exynos-ohci 12120000.usb: irq 133, io mem 0x12120000
[    1.906302] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    1.913165] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.920300] usb usb2: Product: USB Host Controller
[    1.925092] usb usb2: Manufacturer: Linux 6.1.75+ ohci_hcd
[    1.930521] usb usb2: SerialNumber: 12120000.usb
[    1.935849] hub 2-0:1.0: USB hub found
[    1.938877] hub 2-0:1.0: 3 ports detected
[    1.945499] mousedev: PS/2 mouse device common for all mice
[    1.951373] i2c_dev: i2c /dev entries driver
[    1.979235] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    1.996581] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[    2.016333] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.086737] s5m-rtc s2mps14-rtc: registered as rtc0
[    2.092062] s5m-rtc s2mps14-rtc: setting system clock to 2024-02-07T17:28:36 UTC (1707326916)
[    2.099469] s2mps11-clk s2mps11-clk: DMA mask not set
[    2.114528] exynos-tmu 10060000.tmu: More trip points than supported by this TMU.
[    2.120555] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode.
[    2.130494] exynos-tmu 10064000.tmu: More trip points than supported by this TMU.
[    2.136552] exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode.
[    2.146467] exynos-tmu 10068000.tmu: More trip points than supported by this TMU.
[    2.152520] exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode.
[    2.162491] exynos-tmu 1006c000.tmu: More trip points than supported by this TMU.
[    2.168516] exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode.
[    2.178461] exynos-tmu 100a0000.tmu: More trip points than supported by this TMU.
[    2.184525] exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode.
[    2.193836] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    2.201544] device-mapper: uevent: version 1.0.3
[    2.205802] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    2.229291] sdhci: Secure Digital Host Controller Interface driver
[    2.234208] sdhci: Copyright(c) Pierre Ossman
[    2.238825] Synopsys Designware Multimedia Card Interface Driver
[    2.245974] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    2.246183] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    2.258470] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    2.258473] s5p-secss 10830000.sss: s5p-sss driver registered
[    2.260860] hid: raw HID events driver (C) Jiri Kosina
[    2.264695] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    2.264980] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    2.265015] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    2.265351] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 145,64 bit host data width,64 deep fifo
[    2.267310] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    2.287653] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.293050] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 144,64 bit host data width,64 deep fifo
[    2.332683] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    2.337976] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    2.341698] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.345426] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    2.360654] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    2.367692] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0-0)
[    2.375174] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0-1)
[    2.383052] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1-0)
[    2.390903] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1-1)
[    2.402694] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_0 not found
[    2.409139] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_1 not found
[    2.417383] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0
[    2.425245] mmc_host mmc1: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
[    2.438202] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s
[    2.446147] NET: Registered PF_PACKET protocol family
[    2.449731] NET: Registered PF_KEY protocol family
[    2.455186] Key type dns_resolver registered
[    2.459286] Registering SWP/SWPB emulation handler
[    2.464107] registered taskstats version 1
[    2.467591] Loading compiled-in X.509 certificates
[    2.472892] Key type .fscrypt registered
[    2.476238] Key type fscrypt-provisioning registered
[    2.544270] mmc1: new ultra high speed SDR104 SDXC card at address 0001
[    2.551339] mmcblk1: mmc1:0001 SD64G 58.2 GiB 
[    2.559486]  mmcblk1: p1 p2
[    2.712191] usb 2-1: new full-speed USB device number 2 using exynos-ohci
[    2.988348] usb 2-1: New USB device found, idVendor=046a, idProduct=010e, bcdDevice= 0.13
[    2.995257] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    3.002300] usb 2-1: Product: USB Wireless Device
[    3.099705] Freeing initrd memory: 8632K
[    3.143992] Key type encrypted registered
[    3.225294] exynos-chipid 10000000.chipid: cpu0 opp0, freq: 1500 missing
[    3.230571] exynos-chipid 10000000.chipid: cpu4 opp0, freq: 2100 missing
[    3.237287] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5800] PRO_ID[0xe5422000] REV[0x1] Detected
[    3.249181] OF: graph: no port node found in /soc/hdmi@14530000
[    3.255481] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[    3.261839] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0e7bc8c)
[    3.268520] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc0e7c26c)
[    3.275220] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully registered.
[    3.283285] exynos-drm exynos-drm: bound 10850000.g2d (ops 0xc0e7d27c)
[    3.289777] exynos-rotator 11c00000.rotator: The exynos rotator has been probed successfully
[    3.298193] exynos-drm exynos-drm: bound 11c00000.rotator (ops 0xc0e7db08)
[    3.305070] exynos-scaler 12800000.scaler: The exynos scaler has been probed successfully
[    3.313912] exynos-drm exynos-drm: bound 12800000.scaler (ops 0xc0e7e250)
[    3.319956] exynos-scaler 12810000.scaler: The exynos scaler has been probed successfully
[    3.328123] exynos-drm exynos-drm: bound 12810000.scaler (ops 0xc0e7e250)
[    3.334891] exynos-scaler 12820000.scaler: The exynos scaler has been probed successfully
[    3.343012] exynos-drm exynos-drm: bound 12820000.scaler (ops 0xc0e7e250)
[    3.349770] exynos-drm-gsc 13e00000.video-scaler: The exynos gscaler has been probed successfully
[    3.358624] exynos-drm exynos-drm: bound 13e00000.video-scaler (ops 0xc0e7eb24)
[    3.365921] exynos-drm-gsc 13e10000.video-scaler: The exynos gscaler has been probed successfully
[    3.374740] exynos-drm exynos-drm: bound 13e10000.video-scaler (ops 0xc0e7eb24)
[    3.543935] Console: switching to colour frame buffer device 240x75
[    3.600961] exynos-drm exynos-drm: [drm] fb0: exynosdrmfb frame buffer device
[    3.609340] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 0
[    3.620750] mali 11800000.gpu: GPU identified as 0x0620 r0p1 status 0
[    3.626020] mali 11800000.gpu: Protected mode not available
[    3.633403] mali 11800000.gpu: Probed as mali0
[    3.642650] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.646792] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[    3.655408] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.663977] xhci-hcd xhci-hcd.8.auto: irq 153, io mem 0x12000000
[    3.670124] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.675237] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[    3.682790] xhci-hcd xhci-hcd.8.auto: Host supports USB 3.0 SuperSpeed
[    3.689370] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.697529] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.704698] usb usb3: Product: xHCI Host Controller
[    3.709514] usb usb3: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.714998] usb usb3: SerialNumber: xhci-hcd.8.auto
[    3.720226] hub 3-0:1.0: USB hub found
[    3.723591] hub 3-0:1.0: 1 port detected
[    3.727731] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.735635] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.743781] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.750947] usb usb4: Product: xHCI Host Controller
[    3.755865] usb usb4: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.761251] usb usb4: SerialNumber: xhci-hcd.8.auto
[    3.766523] hub 4-0:1.0: USB hub found
[    3.769839] hub 4-0:1.0: 1 port detected
[    3.776570] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.780612] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    3.788939] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.797727] xhci-hcd xhci-hcd.9.auto: irq 154, io mem 0x12400000
[    3.803827] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.809058] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 6
[    3.816707] xhci-hcd xhci-hcd.9.auto: Host supports USB 3.0 SuperSpeed
[    3.823337] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.831419] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.838634] usb usb5: Product: xHCI Host Controller
[    3.843462] usb usb5: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.848911] usb usb5: SerialNumber: xhci-hcd.9.auto
[    3.854201] hub 5-0:1.0: USB hub found
[    3.857478] hub 5-0:1.0: 1 port detected
[    3.861655] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.869609] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.877699] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.884954] usb usb6: Product: xHCI Host Controller
[    3.891804] usb usb6: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.897918] usb usb6: SerialNumber: xhci-hcd.9.auto
[    3.903809] hub 6-0:1.0: USB hub found
[    3.908168] hub 6-0:1.0: 1 port detected
[    3.913960] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[    3.920342] s3c-rtc 101e0000.rtc: registered as rtc1
[    3.927859] exynos-bus: new bus device registered: soc:bus-wcore ( 88700 KHz ~ 532000 KHz)
[    3.937474] exynos-bus: new bus device registered: soc:bus-noc ( 66600 KHz ~ 111000 KHz)
[    3.946863] exynos-bus: new bus device registered: soc:bus-fsys-apb (111000 KHz ~ 222000 KHz)
[    3.956649] exynos-bus: new bus device registered: soc:bus-fsys2 ( 75000 KHz ~ 200000 KHz)
[    3.966312] exynos-bus: new bus device registered: soc:bus-mfc ( 83250 KHz ~ 333000 KHz)
[    3.975718] exynos-bus: new bus device registered: soc:bus-gen ( 88700 KHz ~ 266000 KHz)
[    3.984790] exynos-bus: new bus device registered: soc:bus-peri ( 66600 KHz ~  66600 KHz)
[    3.994391] exynos-bus: new bus device registered: soc:bus-g2d ( 83250 KHz ~ 333000 KHz)
[    4.003753] exynos-bus: new bus device registered: soc:bus-g2d-acp ( 66500 KHz ~ 266000 KHz)
[    4.013475] exynos-bus: new bus device registered: soc:bus-jpeg ( 75000 KHz ~ 300000 KHz)
[    4.022984] exynos-bus: new bus device registered: soc:bus-jpeg-apb ( 83250 KHz ~ 166500 KHz)
[    4.032038] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    4.036087] exynos-bus: new bus device registered: soc:bus-disp1-fimd (120000 KHz ~ 200000 KHz)
[    4.050186] exynos-bus: new bus device registered: soc:bus-disp1 (120000 KHz ~ 300000 KHz)
[    4.059443] exynos-bus: new bus device registered: soc:bus-gscl-scaler (150000 KHz ~ 300000 KHz)
[    4.069378] exynos-bus: new bus device registered: soc:bus-mscl ( 84000 KHz ~ 666000 KHz)
[    4.128156] ALSA device list:
[    4.132548]   #0: ODROID-XU4
[    4.139917] Freeing unused kernel image (initmem) memory: 2048K
[    4.163030] Run /init as init process
Loading, please wait...
[    4.236746] usb 3-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=92.22
[    4.248013] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.258476] usb 3-1: Product: USB2.0 Hub
[    4.265576] usb 3-1: Manufacturer: GenesysLogic
[    4.330268] hub 3-1:1.0: USB hub found
[    4.340790] hub 3-1:1.0: 2 ports detected
Starting version 249.11-0ubuntu3.12
[    4.393412] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[    4.435076] usb 4-1: New USB device found, idVendor=05e3, idProduct=0616, bcdDevice=92.22
[    4.444169] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.451709] usb 4-1: Product: USB3.0 Hub
[    4.456035] usb 4-1: Manufacturer: GenesysLogic
[    4.490141] hub 4-1:1.0: USB hub found
[    4.495125] hub 4-1:1.0: 2 ports detected
[    4.962139] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd
[    5.002923] usb 6-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00
[    5.011473] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    5.019188] usb 6-1: Product: USB 10/100/1000 LAN
[    5.024270] usb 6-1: Manufacturer: Realtek
[    5.028706] usb 6-1: SerialNumber: 000001000000
[    5.264258] r8152-cfgselector 6-1: reset SuperSpeed USB device number 2 using xhci-hcd
[    5.347547] r8152 6-1:1.0: load rtl8153a-3 v2 02/07/20 successfully
[    5.432526] r8152 6-1:1.0 eth0: v1.12.13
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.37.2
[/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk1p2] fsck.ext4 -y -C0 /dev/mmcblk1p2 
e2fsck 1.46.5 (30-Dec-2021)
rootfs: clean, 50288/3809280 files, 778754/15234560 blocks
done.
[    5.831334] EXT4-fs (mmcblk1p2): mounted filesystem without journal. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    6.374824] systemd[1]: systemd 249.11-0ubuntu3.12 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    6.414386] systemd[1]: Detected architecture arm.

Welcome to [1B][1mUbuntu 22.04.3 LTS[1B][0m!

[    6.455726] systemd[1]: Hostname set to <odroid>.
[    8.062003] random: crng init done
[    8.069048] systemd[1]: Queued start job for default target Graphical Interface.
[    8.128173] systemd[1]: Created slice Slice /system/modprobe.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/modprobe[1B][0m.
[    8.178148] systemd[1]: Created slice Slice /system/serial-getty.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/serial-getty[1B][0m.
[    8.228274] systemd[1]: Created slice Slice /system/systemd-fsck.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/systemd-fsck[1B][0m.
[    8.275631] systemd[1]: Created slice User and Session Slice.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mUser and Session Slice[1B][0m.
[    8.324400] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDispatch Password …ts to Console Directory Watch[1B][0m.
[    8.373481] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mForward Password R…uests to Wall Directory Watch[1B][0m.
[    8.426302] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[[1B][0;32m  OK  [1B][0m] Set up automount [1B][0;1;39mArbitrary…s File System Automount Point[1B][0m.
[    8.473277] systemd[1]: Reached target Local Encrypted Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Encrypted Volumes[1B][0m.
[    8.512255] systemd[1]: Reached target Path Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPath Units[1B][0m.
[    8.552691] systemd[1]: Reached target Remote File Systems.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mRemote File Systems[1B][0m.
[    8.593241] systemd[1]: Reached target Slice Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSlice Units[1B][0m.
[    8.653248] systemd[1]: Reached target Swaps.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSwaps[1B][0m.
[    8.703021] systemd[1]: Reached target Local Verity Protected Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Verity Protected Volumes[1B][0m.
[    8.765488] systemd[1]: Listening on Syslog Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mSyslog Socket[1B][0m.
[    8.824925] systemd[1]: Listening on fsck to fsckd communication Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mfsck to fsckd communication Socket[1B][0m.
[    8.884058] systemd[1]: Listening on initctl Compatibility Named Pipe.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39minitctl Compatibility Named Pipe[1B][0m.
[    8.945881] systemd[1]: Listening on Journal Audit Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Audit Socket[1B][0m.
[    8.996532] systemd[1]: Listening on Journal Socket (/dev/log).
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket (/dev/log)[1B][0m.
[    9.054870] systemd[1]: Listening on Journal Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket[1B][0m.
[    9.108861] systemd[1]: Listening on udev Control Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Control Socket[1B][0m.
[    9.164480] systemd[1]: Listening on udev Kernel Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Kernel Socket[1B][0m.
[    9.213068] systemd[1]: Reached target Socket Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSocket Units[1B][0m.
[    9.264288] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[    9.333013] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting [1B][0;1;39mPOSIX Message Queue File System[1B][0m...
[    9.386989] systemd[1]: Mounting Kernel Debug File System...
         Mounting [1B][0;1;39mKernel Debug File System[1B][0m...
[    9.429562] systemd[1]: Mounting Kernel Trace File System...
         Mounting [1B][0;1;39mKernel Trace File System[1B][0m...
[    9.481820] systemd[1]: Starting Journal Service...
         Starting [1B][0;1;39mJournal Service[1B][0m...
[    9.527760] systemd[1]: Starting Set the console keyboard layout...
         Starting [1B][0;1;39mSet the console keyboard layout[1B][0m...
[    9.562205] systemd[1]: Condition check resulted in Create List of Static Device Nodes being skipped.
[    9.575672] systemd[1]: Starting Load Kernel Module configfs...
         Starting [1B][0;1;39mLoad Kernel Module configfs[1B][0m...
[    9.615846] systemd[1]: Starting Load Kernel Module drm...
         Starting [1B][0;1;39mLoad Kernel Module drm[1B][0m...
[    9.655697] systemd[1]: Starting Load Kernel Module efi_pstore...
         Starting [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m...
[    9.697358] systemd[1]: Starting Load Kernel Module fuse...
         Starting [1B][0;1;39mLoad Kernel Module fuse[1B][0m...
[    9.732415] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    9.747621] systemd[1]: Starting Load Kernel Modules...
         Starting [1B][0;1;39mLoad Kernel Modules[1B][0m...
[    9.785523] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m...
[    9.827344] EXT4-fs (mmcblk1p2): re-mounted. Quota mode: none.
[    9.828836] systemd[1]: Starting Coldplug All udev Devices...
         Starting [1B][0;1;39mColdplug All udev Devices[1B][0m...
[    9.899400] systemd[1]: Started Journal Service.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mJournal Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mPOSIX Message Queue File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Debug File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Trace File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet the console keyboard layout[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module configfs[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module drm[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module fuse[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Modules[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m.
         Mounting [1B][0;1;39mKernel Configuration File System[1B][0m...
         Starting [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m...
[   10.495362] systemd-journald[251]: Received client request to flush runtime journal.
         Starting [1B][0;1;39mLoad/Save Random Seed[1B][0m...
         Starting [1B][0;1;39mApply Kernel Variables[1B][0m...
         Starting [1B][0;1;39mCreate System Users[1B][0m...
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Configuration File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad/Save Random Seed[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mApply Kernel Variables[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mColdplug All udev Devices[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate System Users[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m.
         Starting [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPreparation for Local File Systems[1B][0m.
         Starting [1B][0;1;39mRule-based Manage…for Device Events and Files[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mRule-based Manager for Device Events and Files[1B][0m.
[   12.171285] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[   12.182557] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[   12.182664] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[   12.182674] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[[1B][0;32m  OK  [1B][[   12.195120] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
0m] Found device [1B][0;1;39m/dev/t[   12.228849] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
tySAC2[1B][0m.
[   12.239941] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[   12.253261] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSound Card[1B][0m.
[   12.492105] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[   12.506570] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[   12.532123] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[   12.544704] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[[1B][0;32m  OK  [1B][0m] Removed slice [1B][0;1;39mSlice /system/modprobe[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mSound Card[1B][0m.
         Stopping [1B][0;1;39mLoad/Save Random Seed[1B][0m...
[[1B][0;32m  OK  [1B][0m] Removed slice [1B][0;1;39mSlice /system/serial-getty[1B][0m.
[   12.772131] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[   12.785277] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mRemote File Systems[1B][0m.
[   12.812070] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[   12.827112] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
         Starting [1B][0;1;39mSet console scheme[1B][0m...
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mPath Units[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mSlice Units[1B][0m.
[[1B][0;32m  OK  [1B][0m] Removed slice [1B][0;1;39mUser and Session Slice[1B][0m.
[   13.052191] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[   13.052230] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[   13.102111] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[   13.102135] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mSocket Units[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mLocal Encrypted Volumes[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mDispatch Password …ts to Console Directory Watch[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mForward Password R…uests to Wall Directory Watch[1B][0m.
[   13.312225] thermal thermal_zone1: cpu1-thermal: critical temperature reached, shutting down
[   13.330704] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mSwaps[1B][0m.
[   13.362156] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[   13.375439] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[   13.387191] thermal thermal_zone0: cpu0-thermal: critical temperature reached, shutting down
[   13.400799] reboot: HARDWARE PROTECTION shutdown (Temperature too high)
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mLocal Verity Protected Volumes[1B][0m.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mD-Bus System Message Bus Socket[1B][0m.
[[1B][0;32m  OK  [1B][0m] Closed [1B][0;1;39mSyslog Socket[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mD-Bus System Message Bus[1B][0m.
[[1B][0;32m  OK  [1B][0m] Unset automount [1B][0;1;39mArbitrary …s File System Automount Point[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mApply Kernel Variables[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mLoad Kernel Modules[1B][0m.
         Unmounting [1B][0;1;39m/run/credentials/systemd-sysusers.service[1B][0m...
         Starting [1B][0;1;39mSet console font and keymap[1B][0m...
[[1B][0;32m  OK  [1B][0m] Removed slice [1B][0;1;39mSlice /system/systemd-fsck[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mLoad/Save Random Seed[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console scheme[1B][0m.
[[1B][0;32m  OK  [1B][0m] Unmounted [1B][0;1;39m/run/credentials/systemd-sysusers.service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console font and keymap[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped target [1B][0;1;39mPreparation for Local File Systems[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mUnmount All Filesystems[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mCreate System Users[1B][0m.
[[1B][0;32m  OK  [1B][0m] Stopped [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Shutdown[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLate Shutdown Services[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSystem Power Off[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Power Off[1B][0m.
[   15.734192] reboot: Power down
[00]

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

Got it!
Try again, I reuploaded a different zImage that should help you.

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Aaha. Ok. It looks good now.

Code: Select all

[00]

U-Boot 2017.05-00008-g6a9ddb8303-dirty (May 19 2020 - 19:48:01 +0900) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz
Model: Odroid XU4 based on EXYNOS5422
Board: Odroid XU4 based on EXYNOS5422
Type:  xu4
DRAM:  2 GiB
MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
MMC Device 0 ( SD ): 58.2 GiB
mmc_init: -5, time 4
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Press quickly 'Enter' twice to stop autoboot:  0 
reading /boot.ini
2365 bytes read in 4 ms (577.1 KiB/s)
## Executing script at 43e00000
reading config.ini
6911 bytes read in 5 ms (1.3 MiB/s)
ini: Imported macaddr as 00:1e:06:61:7a:39
ini: Imported vout as hdmi
ini: Imported HPD as true
ini: Imported cecenable as false
ini: Imported disable_vu7 as false
ini: Imported ddr_freq as 825
ini: Imported overlay_resize as 16384
ini: Imported overlay_profile as 
ini: Imported overlays as spi0 i2c0 i2c1 uart0
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
reading zImage
7142120 bytes read in 481 ms (14.2 MiB/s)
reading uInitrd
8838868 bytes read in 591 ms (14.3 MiB/s)
reading exynos5422-odroidxu4.dtb
88559 bytes read in 12 ms (7 MiB/s)
reading overlays/spi0.dtbo
691 bytes read in 7 ms (95.7 KiB/s)
reading overlays/i2c0.dtbo
224 bytes read in 5 ms (43 KiB/s)
reading overlays/i2c1.dtbo
226 bytes read in 6 ms (36.1 KiB/s)
reading overlays/uart0.dtbo
227 bytes read in 6 ms (36.1 KiB/s)
Kernel image @ 0x40008000 [ 0x000000 - 0x6cfae8 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8838804 Bytes = 8.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 44000000
   Booting using the fdt blob at 0x44000000
   reserving fdt memory region: addr=44000000 size=2c000
   Using Device Tree in place at 44000000, end 4402efff

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 6.1.75+ (mdrjr@powah) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #17 SMP PREEMPT Wed Feb  7 14:56:19 -03 2024
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel ODROID XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0x00000000b6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000040000000-0x000000006fffffff]
[    0.000000]   HighMem  [mem 0x0000000070000000-0x00000000be9fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Running under secure firmware.
[    0.000000] percpu: Embedded 17 pages/cpu s39124 r8192 d22316 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false
[    0.000000] hdmi: using HDMI mode
[    0.000000] Unknown kernel command line parameters "false HPD=true vout=hdmi", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1895044K/2074624K available (12288K kernel code, 1125K rwdata, 2884K rodata, 2048K init, 365K bss, 48508K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000031] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57
[    0.001526] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.001551] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.001572] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001588] Ignoring duplicate/late registration of read_current_timer delay
[    0.002384] Console: colour dummy device 80x30
[    0.003139] printk: console [tty1] enabled
[    0.003206] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003254] CPU: Testing write buffer coherency: ok
[    0.003343] pid_max: default: 32768 minimum: 301
[    0.003494] LSM: Security Framework initializing
[    0.003690] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003744] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005492] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.006911] cblist_init_generic: Setting adjustable number of callback queues.
[    0.006956] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007148] cblist_init_generic: Setting adjustable number of callback queues.
[    0.007184] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007393] Setting up static identity map for 0x40200000 - 0x40200060
[    0.007741] ARM CCI driver probed
[    0.008331] Exynos MCPM support installed
[    0.008737] rcu: Hierarchical SRCU implementation.
[    0.008764] rcu: 	Max phase no-delay instances is 1000.
[    0.010045] smp: Bringing up secondary CPUs ...
[    0.011202] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.012503] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.013732] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.014931] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.014948] CPU4: detected I-Cache line size mismatch, workaround enabled
[    0.014956] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.015046] CPU4: Spectre BHB: enabling loop workaround for all CPUs
[    0.016320] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.016334] CPU5: detected I-Cache line size mismatch, workaround enabled
[    0.016341] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.017654] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.017668] CPU6: detected I-Cache line size mismatch, workaround enabled
[    0.017676] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.018949] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.018963] CPU7: detected I-Cache line size mismatch, workaround enabled
[    0.018971] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.019207] smp: Brought up 1 node, 8 CPUs
[    0.019270] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.019301] CPU: All CPU(s) started in HYP mode.
[    0.019323] CPU: Virtualization extensions available.
[    0.020782] devtmpfs: initialized
[    0.042037] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.042319] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.042360] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.045506] pinctrl core: initialized pinctrl subsystem
[    0.048412] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.052101] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.053840] audit: initializing netlink subsys (disabled)
[    0.054119] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1
[    0.054697] thermal_sys: Registered thermal governor 'step_wise'
[    0.054974] cpuidle: using governor menu
[    0.055443] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.055472] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.185953] EXYNOS5420 PMU initialized
[    0.303841] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.305768] fbcon: Taking over console
[    0.307526] iommu: Default domain type: Translated 
[    0.307550] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.307952] usbcore: registered new interface driver usbfs
[    0.308020] usbcore: registered new interface driver hub
[    0.308088] usbcore: registered new device driver usb
[    0.308816] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.308846] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.309212] s3c-i2c 12c70000.i2c: i2c-0: S3C I2C adapter
[    0.309426] s3c-i2c 12c80000.i2c: slave address 0x00
[    0.309454] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[    0.309750] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[    0.310238] mc: Linux media interface: v0.10
[    0.310317] videodev: Linux video capture interface: v2.00
[    0.310933] Advanced Linux Sound Architecture Driver Initialized.
[    0.311967] clocksource: Switched to clocksource mct-frc
[    0.312444] VFS: Disk quotas dquot_6.6.0
[    0.312522] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.325779] NET: Registered PF_INET protocol family
[    0.326044] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.327892] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.327944] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.327977] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.328131] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.328436] TCP: Hash tables configured (established 8192 bind 8192)
[    0.328557] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.328618] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.328871] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.328933] NET: Registered PF_XDP protocol family
[    0.329471] Trying to unpack rootfs image as initramfs...
[    0.342209] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.343408] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.345535] Initialise system trusted keyrings
[    0.345888] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.355358] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.441883] NET: Registered PF_ALG protocol family
[    0.441922] Key type asymmetric registered
[    0.441944] Asymmetric key parser 'x509' registered
[    0.442221] bounce: pool size: 64 pages
[    0.442371] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.442770] io scheduler mq-deadline registered
[    0.442798] io scheduler kyber registered
[    0.443061] io scheduler bfq registered
[    0.444771] samsung-pinctrl 13400000.pinctrl: Failed to create device link (0x180) with soc
[    0.447107] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator
[    0.448117] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator
[    0.448292] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator
[    0.448720] exynos5_usb3drd_phy 12500000.phy: supply vbus not found, using dummy regulator
[    0.448904] exynos5_usb3drd_phy 12500000.phy: supply vbus-boost not found, using dummy regulator
[    0.457293] dma-pl330 3880000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.457330] dma-pl330 3880000.dma-controller: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.460525] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.460559] dma-pl330 121a0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.463803] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.463836] dma-pl330 121b0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.465090] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.465123] dma-pl330 10800000.dma-controller: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.482029] dma-pl330 3880000.dma-controller: PM domain MAU will not be powered off
[    0.548539] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.551159] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 124, base_baud = 0) is a S3C6400/10
[    0.551712] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 125, base_baud = 0) is a S3C6400/10
[    1.575490] printk: console [ttySAC2] enabled
[    1.582011] exynos-trng 10830600.rng: Exynos True Random Number Generator.
[    1.589124] exynos-mixer 14450000.mixer: Adding to iommu group 0
[    1.596636] exynos-drm-g2d 10850000.g2d: Adding to iommu group 1
[    1.603143] exynos-rotator 11c00000.rotator: Adding to iommu group 2
[    1.609282] exynos-scaler 12800000.scaler: Adding to iommu group 3
[    1.615942] exynos-scaler 12810000.scaler: Adding to iommu group 4
[    1.622398] exynos-scaler 12820000.scaler: Adding to iommu group 5
[    1.629054] exynos-drm-gsc 13e00000.video-scaler: Adding to iommu group 6
[    1.635286] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered successfully.
[    1.642409] exynos-drm-gsc 13e10000.video-scaler: Adding to iommu group 7
[    1.649495] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered successfully.
[    1.673999] brd: module loaded
[    1.676793] usbcore: registered new device driver r8152-cfgselector
[    1.681878] usbcore: registered new interface driver r8152
[    1.687382] usbcore: registered new interface driver ax88179_178a
[    1.693420] usbcore: registered new interface driver cdc_ether
[    1.699198] usbcore: registered new interface driver cdc_subset
[    1.705142] usbcore: registered new interface driver r8153_ecm
[    1.713882] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.719382] exynos-ehci 12110000.usb: EHCI Host Controller
[    1.724889] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    1.733107] exynos-ehci 12110000.usb: irq 133, io mem 0x12110000
[    1.762033] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    1.766796] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.774857] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.782042] usb usb1: Product: EHCI Host Controller
[    1.786852] usb usb1: Manufacturer: Linux 6.1.75+ ehci_hcd
[    1.792341] usb usb1: SerialNumber: 12110000.usb
[    1.797652] hub 1-0:1.0: USB hub found
[    1.800669] hub 1-0:1.0: 3 ports detected
[    1.806070] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.811564] exynos-ohci 12120000.usb: USB Host Controller
[    1.816985] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    1.824918] exynos-ohci 12120000.usb: irq 133, io mem 0x12120000
[    1.896259] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    1.903107] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.910251] usb usb2: Product: USB Host Controller
[    1.915051] usb usb2: Manufacturer: Linux 6.1.75+ ohci_hcd
[    1.920473] usb usb2: SerialNumber: 12120000.usb
[    1.925801] hub 2-0:1.0: USB hub found
[    1.928830] hub 2-0:1.0: 3 ports detected
[    1.935413] mousedev: PS/2 mouse device common for all mice
[    1.941245] i2c_dev: i2c /dev entries driver
[    1.968502] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    1.985067] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[    2.004484] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.074178] s5m-rtc s2mps14-rtc: registered as rtc0
[    2.079437] s5m-rtc s2mps14-rtc: setting system clock to 2024-02-07T17:59:05 UTC (1707328745)
[    2.086897] s2mps11-clk s2mps11-clk: DMA mask not set
[    2.101843] exynos-tmu 10060000.tmu: More trip points than supported by this TMU.
[    2.107916] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode.
[    2.117803] exynos-tmu 10064000.tmu: More trip points than supported by this TMU.
[    2.123861] exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode.
[    2.133778] exynos-tmu 10068000.tmu: More trip points than supported by this TMU.
[    2.139794] exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode.
[    2.149808] exynos-tmu 1006c000.tmu: More trip points than supported by this TMU.
[    2.155865] exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode.
[    2.165869] exynos-tmu 100a0000.tmu: More trip points than supported by this TMU.
[    2.171891] exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode.
[    2.181236] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    2.188985] device-mapper: uevent: version 1.0.3
[    2.193200] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    2.217219] sdhci: Secure Digital Host Controller Interface driver
[    2.221942] sdhci: Copyright(c) Pierre Ossman
[    2.226880] Synopsys Designware Multimedia Card Interface Driver
[    2.233956] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    2.233988] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    2.246443] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    2.252704] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    2.252998] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    2.253729] s5p-secss 10830000.sss: s5p-sss driver registered
[    2.256697] hid: raw HID events driver (C) Jiri Kosina
[    2.258330] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 144,64 bit host data width,64 deep fifo
[    2.264459] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    2.273515] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    2.275696] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 145,64 bit host data width,64 deep fifo
[    2.305619] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.320062] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    2.321857] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.326265] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    2.341441] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    2.348041] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    2.355052] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0-0)
[    2.362550] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0-1)
[    2.370393] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1-0)
[    2.378318] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1-1)
[    2.388946] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_0 not found
[    2.395434] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_1 not found
[    2.403656] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0
[    2.408009] mmc_host mmc1: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
[    2.424309] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s
[    2.432107] NET: Registered PF_PACKET protocol family
[    2.435700] NET: Registered PF_KEY protocol family
[    2.441141] Key type dns_resolver registered
[    2.445282] Registering SWP/SWPB emulation handler
[    2.449999] registered taskstats version 1
[    2.453592] Loading compiled-in X.509 certificates
[    2.459029] Key type .fscrypt registered
[    2.462239] Key type fscrypt-provisioning registered
[    2.524291] mmc1: new ultra high speed SDR104 SDXC card at address 0001
[    2.531385] mmcblk1: mmc1:0001 SD64G 58.2 GiB 
[    2.540090]  mmcblk1: p1 p2
[    2.742240] usb 2-1: new full-speed USB device number 2 using exynos-ohci
[    3.018304] usb 2-1: New USB device found, idVendor=046a, idProduct=010e, bcdDevice= 0.13
[    3.025422] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    3.032379] usb 2-1: Product: USB Wireless Device
[    3.095194] Freeing initrd memory: 8632K
[    3.128302] Key type encrypted registered
[    3.185236] exynos-chipid 10000000.chipid: cpu0 opp0, freq: 1500 missing
[    3.190507] exynos-chipid 10000000.chipid: cpu4 opp0, freq: 2100 missing
[    3.197191] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5800] PRO_ID[0xe5422000] REV[0x1] Detected
[    3.211281] OF: graph: no port node found in /soc/hdmi@14530000
[    3.218363] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[    3.224790] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0e7bc8c)
[    3.231328] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc0e7c26c)
[    3.238145] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully registered.
[    3.246217] exynos-drm exynos-drm: bound 10850000.g2d (ops 0xc0e7d27c)
[    3.252705] exynos-rotator 11c00000.rotator: The exynos rotator has been probed successfully
[    3.261074] exynos-drm exynos-drm: bound 11c00000.rotator (ops 0xc0e7db08)
[    3.267959] exynos-scaler 12800000.scaler: The exynos scaler has been probed successfully
[    3.276092] exynos-drm exynos-drm: bound 12800000.scaler (ops 0xc0e7e250)
[    3.282854] exynos-scaler 12810000.scaler: The exynos scaler has been probed successfully
[    3.290967] exynos-drm exynos-drm: bound 12810000.scaler (ops 0xc0e7e250)
[    3.297769] exynos-scaler 12820000.scaler: The exynos scaler has been probed successfully
[    3.305902] exynos-drm exynos-drm: bound 12820000.scaler (ops 0xc0e7e250)
[    3.312661] exynos-drm-gsc 13e00000.video-scaler: The exynos gscaler has been probed successfully
[    3.321470] exynos-drm exynos-drm: bound 13e00000.video-scaler (ops 0xc0e7eb24)
[    3.328806] exynos-drm-gsc 13e10000.video-scaler: The exynos gscaler has been probed successfully
[    3.337643] exynos-drm exynos-drm: bound 13e10000.video-scaler (ops 0xc0e7eb24)
[    3.518153] Console: switching to colour frame buffer device 240x75
[    3.569999] exynos-drm exynos-drm: [drm] fb0: exynosdrmfb frame buffer device
[    3.580031] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 0
[    3.589692] mali 11800000.gpu: GPU identified as 0x0620 r0p1 status 0
[    3.594843] mali 11800000.gpu: Protected mode not available
[    3.601523] mali 11800000.gpu: Probed as mali0
[    3.607571] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.611651] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[    3.619895] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.628817] xhci-hcd xhci-hcd.8.auto: irq 153, io mem 0x12000000
[    3.634976] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.640091] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[    3.647772] xhci-hcd xhci-hcd.8.auto: Host supports USB 3.0 SuperSpeed
[    3.654432] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.662512] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.669647] usb usb3: Product: xHCI Host Controller
[    3.674514] usb usb3: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.679919] usb usb3: SerialNumber: xhci-hcd.8.auto
[    3.685499] hub 3-0:1.0: USB hub found
[    3.688489] hub 3-0:1.0: 1 port detected
[    3.692708] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.700546] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.708704] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.715886] usb usb4: Product: xHCI Host Controller
[    3.720707] usb usb4: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.726244] usb usb4: SerialNumber: xhci-hcd.8.auto
[    3.731617] hub 4-0:1.0: USB hub found
[    3.734802] hub 4-0:1.0: 1 port detected
[    3.741530] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.745606] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    3.753663] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.762779] xhci-hcd xhci-hcd.9.auto: irq 154, io mem 0x12400000
[    3.768754] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.774043] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 6
[    3.781652] xhci-hcd xhci-hcd.9.auto: Host supports USB 3.0 SuperSpeed
[    3.788322] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.796420] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.803599] usb usb5: Product: xHCI Host Controller
[    3.808405] usb usb5: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.813899] usb usb5: SerialNumber: xhci-hcd.9.auto
[    3.819291] hub 5-0:1.0: USB hub found
[    3.822471] hub 5-0:1.0: 1 port detected
[    3.826727] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.834587] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.842683] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.849856] usb usb6: Product: xHCI Host Controller
[    3.856986] usb usb6: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.863269] usb usb6: SerialNumber: xhci-hcd.9.auto
[    3.869374] hub 6-0:1.0: USB hub found
[    3.873926] hub 6-0:1.0: 1 port detected
[    3.880840] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[    3.887311] s3c-rtc 101e0000.rtc: registered as rtc1
[    3.894743] exynos-bus: new bus device registered: soc:bus-wcore ( 88700 KHz ~ 532000 KHz)
[    3.904304] exynos-bus: new bus device registered: soc:bus-noc ( 66600 KHz ~ 111000 KHz)
[    3.913553] exynos-bus: new bus device registered: soc:bus-fsys-apb (111000 KHz ~ 222000 KHz)
[    3.923199] exynos-bus: new bus device registered: soc:bus-fsys2 ( 75000 KHz ~ 200000 KHz)
[    3.932752] exynos-bus: new bus device registered: soc:bus-mfc ( 83250 KHz ~ 333000 KHz)
[    3.942027] exynos-bus: new bus device registered: soc:bus-gen ( 88700 KHz ~ 266000 KHz)
[    3.951005] exynos-bus: new bus device registered: soc:bus-peri ( 66600 KHz ~  66600 KHz)
[    3.960421] exynos-bus: new bus device registered: soc:bus-g2d ( 83250 KHz ~ 333000 KHz)
[    3.969742] exynos-bus: new bus device registered: soc:bus-g2d-acp ( 66500 KHz ~ 266000 KHz)
[    3.979313] exynos-bus: new bus device registered: soc:bus-jpeg ( 75000 KHz ~ 300000 KHz)
[    3.988654] exynos-bus: new bus device registered: soc:bus-jpeg-apb ( 83250 KHz ~ 166500 KHz)
[    3.992242] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    3.998328] exynos-bus: new bus device registered: soc:bus-disp1-fimd (120000 KHz ~ 200000 KHz)
[    4.017115] exynos-bus: new bus device registered: soc:bus-disp1 (120000 KHz ~ 300000 KHz)
[    4.026341] exynos-bus: new bus device registered: soc:bus-gscl-scaler (150000 KHz ~ 300000 KHz)
[    4.036274] exynos-bus: new bus device registered: soc:bus-mscl ( 84000 KHz ~ 666000 KHz)
[    4.099478] ALSA device list:
[    4.106671]   #0: ODROID-XU4
[    4.120548] Freeing unused kernel image (initmem) memory: 2048K
[    4.132424] Run /init as init process
Loading, please wait...
[    4.196977] usb 3-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=92.22
[    4.206124] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.214272] usb 3-1: Product: USB2.0 Hub
[    4.219054] usb 3-1: Manufacturer: GenesysLogic
[    4.263203] hub 3-1:1.0: USB hub found
[    4.274084] hub 3-1:1.0: 2 ports detected
Starting version 249.11-0ubuntu3.12
[    4.342353] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[    4.395297] usb 4-1: New USB device found, idVendor=05e3, idProduct=0616, bcdDevice=92.22
[    4.404444] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.412440] usb 4-1: Product: USB3.0 Hub
[    4.417398] usb 4-1: Manufacturer: GenesysLogic
[    4.455086] hub 4-1:1.0: USB hub found
[    4.460011] hub 4-1:1.0: 2 ports detected
[    4.932147] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd
[    4.962804] usb 6-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00
[    4.971544] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    4.979594] usb 6-1: Product: USB 10/100/1000 LAN
[    4.984848] usb 6-1: Manufacturer: Realtek
[    4.989365] usb 6-1: SerialNumber: 000001000000
[    5.229198] r8152-cfgselector 6-1: reset SuperSpeed USB device number 2 using xhci-hcd
[    5.311854] r8152 6-1:1.0: load rtl8153a-3 v2 02/07/20 successfully
[    5.392557] r8152 6-1:1.0 eth0: v1.12.13
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.37.2
[/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk1p2] fsck.ext4 -y -C0 /dev/mmcblk1p2 
e2fsck 1.46.5 (30-Dec-2021)
rootfs: clean, 50288/3809280 files, 778755/15234560 blocks
done.
[    5.826948] EXT4-fs (mmcblk1p2): mounted filesystem without journal. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    6.382564] systemd[1]: systemd 249.11-0ubuntu3.12 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    6.418196] systemd[1]: Detected architecture arm.

Welcome to [1B][1mUbuntu 22.04.3 LTS[1B][0m!

[    6.453444] systemd[1]: Hostname set to <odroid>.
[    8.001986] random: crng init done
[    8.009094] systemd[1]: Queued start job for default target Graphical Interface.
[    8.087928] systemd[1]: Created slice Slice /system/modprobe.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/modprobe[1B][0m.
[    8.140155] systemd[1]: Created slice Slice /system/serial-getty.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/serial-getty[1B][0m.
[    8.186729] systemd[1]: Created slice Slice /system/systemd-fsck.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/systemd-fsck[1B][0m.
[    8.238405] systemd[1]: Created slice User and Session Slice.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mUser and Session Slice[1B][0m.
[    8.284435] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDispatch Password …ts to Console Directory Watch[1B][0m.
[    8.334182] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mForward Password R…uests to Wall Directory Watch[1B][0m.
[    8.386735] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[[1B][0;32m  OK  [1B][0m] Set up automount [1B][0;1;39mArbitrary…s File System Automount Point[1B][0m.
[    8.433562] systemd[1]: Reached target Local Encrypted Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Encrypted Volumes[1B][0m.
[    8.483892] systemd[1]: Reached target Path Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPath Units[1B][0m.
[    8.533095] systemd[1]: Reached target Remote File Systems.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mRemote File Systems[1B][0m.
[    8.583069] systemd[1]: Reached target Slice Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSlice Units[1B][0m.
[    8.622148] systemd[1]: Reached target Swaps.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSwaps[1B][0m.
[    8.653013] systemd[1]: Reached target Local Verity Protected Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Verity Protected Volumes[1B][0m.
[    8.705482] systemd[1]: Listening on Syslog Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mSyslog Socket[1B][0m.
[    8.754956] systemd[1]: Listening on fsck to fsckd communication Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mfsck to fsckd communication Socket[1B][0m.
[    8.803814] systemd[1]: Listening on initctl Compatibility Named Pipe.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39minitctl Compatibility Named Pipe[1B][0m.
[    8.855312] systemd[1]: Listening on Journal Audit Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Audit Socket[1B][0m.
[    8.903197] systemd[1]: Listening on Journal Socket (/dev/log).
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket (/dev/log)[1B][0m.
[    8.945778] systemd[1]: Listening on Journal Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket[1B][0m.
[    8.999005] systemd[1]: Listening on udev Control Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Control Socket[1B][0m.
[    9.053918] systemd[1]: Listening on udev Kernel Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Kernel Socket[1B][0m.
[    9.102937] systemd[1]: Reached target Socket Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSocket Units[1B][0m.
[    9.156069] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[    9.254253] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting [1B][0;1;39mPOSIX Message Queue File System[1B][0m...
[    9.322046] systemd[1]: Mounting Kernel Debug File System...
         Mounting [1B][0;1;39mKernel Debug File System[1B][0m...
[    9.380871] systemd[1]: Mounting Kernel Trace File System...
         Mounting [1B][0;1;39mKernel Trace File System[1B][0m...
[    9.447143] systemd[1]: Starting Journal Service...
         Starting [1B][0;1;39mJournal Service[1B][0m...
[    9.498922] systemd[1]: Starting Set the console keyboard layout...
         Starting [1B][0;1;39mSet the console keyboard layout[1B][0m...
[    9.542218] systemd[1]: Condition check resulted in Create List of Static Device Nodes being skipped.
[    9.555558] systemd[1]: Starting Load Kernel Module configfs...
         Starting [1B][0;1;39mLoad Kernel Module configfs[1B][0m...
[    9.595727] systemd[1]: Starting Load Kernel Module drm...
         Starting [1B][0;1;39mLoad Kernel Module drm[1B][0m...
[    9.635507] systemd[1]: Starting Load Kernel Module efi_pstore...
         Starting [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m...
[    9.684822] systemd[1]: Starting Load Kernel Module fuse...
         Starting [1B][0;1;39mLoad Kernel Module fuse[1B][0m...
[    9.722497] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    9.737333] systemd[1]: Starting Load Kernel Modules...
         Starting [1B][0;1;39mLoad Kernel Modules[1B][0m...
[    9.775311] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m...
[    9.830234] systemd[1]: Starting Coldplug All udev Devices...
         Starting [1B][0;1;39mColdplug All udev Devices[1B][0m...
[    9.877726] EXT4-fs (mmcblk1p2): re-mounted. Quota mode: none.
[    9.918695] systemd[1]: Started Journal Service.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mJournal Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mPOSIX Message Queue File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Debug File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Trace File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet the console keyboard layout[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module configfs[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module drm[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module fuse[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Modules[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m.
         Mounting [1B][0;1;39mKernel Configuration File System[1B][0m...
         Starting [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m...
[   10.499874] systemd-journald[253]: Received client request to flush runtime journal.
         Starting [1B][0;1;39mLoad/Save Random Seed[1B][0m...
         Starting [1B][0;1;39mApply Kernel Variables[1B][0m...
         Starting [1B][0;1;39mCreate System Users[1B][0m...
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Configuration File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad/Save Random Seed[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mApply Kernel Variables[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mColdplug All udev Devices[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate System Users[1B][0m.
         Starting [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPreparation for Local File Systems[1B][0m.
         Starting [1B][0;1;39mRule-based Manage…for Device Events and Files[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mRule-based Manager for Device Events and Files[1B][0m.
[[1B][0;32m  OK  [1B][0m] Found device [1B][0;1;39m/dev/ttySAC2[1B][0m.
[[1B][0;32m  OK  [1B][0m] Found device [1B][0;1;39m/dev/disk/by-label/boot[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSound Card[1B][0m.
         Starting [1B][0;1;39mFile System Check on /dev/disk/by-label/boot[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mFile System Check Daemon to report status[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mFile System Check on /dev/disk/by-label/boot[1B][0m.
         Mounting [1B][0;1;39m/media/boot[1B][0m...
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39m/media/boot[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal File Systems[1B][0m.
         Starting [1B][0;1;39mSet console font and keymap[1B][0m...
         Starting [1B][0;1;39mSet Up Additional Binary Formats[1B][0m...
         Starting [1B][0;1;39mCreate Volatile Files and Directories[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console font and keymap[1B][0m.
         Mounting [1B][0;1;39mArbitrary Executable File Formats File System[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate Volatile Files and Directories[1B][0m.
[[1B][0;1;31mFAILED[1B][0m] Failed to mount [1B][0;1;39mArbitrary …able File Formats File System[1B][0m.
See 'systemctl status proc-sys-fs-binfmt_misc.mount' for details.
         Starting [1B][0;1;39mNetwork Name Resolution[1B][0m...
         Starting [1B][0;1;39mNetwork Time Synchronization[1B][0m...
         Starting [1B][0;1;39mRecord System Boot/Shutdown in UTMP[1B][0m...
[[1B][0;1;31mFAILED[1B][0m] Failed to start [1B][0;1;39mSet Up Additional Binary Formats[1B][0m.
See 'systemctl status systemd-binfmt.service' for details.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRecord System Boot/Shutdown in UTMP[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Time Synchronization[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Initialization[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily Cleanup of Temporary Directories[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mBasic System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Time Set[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily apt download activities[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily apt upgrade and clean activities[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily dpkg database backup timer[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDiscard unused blocks once a week[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily rotation of log files[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily man-db regeneration[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mMessage of the Day[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mTimer Units[1B][0m.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mD-Bus System Message Bus Socket[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mRegular background program processing daemon[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mD-Bus System Message Bus[1B][0m.
         Starting [1B][0;1;39mNetwork Manager[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSave initial kernel messages after boot[1B][0m.
         Starting [1B][0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[1B][0m...
         Starting [1B][0;1;39mLSB: Load kernel …d to enable cpufreq scaling[1B][0m...
         Starting [1B][0;1;39mAuthorization Manager[1B][0m...
         Starting [1B][0;1;39mLSB: Run /etc/rc.local if it exist[1B][0m...
         Starting [1B][0;1;39mSystem Logging Service[1B][0m...
         Starting [1B][0;1;39mUser Login Management[1B][0m...
         Starting [1B][0;1;39mWPA supplicant[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Name Resolution[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSystem Logging Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mUser Login Management[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: Run /etc/rc.local if it exist[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mWPA supplicant[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mAuthorization Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: Load kernel m…ded to enable cpufreq scaling[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mNetwork[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mHost and Network Name Lookups[1B][0m.
         Starting [1B][0;1;39mModem Manager[1B][0m...
         Starting [1B][0;1;39mLSB: set CPUFreq kernel parameters[1B][0m...
         Starting [1B][0;1;39mODROID Specific System Tweaks[1B][0m...
         Starting [1B][0;1;39m/etc/rc.local Compatibility[1B][0m...
         Starting [1B][0;1;39mOpenBSD Secure Shell server[1B][0m...
         Starting [1B][0;1;39mHostname Service[1B][0m...
         Starting [1B][0;1;39mPermit User Sessions[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mODROID Specific System Tweaks[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39m/etc/rc.local Compatibility[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mPermit User Sessions[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mModem Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mHostname Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mOpenBSD Secure Shell server[1B][0m.
         Starting [1B][0;1;39mNetwork Manager Script Dispatcher Service[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSerial Getty on ttySAC2[1B][0m.
         Starting [1B][0;1;39mSet console scheme[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console scheme[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: set CPUFreq kernel parameters[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Manager Script Dispatcher Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/getty[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mGetty on tty1[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLogin Prompts[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mMulti-User System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mGraphical Interface[1B][0m.
         Starting [1B][0;1;39mRecord Runlevel Change in UTMP[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRecord Runlevel Change in UTMP[1B][0m.


Ubuntu 22.04.3 LTS odroid ttySAC2

odroid login: 

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Only the fan is always running now.

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

Got it, it was supposed to do that! It was a ugly hack.

I will prepare a different zImage now that will show me what your board is reporting so I can fix that.
These users thanked the author mdrjr for the post:
matty67 (Thu Feb 08, 2024 3:08 am)

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

Third time is the one!
Try again! hopefully this will fix your issues!
These users thanked the author mdrjr for the post:
matty67 (Thu Feb 08, 2024 3:44 am)

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

When I run stress-ng the fan starts to run but it not stops after stress-ng ends.



Here is the output:

Code: Select all

[00]

U-Boot 2017.05-00008-g6a9ddb8303-dirty (May 19 2020 - 19:48:01 +0900) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz
Model: Odroid XU4 based on EXYNOS5422
Board: Odroid XU4 based on EXYNOS5422
Type:  xu4
DRAM:  2 GiB
MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
MMC Device 0 ( SD ): 58.2 GiB
mmc_init: -5, time 3
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Press quickly 'Enter' twice to stop autoboot:  0 
reading /boot.ini
2365 bytes read in 4 ms (577.1 KiB/s)
## Executing script at 43e00000
reading config.ini
6911 bytes read in 5 ms (1.3 MiB/s)
ini: Imported macaddr as 00:1e:06:61:7a:39
ini: Imported vout as hdmi
ini: Imported HPD as true
ini: Imported cecenable as false
ini: Imported disable_vu7 as false
ini: Imported ddr_freq as 825
ini: Imported overlay_resize as 16384
ini: Imported overlay_profile as 
ini: Imported overlays as spi0 i2c0 i2c1 uart0
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
reading zImage
7141544 bytes read in 481 ms (14.2 MiB/s)
reading uInitrd
8838868 bytes read in 591 ms (14.3 MiB/s)
reading exynos5422-odroidxu4.dtb
88559 bytes read in 12 ms (7 MiB/s)
reading overlays/spi0.dtbo
691 bytes read in 6 ms (112.3 KiB/s)
reading overlays/i2c0.dtbo
224 bytes read in 6 ms (36.1 KiB/s)
reading overlays/i2c1.dtbo
226 bytes read in 6 ms (36.1 KiB/s)
reading overlays/uart0.dtbo
227 bytes read in 6 ms (36.1 KiB/s)
Kernel image @ 0x40008000 [ 0x000000 - 0x6cf8a8 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8838804 Bytes = 8.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 44000000
   Booting using the fdt blob at 0x44000000
   reserving fdt memory region: addr=44000000 size=2c000
   Using Device Tree in place at 44000000, end 4402efff

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 6.1.75+ (mdrjr@powah) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #20 SMP PREEMPT Wed Feb  7 15:22:29 -03 2024
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel ODROID XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0x00000000b6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000040000000-0x000000006fffffff]
[    0.000000]   HighMem  [mem 0x0000000070000000-0x00000000be9fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Running under secure firmware.
[    0.000000] percpu: Embedded 17 pages/cpu s39124 r8192 d22316 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false
[    0.000000] hdmi: using HDMI mode
[    0.000000] Unknown kernel command line parameters "false HPD=true vout=hdmi", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1895044K/2074624K available (12288K kernel code, 1125K rwdata, 2884K rodata, 2048K init, 365K bss, 48508K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000031] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57
[    0.001524] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.001547] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.001569] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001585] Ignoring duplicate/late registration of read_current_timer delay
[    0.002378] Console: colour dummy device 80x30
[    0.003131] printk: console [tty1] enabled
[    0.003197] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003247] CPU: Testing write buffer coherency: ok
[    0.003337] pid_max: default: 32768 minimum: 301
[    0.003488] LSM: Security Framework initializing
[    0.003683] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003737] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005485] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.006904] cblist_init_generic: Setting adjustable number of callback queues.
[    0.006952] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007146] cblist_init_generic: Setting adjustable number of callback queues.
[    0.007181] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007389] Setting up static identity map for 0x40200000 - 0x40200060
[    0.007737] ARM CCI driver probed
[    0.008327] Exynos MCPM support installed
[    0.008731] rcu: Hierarchical SRCU implementation.
[    0.008758] rcu: 	Max phase no-delay instances is 1000.
[    0.010042] smp: Bringing up secondary CPUs ...
[    0.011196] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.012498] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.013731] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.014929] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.014946] CPU4: detected I-Cache line size mismatch, workaround enabled
[    0.014955] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.015045] CPU4: Spectre BHB: enabling loop workaround for all CPUs
[    0.016316] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.016329] CPU5: detected I-Cache line size mismatch, workaround enabled
[    0.016337] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.017657] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.017671] CPU6: detected I-Cache line size mismatch, workaround enabled
[    0.017678] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.018953] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.018967] CPU7: detected I-Cache line size mismatch, workaround enabled
[    0.018975] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.019209] smp: Brought up 1 node, 8 CPUs
[    0.019273] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.019304] CPU: All CPU(s) started in HYP mode.
[    0.019326] CPU: Virtualization extensions available.
[    0.020784] devtmpfs: initialized
[    0.042185] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.042467] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.042509] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.045683] pinctrl core: initialized pinctrl subsystem
[    0.048594] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.052284] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.054019] audit: initializing netlink subsys (disabled)
[    0.054298] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1
[    0.054879] thermal_sys: Registered thermal governor 'step_wise'
[    0.055154] cpuidle: using governor menu
[    0.055626] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.055656] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.185971] EXYNOS5420 PMU initialized
[    0.303866] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.305789] fbcon: Taking over console
[    0.307554] iommu: Default domain type: Translated 
[    0.307577] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.307977] usbcore: registered new interface driver usbfs
[    0.308045] usbcore: registered new interface driver hub
[    0.308114] usbcore: registered new device driver usb
[    0.308839] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.308870] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.309236] s3c-i2c 12c70000.i2c: i2c-0: S3C I2C adapter
[    0.309447] s3c-i2c 12c80000.i2c: slave address 0x00
[    0.309475] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[    0.309774] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[    0.310262] mc: Linux media interface: v0.10
[    0.310341] videodev: Linux video capture interface: v2.00
[    0.310959] Advanced Linux Sound Architecture Driver Initialized.
[    0.311999] clocksource: Switched to clocksource mct-frc
[    0.312475] VFS: Disk quotas dquot_6.6.0
[    0.312552] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.325833] NET: Registered PF_INET protocol family
[    0.326098] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.327948] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.327999] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.328033] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.328187] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.328492] TCP: Hash tables configured (established 8192 bind 8192)
[    0.328614] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.328675] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.328929] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.328992] NET: Registered PF_XDP protocol family
[    0.329531] Trying to unpack rootfs image as initramfs...
[    0.342227] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.343417] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.345522] Initialise system trusted keyrings
[    0.345899] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.355361] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.443685] NET: Registered PF_ALG protocol family
[    0.443722] Key type asymmetric registered
[    0.443743] Asymmetric key parser 'x509' registered
[    0.443967] bounce: pool size: 64 pages
[    0.444134] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.444544] io scheduler mq-deadline registered
[    0.444572] io scheduler kyber registered
[    0.444821] io scheduler bfq registered
[    0.446665] samsung-pinctrl 13400000.pinctrl: Failed to create device link (0x180) with soc
[    0.449003] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator
[    0.450014] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator
[    0.450191] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator
[    0.450626] exynos5_usb3drd_phy 12500000.phy: supply vbus not found, using dummy regulator
[    0.450796] exynos5_usb3drd_phy 12500000.phy: supply vbus-boost not found, using dummy regulator
[    0.459215] dma-pl330 3880000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.459253] dma-pl330 3880000.dma-controller: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.462533] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.462567] dma-pl330 121a0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.465775] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.465809] dma-pl330 121b0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.467084] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.467117] dma-pl330 10800000.dma-controller: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.482056] dma-pl330 3880000.dma-controller: PM domain MAU will not be powered off
[    0.558410] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.561085] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 124, base_baud = 0) is a S3C6400/10
[    0.561647] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 125, base_baud = 0) is a S3C6400/10
[    1.585427] printk: console [ttySAC2] enabled
[    1.592161] exynos-trng 10830600.rng: Exynos True Random Number Generator.
[    1.599288] exynos-mixer 14450000.mixer: Adding to iommu group 0
[    1.606847] exynos-drm-g2d 10850000.g2d: Adding to iommu group 1
[    1.613291] exynos-rotator 11c00000.rotator: Adding to iommu group 2
[    1.619431] exynos-scaler 12800000.scaler: Adding to iommu group 3
[    1.626047] exynos-scaler 12810000.scaler: Adding to iommu group 4
[    1.632436] exynos-scaler 12820000.scaler: Adding to iommu group 5
[    1.639140] exynos-drm-gsc 13e00000.video-scaler: Adding to iommu group 6
[    1.645303] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered successfully.
[    1.652501] exynos-drm-gsc 13e10000.video-scaler: Adding to iommu group 7
[    1.659584] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered successfully.
[    1.684171] brd: module loaded
[    1.686959] usbcore: registered new device driver r8152-cfgselector
[    1.692100] usbcore: registered new interface driver r8152
[    1.697514] usbcore: registered new interface driver ax88179_178a
[    1.703594] usbcore: registered new interface driver cdc_ether
[    1.709369] usbcore: registered new interface driver cdc_subset
[    1.715319] usbcore: registered new interface driver r8153_ecm
[    1.724062] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.729566] exynos-ehci 12110000.usb: EHCI Host Controller
[    1.735068] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    1.743236] exynos-ehci 12110000.usb: irq 133, io mem 0x12110000
[    1.772062] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    1.776832] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.784881] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.792064] usb usb1: Product: EHCI Host Controller
[    1.796879] usb usb1: Manufacturer: Linux 6.1.75+ ehci_hcd
[    1.802367] usb usb1: SerialNumber: 12110000.usb
[    1.807723] hub 1-0:1.0: USB hub found
[    1.810696] hub 1-0:1.0: 3 ports detected
[    1.816107] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.821609] exynos-ohci 12120000.usb: USB Host Controller
[    1.827051] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    1.834944] exynos-ohci 12120000.usb: irq 133, io mem 0x12120000
[    1.906297] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    1.913155] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.920296] usb usb2: Product: USB Host Controller
[    1.925088] usb usb2: Manufacturer: Linux 6.1.75+ ohci_hcd
[    1.930518] usb usb2: SerialNumber: 12120000.usb
[    1.935842] hub 2-0:1.0: USB hub found
[    1.938876] hub 2-0:1.0: 3 ports detected
[    1.945493] mousedev: PS/2 mouse device common for all mice
[    1.951361] i2c_dev: i2c /dev entries driver
[    1.978928] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    1.996080] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[    2.015442] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.084693] s5m-rtc s2mps14-rtc: registered as rtc0
[    2.089969] s5m-rtc s2mps14-rtc: setting system clock to 2024-02-07T18:31:54 UTC (1707330714)
[    2.097417] s2mps11-clk s2mps11-clk: DMA mask not set
[    2.112430] exynos-tmu 10060000.tmu: More trip points than supported by this TMU.
[    2.118454] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode.
[    2.128377] exynos-tmu 10064000.tmu: More trip points than supported by this TMU.
[    2.134434] exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode.
[    2.144382] exynos-tmu 10068000.tmu: More trip points than supported by this TMU.
[    2.150400] exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode.
[    2.160411] exynos-tmu 1006c000.tmu: More trip points than supported by this TMU.
[    2.166484] exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode.
[    2.176375] exynos-tmu 100a0000.tmu: More trip points than supported by this TMU.
[    2.182430] exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode.
[    2.191774] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    2.199498] device-mapper: uevent: version 1.0.3
[    2.203704] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    2.227306] sdhci: Secure Digital Host Controller Interface driver
[    2.232062] sdhci: Copyright(c) Pierre Ossman
[    2.236773] Synopsys Designware Multimedia Card Interface Driver
[    2.243886] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    2.244231] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    2.256103] s5p-secss 10830000.sss: s5p-sss driver registered
[    2.257765] hid: raw HID events driver (C) Jiri Kosina
[    2.262028] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    2.273428] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    2.273782] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    2.279114] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 144,64 bit host data width,64 deep fifo
[    2.285198] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    2.299948] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 145,64 bit host data width,64 deep fifo
[    2.309717] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    2.313041] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.329971] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    2.335309] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    2.336562] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.342975] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    2.357992] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    2.364999] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0-0)
[    2.372516] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0-1)
[    2.380291] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1-0)
[    2.388197] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1-1)
[    2.395695] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
[    2.407644] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_0 not found
[    2.414123] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_1 not found
[    2.422234] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0
[    2.435265] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s
[    2.444132] NET: Registered PF_PACKET protocol family
[    2.447719] NET: Registered PF_KEY protocol family
[    2.452997] Key type dns_resolver registered
[    2.457216] Registering SWP/SWPB emulation handler
[    2.461905] registered taskstats version 1
[    2.465615] Loading compiled-in X.509 certificates
[    2.470840] Key type .fscrypt registered
[    2.474303] Key type fscrypt-provisioning registered
[    2.514073] mmc0: new ultra high speed SDR104 SDXC card at address 0001
[    2.520488] mmcblk0: mmc0:0001 SD64G 58.2 GiB 
[    2.527018]  mmcblk0: p1 p2
[    2.752335] usb 2-1: new full-speed USB device number 2 using exynos-ohci
[    3.028389] usb 2-1: New USB device found, idVendor=046a, idProduct=010e, bcdDevice= 0.13
[    3.035435] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    3.042451] usb 2-1: Product: USB Wireless Device
[    3.086276] Freeing initrd memory: 8632K
[    3.141690] Key type encrypted registered
[    3.206924] exynos-chipid 10000000.chipid: cpu0 opp0, freq: 1500 missing
[    3.212298] exynos-chipid 10000000.chipid: cpu4 opp0, freq: 2100 missing
[    3.218893] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5800] PRO_ID[0xe5422000] REV[0x1] Detected
[    3.232890] OF: graph: no port node found in /soc/hdmi@14530000
[    3.239779] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[    3.246217] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0e7bc8c)
[    3.252778] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc0e7c26c)
[    3.259518] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully registered.
[    3.267775] exynos-drm exynos-drm: bound 10850000.g2d (ops 0xc0e7d27c)
[    3.274117] exynos-rotator 11c00000.rotator: The exynos rotator has been probed successfully
[    3.282521] exynos-drm exynos-drm: bound 11c00000.rotator (ops 0xc0e7db08)
[    3.289334] exynos-scaler 12800000.scaler: The exynos scaler has been probed successfully
[    3.297502] exynos-drm exynos-drm: bound 12800000.scaler (ops 0xc0e7e250)
[    3.304266] exynos-scaler 12810000.scaler: The exynos scaler has been probed successfully
[    3.312424] exynos-drm exynos-drm: bound 12810000.scaler (ops 0xc0e7e250)
[    3.319166] exynos-scaler 12820000.scaler: The exynos scaler has been probed successfully
[    3.327357] exynos-drm exynos-drm: bound 12820000.scaler (ops 0xc0e7e250)
[    3.334108] exynos-drm-gsc 13e00000.video-scaler: The exynos gscaler has been probed successfully
[    3.342961] exynos-drm exynos-drm: bound 13e00000.video-scaler (ops 0xc0e7eb24)
[    3.350180] exynos-drm-gsc 13e10000.video-scaler: The exynos gscaler has been probed successfully
[    3.359059] exynos-drm exynos-drm: bound 13e10000.video-scaler (ops 0xc0e7eb24)
[    3.539347] Console: switching to colour frame buffer device 240x75
[    3.601777] exynos-drm exynos-drm: [drm] fb0: exynosdrmfb frame buffer device
[    3.610920] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 0
[    3.621589] mali 11800000.gpu: GPU identified as 0x0620 r0p1 status 0
[    3.626907] mali 11800000.gpu: Protected mode not available
[    3.634738] mali 11800000.gpu: Probed as mali0
[    3.644283] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.648455] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[    3.657774] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.665845] xhci-hcd xhci-hcd.8.auto: irq 153, io mem 0x12000000
[    3.671911] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.677228] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[    3.684848] xhci-hcd xhci-hcd.8.auto: Host supports USB 3.0 SuperSpeed
[    3.691448] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.699578] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.706769] usb usb3: Product: xHCI Host Controller
[    3.711580] usb usb3: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.717083] usb usb3: SerialNumber: xhci-hcd.8.auto
[    3.722491] hub 3-0:1.0: USB hub found
[    3.725618] hub 3-0:1.0: 1 port detected
[    3.729949] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.737737] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.745850] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.753096] usb usb4: Product: xHCI Host Controller
[    3.757852] usb usb4: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.763340] usb usb4: SerialNumber: xhci-hcd.8.auto
[    3.768592] hub 4-0:1.0: USB hub found
[    3.771885] hub 4-0:1.0: 1 port detected
[    3.778661] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.782735] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    3.790808] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.799842] xhci-hcd xhci-hcd.9.auto: irq 154, io mem 0x12400000
[    3.805898] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.811153] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 6
[    3.818802] xhci-hcd xhci-hcd.9.auto: Host supports USB 3.0 SuperSpeed
[    3.825433] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.833539] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.840704] usb usb5: Product: xHCI Host Controller
[    3.845563] usb usb5: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.851006] usb usb5: SerialNumber: xhci-hcd.9.auto
[    3.856294] hub 5-0:1.0: USB hub found
[    3.859570] hub 5-0:1.0: 1 port detected
[    3.863863] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.871624] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.879790] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.887065] usb usb6: Product: xHCI Host Controller
[    3.894035] usb usb6: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.900200] usb usb6: SerialNumber: xhci-hcd.9.auto
[    3.906175] hub 6-0:1.0: USB hub found
[    3.910542] hub 6-0:1.0: 1 port detected
[    3.917059] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[    3.923690] s3c-rtc 101e0000.rtc: registered as rtc1
[    3.937416] exynos-bus: new bus device registered: soc:bus-wcore ( 88700 KHz ~ 532000 KHz)
[    3.947531] exynos-bus: new bus device registered: soc:bus-noc ( 66600 KHz ~ 111000 KHz)
[    3.957616] exynos-bus: new bus device registered: soc:bus-fsys-apb (111000 KHz ~ 222000 KHz)
[    3.968237] exynos-bus: new bus device registered: soc:bus-fsys2 ( 75000 KHz ~ 200000 KHz)
[    3.978866] exynos-bus: new bus device registered: soc:bus-mfc ( 83250 KHz ~ 333000 KHz)
[    3.989172] exynos-bus: new bus device registered: soc:bus-gen ( 88700 KHz ~ 266000 KHz)
[    3.999145] exynos-bus: new bus device registered: soc:bus-peri ( 66600 KHz ~  66600 KHz)
[    4.010383] exynos-bus: new bus device registered: soc:bus-g2d ( 83250 KHz ~ 333000 KHz)
[    4.012119] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    4.023755] exynos-bus: new bus device registered: soc:bus-g2d-acp ( 66500 KHz ~ 266000 KHz)
[    4.038918] exynos-bus: new bus device registered: soc:bus-jpeg ( 75000 KHz ~ 300000 KHz)
[    4.048241] exynos-bus: new bus device registered: soc:bus-jpeg-apb ( 83250 KHz ~ 166500 KHz)
[    4.057710] exynos-bus: new bus device registered: soc:bus-disp1-fimd (120000 KHz ~ 200000 KHz)
[    4.067398] exynos-bus: new bus device registered: soc:bus-disp1 (120000 KHz ~ 300000 KHz)
[    4.076626] exynos-bus: new bus device registered: soc:bus-gscl-scaler (150000 KHz ~ 300000 KHz)
[    4.086563] exynos-bus: new bus device registered: soc:bus-mscl ( 84000 KHz ~ 666000 KHz)
[    4.144929] ALSA device list:
[    4.149296]   #0: ODROID-XU4
[    4.156697] Freeing unused kernel image (initmem) memory: 2048K
[    4.203349] Run /init as init process
[    4.217791] usb 3-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=92.22
[    4.227049] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.235172] usb 3-1: Product: USB2.0 Hub
[    4.239709] usb 3-1: Manufacturer: GenesysLogic
Loading, please wait...
[    4.300108] hub 3-1:1.0: USB hub found
[    4.306827] hub 3-1:1.0: 2 ports detected
Starting version 249.11-0ubuntu3.12
[    4.382452] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[    4.415084] usb 4-1: New USB device found, idVendor=05e3, idProduct=0616, bcdDevice=92.22
[    4.423727] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.431249] usb 4-1: Product: USB3.0 Hub
[    4.435575] usb 4-1: Manufacturer: GenesysLogic
[    4.460098] hub 4-1:1.0: USB hub found
[    4.464757] hub 4-1:1.0: 2 ports detected
[    4.972155] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd
[    5.003126] usb 6-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00
[    5.011725] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    5.019315] usb 6-1: Product: USB 10/100/1000 LAN
[    5.024496] usb 6-1: Manufacturer: Realtek
[    5.028933] usb 6-1: SerialNumber: 000001000000
[    5.266153] r8152-cfgselector 6-1: reset SuperSpeed USB device number 2 using xhci-hcd
[    5.348708] r8152 6-1:1.0: load rtl8153a-3 v2 02/07/20 successfully
[    5.432795] r8152 6-1:1.0 eth0: v1.12.13
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.37.2
[/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p2] fsck.ext4 -y -C0 /dev/mmcblk0p2 
e2fsck 1.46.5 (30-Dec-2021)
rootfs: clean, 50289/3809280 files, 778797/15234560 blocks
done.
[    5.923537] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    6.488158] systemd[1]: systemd 249.11-0ubuntu3.12 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    6.526344] systemd[1]: Detected architecture arm.

Welcome to [1B][1mUbuntu 22.04.3 LTS[1B][0m!

[    6.564561] systemd[1]: Hostname set to <odroid>.
[    8.102200] random: crng init done
[    8.105360] systemd[1]: Queued start job for default target Graphical Interface.
[    8.190661] systemd[1]: Created slice Slice /system/modprobe.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/modprobe[1B][0m.
[    8.235779] systemd[1]: Created slice Slice /system/serial-getty.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/serial-getty[1B][0m.
[    8.278279] systemd[1]: Created slice Slice /system/systemd-fsck.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/systemd-fsck[1B][0m.
[    8.328374] systemd[1]: Created slice User and Session Slice.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mUser and Session Slice[1B][0m.
[    8.374254] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDispatch Password …ts to Console Directory Watch[1B][0m.
[    8.424257] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mForward Password R…uests to Wall Directory Watch[1B][0m.
[    8.474504] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[[1B][0;32m  OK  [1B][0m] Set up automount [1B][0;1;39mArbitrary…s File System Automount Point[1B][0m.
[    8.523733] systemd[1]: Reached target Local Encrypted Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Encrypted Volumes[1B][0m.
[    8.573422] systemd[1]: Reached target Path Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPath Units[1B][0m.
[    8.612746] systemd[1]: Reached target Remote File Systems.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mRemote File Systems[1B][0m.
[    8.652147] systemd[1]: Reached target Slice Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSlice Units[1B][0m.
[    8.693032] systemd[1]: Reached target Swaps.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSwaps[1B][0m.
[    8.732213] systemd[1]: Reached target Local Verity Protected Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Verity Protected Volumes[1B][0m.
[    8.774339] systemd[1]: Listening on Syslog Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mSyslog Socket[1B][0m.
[    8.815157] systemd[1]: Listening on fsck to fsckd communication Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mfsck to fsckd communication Socket[1B][0m.
[    8.864271] systemd[1]: Listening on initctl Compatibility Named Pipe.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39minitctl Compatibility Named Pipe[1B][0m.
[    8.914443] systemd[1]: Listening on Journal Audit Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Audit Socket[1B][0m.
[    8.954241] systemd[1]: Listening on Journal Socket (/dev/log).
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket (/dev/log)[1B][0m.
[    9.005782] systemd[1]: Listening on Journal Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket[1B][0m.
[    9.057141] systemd[1]: Listening on udev Control Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Control Socket[1B][0m.
[    9.105159] systemd[1]: Listening on udev Kernel Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Kernel Socket[1B][0m.
[    9.153069] systemd[1]: Reached target Socket Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSocket Units[1B][0m.
[    9.192522] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[    9.253775] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting [1B][0;1;39mPOSIX Message Queue File System[1B][0m...
[    9.318423] systemd[1]: Mounting Kernel Debug File System...
         Mounting [1B][0;1;39mKernel Debug File System[1B][0m...
[    9.369546] systemd[1]: Mounting Kernel Trace File System...
         Mounting [1B][0;1;39mKernel Trace File System[1B][0m...
[    9.447322] systemd[1]: Starting Journal Service...
         Starting [1B][0;1;39mJournal Service[1B][0m...
[    9.499171] systemd[1]: Starting Set the console keyboard layout...
         Starting [1B][0;1;39mSet the console keyboard layout[1B][0m...
[    9.552554] systemd[1]: Condition check resulted in Create List of Static Device Nodes being skipped.
[    9.613263] systemd[1]: Starting Load Kernel Module configfs...
         Starting [1B][0;1;39mLoad Kernel Module configfs[1B][0m...
[    9.686870] systemd[1]: Starting Load Kernel Module drm...
         Starting [1B][0;1;39mLoad Kernel Module drm[1B][0m...
[    9.732828] systemd[1]: Starting Load Kernel Module efi_pstore...
         Starting [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m...
[    9.785994] systemd[1]: Starting Load Kernel Module fuse...
         Starting [1B][0;1;39mLoad Kernel Module fuse[1B][0m...
[    9.834588] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[    9.862434] systemd[1]: Starting Load Kernel Modules...
         Starting [1B][0;1;39mLoad Kernel Modules[1B][0m...
[    9.909195] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m...
[    9.969419] systemd[1]: Starting Coldplug All udev Devices...
         Starting [1B][0;1;39mCol[    9.978073] EXT4-fs (mmcblk0p2): re-mounted. Quota mode: none.
dplug All udev Devices[1B][0m...
[   10.033588] systemd[1]: Started Journal Service.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mJournal Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mPOSIX Message Queue File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Debug File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Trace File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet the console keyboard layout[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module configfs[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module drm[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module fuse[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Modules[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m.
         Mounting [1B][0;1;39mKernel Configuration File System[1B][0m...
         Starting [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m...
[   10.718007] systemd-journald[251]: Received client request to flush runtime journal.
         Starting [1B][0;1;39mLoad/Save Random Seed[1B][0m...
         Starting [1B][0;1;39mApply Kernel Variables[1B][0m...
         Starting [1B][0;1;39mCreate System Users[1B][0m...
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Configuration File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad/Save Random Seed[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mColdplug All udev Devices[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mApply Kernel Variables[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate System Users[1B][0m.
         Starting [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPreparation for Local File Systems[1B][0m.
         Starting [1B][0;1;39mRule-based Manage…for Device Events and Files[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mRule-based Manager for Device Events and Files[1B][0m.
[[1B][0;32m  OK  [1B][0m] Found device [1B][0;1;39m/dev/ttySAC2[1B][0m.
[[1B][0;32m  OK  [1B][0m] Found device [1B][0;1;39m/dev/disk/by-label/boot[1B][0m.
         Starting [1B][0;1;39mFile System Check on /dev/disk/by-label/boot[1B][0m...
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSound Card[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mFile System Check Daemon to report status[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mFile System Check on /dev/disk/by-label/boot[1B][0m.
         Mounting [1B][0;1;39m/media/boot[1B][0m...
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39m/media/boot[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal File Systems[1B][0m.
         Starting [1B][0;1;39mSet console font and keymap[1B][0m...
         Starting [1B][0;1;39mSet Up Additional Binary Formats[1B][0m...
         Starting [1B][0;1;39mCreate Volatile Files and Directories[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console font and keymap[1B][0m.
         Mounting [1B][0;1;39mArbitrary Executable File Formats File System[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate Volatile Files and Directories[1B][0m.
[[1B][0;1;31mFAILED[1B][0m] Failed to mount [1B][0;1;39mArbitrary …able File Formats File System[1B][0m.
See 'systemctl status proc-sys-fs-binfmt_misc.mount' for details.
         Starting [1B][0;1;39mNetwork Name Resolution[1B][0m...
         Starting [1B][0;1;39mNetwork Time Synchronization[1B][0m...
         Starting [1B][0;1;39mRecord System Boot/Shutdown in UTMP[1B][0m...
[[1B][0;1;31mFAILED[1B][0m] Failed to start [1B][0;1;39mSet Up Additional Binary Formats[1B][0m.
See 'systemctl status systemd-binfmt.service' for details.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRecord System Boot/Shutdown in UTMP[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Time Synchronization[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Initialization[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily Cleanup of Temporary Directories[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mBasic System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Time Set[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily apt download activities[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily apt upgrade and clean activities[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily dpkg database backup timer[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDiscard unused blocks once a week[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily rotation of log files[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily man-db regeneration[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mMessage of the Day[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mTimer Units[1B][0m.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mD-Bus System Message Bus Socket[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mRegular background program processing daemon[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mD-Bus System Message Bus[1B][0m.
         Starting [1B][0;1;39mNetwork Manager[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSave initial kernel messages after boot[1B][0m.
         Starting [1B][0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[1B][0m...
         Starting [1B][0;1;39mLSB: Load kernel …d to enable cpufreq scaling[1B][0m...
         Starting [1B][0;1;39mAuthorization Manager[1B][0m...
         Starting [1B][0;1;39mLSB: Run /etc/rc.local if it exist[1B][0m...
         Starting [1B][0;1;39mSystem Logging Service[1B][0m...
         Starting [1B][0;1;39mUser Login Management[1B][0m...
         Starting [1B][0;1;39mWPA supplicant[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Name Resolution[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSystem Logging Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mWPA supplicant[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: Run /etc/rc.local if it exist[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mUser Login Management[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: Load kernel m…ded to enable cpufreq scaling[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mAuthorization Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mNetwork[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mHost and Network Name Lookups[1B][0m.
         Starting [1B][0;1;39mModem Manager[1B][0m...
         Starting [1B][0;1;39mLSB: set CPUFreq kernel parameters[1B][0m...
         Starting [1B][0;1;39mODROID Specific System Tweaks[1B][0m...
         Starting [1B][0;1;39m/etc/rc.local Compatibility[1B][0m...
         Starting [1B][0;1;39mOpenBSD Secure Shell server[1B][0m...
         Starting [1B][0;1;39mHostname Service[1B][0m...
         Starting [1B][0;1;39mPermit User Sessions[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mODROID Specific System Tweaks[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39m/etc/rc.local Compatibility[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mPermit User Sessions[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mModem Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mOpenBSD Secure Shell server[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mHostname Service[1B][0m.
         Starting [1B][0;1;39mNetwork Manager Script Dispatcher Service[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSerial Getty on ttySAC2[1B][0m.
         Starting [1B][0;1;39mSet console scheme[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console scheme[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: set CPUFreq kernel parameters[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Manager Script Dispatcher Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/getty[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mGetty on tty1[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLogin Prompts[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mMulti-User System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mGraphical Interface[1B][0m.
         Starting [1B][0;1;39mRecord Runlevel Change in UTMP[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRecord Runlevel Change in UTMP[1B][0m.


Ubuntu 22.04.3 LTS odroid ttySAC2

odroid login: 

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

no no. Everything is fine now. It took some time to slow down the fan.

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

Okay! that's good to know, can you try one last time ? I've just uploaded a new zImage that should be more smart.
I will wait your OK, to push this update.

Once I push, you will be able to update as usual..

Btw, sorry to keep asking for testing I don't have a board that shows the same symptons as yours...
These users thanked the author mdrjr for the post:
odroid (Thu Feb 08, 2024 9:17 am)

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Yes. This one works too.

Now I have a problem, with the USB devices. A USB Card Reader is recognized but I can´t get a device (/dev/sda?) for it.

Should I create a new ticket?

Here is the output

Code: Select all

U-Boot 2017.05-00008-g6a9ddb8303-dirty (May 19 2020 - 19:48:01 +0900) for ODROID-XU4

CPU:   Exynos5422 @ 800 MHz
Model: Odroid XU4 based on EXYNOS5422
Board: Odroid XU4 based on EXYNOS5422
Type:  xu4
DRAM:  2 GiB
MMC:   EXYNOS DWMMC: 0, EXYNOS DWMMC: 1
MMC Device 0 ( SD ): 58.2 GiB
mmc_init: -5, time 4
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Press quickly 'Enter' twice to stop autoboot:  0 
reading /boot.ini
2365 bytes read in 4 ms (577.1 KiB/s)
## Executing script at 43e00000
reading config.ini
6911 bytes read in 5 ms (1.3 MiB/s)
ini: Imported macaddr as 00:1e:06:61:7a:39
ini: Imported vout as hdmi
ini: Imported HPD as true
ini: Imported cecenable as false
ini: Imported disable_vu7 as false
ini: Imported ddr_freq as 825
ini: Imported overlay_resize as 16384
ini: Imported overlay_profile as 
ini: Imported overlays as spi0 i2c0 i2c1 uart0
No FDT memory address configured. Please configure
the FDT address via "fdt addr <address>" command.
Aborting!
reading zImage
7141656 bytes read in 480 ms (14.2 MiB/s)
reading uInitrd
8838868 bytes read in 590 ms (14.3 MiB/s)
reading exynos5422-odroidxu4.dtb
88559 bytes read in 12 ms (7 MiB/s)
reading overlays/spi0.dtbo
691 bytes read in 6 ms (112.3 KiB/s)
reading overlays/i2c0.dtbo
224 bytes read in 6 ms (36.1 KiB/s)
reading overlays/i2c1.dtbo
226 bytes read in 5 ms (43.9 KiB/s)
reading overlays/uart0.dtbo
227 bytes read in 6 ms (36.1 KiB/s)
Kernel image @ 0x40008000 [ 0x000000 - 0x6cf918 ]
## Loading init Ramdisk from Legacy Image at 42000000 ...
   Image Name:   uInitrd
   Image Type:   ARM Linux RAMDisk Image (uncompressed)
   Data Size:    8838804 Bytes = 8.4 MiB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
## Flattened Device Tree blob at 44000000
   Booting using the fdt blob at 0x44000000
   reserving fdt memory region: addr=44000000 size=2c000
   Using Device Tree in place at 44000000, end 4402efff

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x100
[    0.000000] Linux version 6.1.75+ (mdrjr@powah) (arm-linux-gnueabihf-gcc (Ubuntu 11.4.0-1ubuntu1~22.04) 11.4.0, GNU ld (GNU Binutils for Ubuntu) 2.38) #27 SMP PREEMPT Wed Feb  7 16:54:36 -03 2024
[    0.000000] CPU: ARMv7 Processor [410fc073] revision 3 (ARMv7), cr=30c5387d
[    0.000000] CPU: div instructions available: patching division code
[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[    0.000000] OF: fdt: Machine model: Hardkernel ODROID XU4
[    0.000000] Memory policy: Data cache writealloc
[    0.000000] cma: Reserved 128 MiB at 0x00000000b6800000
[    0.000000] Samsung CPU ID: 0xe5422001
[    0.000000] Zone ranges:
[    0.000000]   Normal   [mem 0x0000000040000000-0x000000006fffffff]
[    0.000000]   HighMem  [mem 0x0000000070000000-0x00000000be9fffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x00000000be9fffff]
[    0.000000] Running under secure firmware.
[    0.000000] percpu: Embedded 17 pages/cpu s39124 r8192 d22316 u69632
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 516928
[    0.000000] Kernel command line: console=tty1 console=ttySAC2,115200n8 root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait ro fsck.repair=yes net.ifnames=0  HPD=true vout=hdmi usbhid.quirks=0x0eef:0x0005:0x0004 smsc95xx.macaddr=00:1e:06:61:7a:39 false
[    0.000000] hdmi: using HDMI mode
[    0.000000] Unknown kernel command line parameters "false HPD=true vout=hdmi", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] Memory: 1895044K/2074624K available (12288K kernel code, 1125K rwdata, 2884K rodata, 2048K init, 365K bss, 48508K reserved, 131072K cma-reserved, 1157120K highmem)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[    0.000000] trace event string verifier disabled
[    0.000000] rcu: Preemptible hierarchical RCU implementation.
[    0.000000] 	Trampoline variant of Tasks RCU enabled.
[    0.000000] 	Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[    0.000000] GIC: Using split EOI/Deactivate mode
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] Switching to timer-based delay loop, resolution 41ns
[    0.000000] clocksource: mct-frc: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.000002] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[    0.000031] genirq: irq_chip COMBINER did not update eff. affinity mask of irq 57
[    0.001527] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.001550] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.001571] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001587] Ignoring duplicate/late registration of read_current_timer delay
[    0.002382] Console: colour dummy device 80x30
[    0.003150] printk: console [tty1] enabled
[    0.003219] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    0.003267] CPU: Testing write buffer coherency: ok
[    0.003359] pid_max: default: 32768 minimum: 301
[    0.003509] LSM: Security Framework initializing
[    0.003705] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.003759] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes, linear)
[    0.005511] CPU0: thread -1, cpu 0, socket 1, mpidr 80000100
[    0.006933] cblist_init_generic: Setting adjustable number of callback queues.
[    0.006980] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007173] cblist_init_generic: Setting adjustable number of callback queues.
[    0.007208] cblist_init_generic: Setting shift to 3 and lim to 1.
[    0.007416] Setting up static identity map for 0x40200000 - 0x40200060
[    0.007760] ARM CCI driver probed
[    0.008354] Exynos MCPM support installed
[    0.008757] rcu: Hierarchical SRCU implementation.
[    0.008784] rcu: 	Max phase no-delay instances is 1000.
[    0.010065] smp: Bringing up secondary CPUs ...
[    0.011215] CPU1: thread -1, cpu 1, socket 1, mpidr 80000101
[    0.012518] CPU2: thread -1, cpu 2, socket 1, mpidr 80000102
[    0.013745] CPU3: thread -1, cpu 3, socket 1, mpidr 80000103
[    0.014945] CPU4: thread -1, cpu 0, socket 0, mpidr 80000000
[    0.014963] CPU4: detected I-Cache line size mismatch, workaround enabled
[    0.014971] CPU4: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.015061] CPU4: Spectre BHB: enabling loop workaround for all CPUs
[    0.016332] CPU5: thread -1, cpu 1, socket 0, mpidr 80000001
[    0.016346] CPU5: detected I-Cache line size mismatch, workaround enabled
[    0.016353] CPU5: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.017673] CPU6: thread -1, cpu 2, socket 0, mpidr 80000002
[    0.017687] CPU6: detected I-Cache line size mismatch, workaround enabled
[    0.017695] CPU6: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.018969] CPU7: thread -1, cpu 3, socket 0, mpidr 80000003
[    0.018984] CPU7: detected I-Cache line size mismatch, workaround enabled
[    0.018991] CPU7: Spectre v2: firmware did not set auxiliary control register IBE bit, system vulnerable
[    0.019227] smp: Brought up 1 node, 8 CPUs
[    0.019291] SMP: Total of 8 processors activated (384.00 BogoMIPS).
[    0.019320] CPU: All CPU(s) started in HYP mode.
[    0.019341] CPU: Virtualization extensions available.
[    0.020794] devtmpfs: initialized
[    0.042167] VFP support v0.3: implementor 41 architecture 4 part 30 variant f rev 0
[    0.042450] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.042491] futex hash table entries: 2048 (order: 5, 131072 bytes, linear)
[    0.045682] pinctrl core: initialized pinctrl subsystem
[    0.048590] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.052277] DMA: preallocated 2048 KiB pool for atomic coherent allocations
[    0.054017] audit: initializing netlink subsys (disabled)
[    0.054296] audit: type=2000 audit(0.050:1): state=initialized audit_enabled=0 res=1
[    0.054876] thermal_sys: Registered thermal governor 'step_wise'
[    0.055150] cpuidle: using governor menu
[    0.055623] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
[    0.055654] hw-breakpoint: maximum watchpoint size is 8 bytes.
[    0.186018] EXYNOS5420 PMU initialized
[    0.292447] kprobes: kprobe jump-optimization is enabled. All kprobes are optimized if possible.
[    0.294396] fbcon: Taking over console
[    0.296169] iommu: Default domain type: Translated 
[    0.296193] iommu: DMA domain TLB invalidation policy: lazy mode 
[    0.296597] usbcore: registered new interface driver usbfs
[    0.296665] usbcore: registered new interface driver hub
[    0.296734] usbcore: registered new device driver usb
[    0.297460] s3c-i2c 12c70000.i2c: slave address 0x00
[    0.297491] s3c-i2c 12c70000.i2c: bus frequency set to 378 KHz
[    0.297854] s3c-i2c 12c70000.i2c: i2c-0: S3C I2C adapter
[    0.298067] s3c-i2c 12c80000.i2c: slave address 0x00
[    0.298095] s3c-i2c 12c80000.i2c: bus frequency set to 65 KHz
[    0.298403] s3c-i2c 12c80000.i2c: i2c-2: S3C I2C adapter
[    0.298893] mc: Linux media interface: v0.10
[    0.298980] videodev: Linux video capture interface: v2.00
[    0.299599] Advanced Linux Sound Architecture Driver Initialized.
[    0.300657] clocksource: Switched to clocksource mct-frc
[    0.301111] VFS: Disk quotas dquot_6.6.0
[    0.301187] VFS: Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.314083] NET: Registered PF_INET protocol family
[    0.314344] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.316175] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
[    0.316225] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.316323] TCP established hash table entries: 8192 (order: 3, 32768 bytes, linear)
[    0.316420] TCP bind hash table entries: 8192 (order: 5, 131072 bytes, linear)
[    0.316722] TCP: Hash tables configured (established 8192 bind 8192)
[    0.316845] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.316906] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.317162] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.317224] NET: Registered PF_XDP protocol family
[    0.317929] Trying to unpack rootfs image as initramfs...
[    0.319143] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
[    0.320302] hw perfevents: enabled with armv7_cortex_a15 PMU driver, 7 counters available
[    0.322418] Initialise system trusted keyrings
[    0.322814] workingset: timestamp_bits=14 max_order=19 bucket_order=5
[    0.332250] romfs: ROMFS MTD (C) 2007 Red Hat, Inc.
[    0.421313] NET: Registered PF_ALG protocol family
[    0.421352] Key type asymmetric registered
[    0.421372] Asymmetric key parser 'x509' registered
[    0.421607] bounce: pool size: 64 pages
[    0.421766] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    0.422182] io scheduler mq-deadline registered
[    0.422211] io scheduler kyber registered
[    0.422470] io scheduler bfq registered
[    0.424299] samsung-pinctrl 13400000.pinctrl: Failed to create device link (0x180) with soc
[    0.426669] samsung-usb2-phy 12130000.phy: supply vbus not found, using dummy regulator
[    0.427675] exynos5_usb3drd_phy 12100000.phy: supply vbus not found, using dummy regulator
[    0.427848] exynos5_usb3drd_phy 12100000.phy: supply vbus-boost not found, using dummy regulator
[    0.428277] exynos5_usb3drd_phy 12500000.phy: supply vbus not found, using dummy regulator
[    0.428457] exynos5_usb3drd_phy 12500000.phy: supply vbus-boost not found, using dummy regulator
[    0.436916] dma-pl330 3880000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.436954] dma-pl330 3880000.dma-controller: 	DBUFF-4x8bytes Num_Chans-6 Num_Peri-16 Num_Events-6
[    0.440157] dma-pl330 121a0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.440192] dma-pl330 121a0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.443480] dma-pl330 121b0000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.443515] dma-pl330 121b0000.dma-controller: 	DBUFF-32x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32
[    0.444759] dma-pl330 10800000.dma-controller: Loaded driver for PL330 DMAC-241330
[    0.444791] dma-pl330 10800000.dma-controller: 	DBUFF-64x8bytes Num_Chans-8 Num_Peri-1 Num_Events-32
[    0.460721] dma-pl330 3880000.dma-controller: PM domain MAU will not be powered off
[    0.535265] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[    0.537965] 12c00000.serial: ttySAC0 at MMIO 0x12c00000 (irq = 124, base_baud = 0) is a S3C6400/10
[    0.538538] 12c20000.serial: ttySAC2 at MMIO 0x12c20000 (irq = 125, base_baud = 0) is a S3C6400/10
[    1.562308] printk: console [ttySAC2] enabled
[    1.569020] exynos-trng 10830600.rng: Exynos True Random Number Generator.
[    1.576211] exynos-mixer 14450000.mixer: Adding to iommu group 0
[    1.583694] exynos-drm-g2d 10850000.g2d: Adding to iommu group 1
[    1.590109] exynos-rotator 11c00000.rotator: Adding to iommu group 2
[    1.596352] exynos-scaler 12800000.scaler: Adding to iommu group 3
[    1.602873] exynos-scaler 12810000.scaler: Adding to iommu group 4
[    1.609339] exynos-scaler 12820000.scaler: Adding to iommu group 5
[    1.616128] exynos-drm-gsc 13e00000.video-scaler: Adding to iommu group 6
[    1.622293] exynos-drm-gsc 13e00000.video-scaler: drm gsc registered successfully.
[    1.629431] exynos-drm-gsc 13e10000.video-scaler: Adding to iommu group 7
[    1.636575] exynos-drm-gsc 13e10000.video-scaler: drm gsc registered successfully.
[    1.661233] brd: module loaded
[    1.664031] usbcore: registered new device driver r8152-cfgselector
[    1.669118] usbcore: registered new interface driver r8152
[    1.674609] usbcore: registered new interface driver ax88179_178a
[    1.680627] usbcore: registered new interface driver cdc_ether
[    1.686484] usbcore: registered new interface driver cdc_subset
[    1.692380] usbcore: registered new interface driver r8153_ecm
[    1.701197] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.706699] exynos-ehci 12110000.usb: EHCI Host Controller
[    1.712204] exynos-ehci 12110000.usb: new USB bus registered, assigned bus number 1
[    1.720381] exynos-ehci 12110000.usb: irq 133, io mem 0x12110000
[    1.750737] exynos-ehci 12110000.usb: USB 2.0 started, EHCI 1.00
[    1.755505] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    1.763564] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.770740] usb usb1: Product: EHCI Host Controller
[    1.775555] usb usb1: Manufacturer: Linux 6.1.75+ ehci_hcd
[    1.781043] usb usb1: SerialNumber: 12110000.usb
[    1.786349] hub 1-0:1.0: USB hub found
[    1.789371] hub 1-0:1.0: 3 ports detected
[    1.794810] phy phy-12130000.phy.6: phy_power_on was called before phy_init
[    1.800312] exynos-ohci 12120000.usb: USB Host Controller
[    1.805733] exynos-ohci 12120000.usb: new USB bus registered, assigned bus number 2
[    1.813658] exynos-ohci 12120000.usb: irq 133, io mem 0x12120000
[    1.884946] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 6.01
[    1.891785] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.898938] usb usb2: Product: USB Host Controller
[    1.903743] usb usb2: Manufacturer: Linux 6.1.75+ ohci_hcd
[    1.909160] usb usb2: SerialNumber: 12120000.usb
[    1.914479] hub 2-0:1.0: USB hub found
[    1.917516] hub 2-0:1.0: 3 ports detected
[    1.924097] mousedev: PS/2 mouse device common for all mice
[    1.929926] i2c_dev: i2c /dev entries driver
[    1.958341] vdd_ldo9: Bringing 3300000uV into 3000000-3000000uV
[    1.975294] vddq_mmc2: Bringing 3300000uV into 2800000-2800000uV
[    1.994327] vdd_sd: Bringing 3300000uV into 2800000-2800000uV
[    2.064155] s5m-rtc s2mps14-rtc: registered as rtc0
[    2.069417] s5m-rtc s2mps14-rtc: setting system clock to 2024-02-08T07:44:05 UTC (1707378245)
[    2.076873] s2mps11-clk s2mps11-clk: DMA mask not set
[    2.091876] exynos-tmu 10060000.tmu: More trip points than supported by this TMU.
[    2.097901] exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode.
[    2.107834] exynos-tmu 10064000.tmu: More trip points than supported by this TMU.
[    2.113892] exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode.
[    2.123853] exynos-tmu 10068000.tmu: More trip points than supported by this TMU.
[    2.129875] exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode.
[    2.139892] exynos-tmu 1006c000.tmu: More trip points than supported by this TMU.
[    2.145968] exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode.
[    2.155899] exynos-tmu 100a0000.tmu: More trip points than supported by this TMU.
[    2.161982] exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode.
[    2.171295] s3c2410-wdt 101d0000.watchdog: watchdog inactive, reset disabled, irq disabled
[    2.178996] device-mapper: uevent: version 1.0.3
[    2.183239] device-mapper: ioctl: 4.47.0-ioctl (2022-07-28) initialised: dm-devel@redhat.com
[    2.206839] sdhci: Secure Digital Host Controller Interface driver
[    2.211628] sdhci: Copyright(c) Pierre Ossman
[    2.216349] Synopsys Designware Multimedia Card Interface Driver
[    2.223551] dwmmc_exynos 12220000.mmc: IDMAC supports 32-bit address mode.
[    2.223644] dwmmc_exynos 12200000.mmc: IDMAC supports 32-bit address mode.
[    2.236020] dwmmc_exynos 12220000.mmc: Using internal DMA controller.
[    2.236954] s5p-secss 10830000.sss: s5p-sss driver registered
[    2.242281] dwmmc_exynos 12220000.mmc: Version ID is 250a
[    2.248320] dwmmc_exynos 12200000.mmc: Using internal DMA controller.
[    2.250308] hid: raw HID events driver (C) Jiri Kosina
[    2.253785] dwmmc_exynos 12220000.mmc: DW MMC controller at irq 144,64 bit host data width,64 deep fifo
[    2.259722] dwmmc_exynos 12200000.mmc: Version ID is 250a
[    2.279627] dwmmc_exynos 12200000.mmc: DW MMC controller at irq 145,64 bit host data width,64 deep fifo
[    2.285296] mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.292431] dwmmc_exynos 12200000.mmc: allocated mmc-pwrseq
[    2.310273] exynos-nocp: new NoC Probe device registered: 10ca1000.nocp
[    2.315618] exynos-nocp: new NoC Probe device registered: 10ca1400.nocp
[    2.320916] mmc_host mmc1: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, actual 396825HZ div = 63)
[    2.323068] exynos-nocp: new NoC Probe device registered: 10ca1800.nocp
[    2.338210] exynos-nocp: new NoC Probe device registered: 10ca1c00.nocp
[    2.345186] exynos-ppmu: new PPMU device registered 10d00000.ppmu (ppmu-event3-dmc0-0)
[    2.352775] exynos-ppmu: new PPMU device registered 10d10000.ppmu (ppmu-event3-dmc0-1)
[    2.360608] exynos-ppmu: new PPMU device registered 10d60000.ppmu (ppmu-event3-dmc1-0)
[    2.368559] exynos-ppmu: new PPMU device registered 10d70000.ppmu (ppmu-event3-dmc1-1)
[    2.378645] mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, actual 200000000HZ div = 0)
[    2.380469] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_0 not found
[    2.395123] exynos5-dmc 10c20000.memory-controller: error -ENXIO: IRQ drex_1 not found
[    2.403172] exynos5-dmc 10c20000.memory-controller: DMC initialized, in irq mode: 0
[    2.415594] samsung-i2s 3830000.i2s-sec: DMA channels sourced from device 3830000.i2s
[    2.423518] NET: Registered PF_PACKET protocol family
[    2.427102] NET: Registered PF_KEY protocol family
[    2.433387] Key type dns_resolver registered
[    2.436742] Registering SWP/SWPB emulation handler
[    2.441575] registered taskstats version 1
[    2.445045] Loading compiled-in X.509 certificates
[    2.450523] Key type .fscrypt registered
[    2.453714] Key type fscrypt-provisioning registered
[    2.492756] mmc0: new ultra high speed SDR104 SDXC card at address 0001
[    2.499078] mmcblk0: mmc0:0001 SD64G 58.2 GiB 
[    2.506106]  mmcblk0: p1 p2
[    2.710940] usb 2-1: new full-speed USB device number 2 using exynos-ohci
[    2.986990] usb 2-1: New USB device found, idVendor=046a, idProduct=010e, bcdDevice= 0.13
[    2.993932] usb 2-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[    3.001001] usb 2-1: Product: USB Wireless Device
[    3.075955] Freeing initrd memory: 8632K
[    3.119867] Key type encrypted registered
[    3.194388] exynos-chipid 10000000.chipid: cpu0 opp0, freq: 1500 missing
[    3.199661] exynos-chipid 10000000.chipid: cpu4 opp0, freq: 2100 missing
[    3.206349] exynos-chipid 10000000.chipid: Exynos: CPU[EXYNOS5800] PRO_ID[0xe5422000] REV[0x1] Detected
[    3.220278] OF: graph: no port node found in /soc/hdmi@14530000
[    3.226791] [drm] Exynos DRM: using 14450000.mixer device for DMA mapping operations
[    3.233282] exynos-drm exynos-drm: bound 14450000.mixer (ops 0xc0e7bc8c)
[    3.239768] exynos-drm exynos-drm: bound 14530000.hdmi (ops 0xc0e7c26c)
[    3.246510] exynos-drm-g2d 10850000.g2d: The Exynos G2D (ver 4.1) successfully registered.
[    3.254594] exynos-drm exynos-drm: bound 10850000.g2d (ops 0xc0e7d27c)
[    3.261105] exynos-rotator 11c00000.rotator: The exynos rotator has been probed successfully
[    3.269475] exynos-drm exynos-drm: bound 11c00000.rotator (ops 0xc0e7db08)
[    3.276369] exynos-scaler 12800000.scaler: The exynos scaler has been probed successfully
[    3.284488] exynos-drm exynos-drm: bound 12800000.scaler (ops 0xc0e7e250)
[    3.291285] exynos-scaler 12810000.scaler: The exynos scaler has been probed successfully
[    3.299394] exynos-drm exynos-drm: bound 12810000.scaler (ops 0xc0e7e250)
[    3.306271] exynos-scaler 12820000.scaler: The exynos scaler has been probed successfully
[    3.314335] exynos-drm exynos-drm: bound 12820000.scaler (ops 0xc0e7e250)
[    3.321139] exynos-drm-gsc 13e00000.video-scaler: The exynos gscaler has been probed successfully
[    3.329900] exynos-drm exynos-drm: bound 13e00000.video-scaler (ops 0xc0e7eb24)
[    3.337235] exynos-drm-gsc 13e10000.video-scaler: The exynos gscaler has been probed successfully
[    3.346068] exynos-drm exynos-drm: bound 13e10000.video-scaler (ops 0xc0e7eb24)
[    3.523574] Console: switching to colour frame buffer device 240x75
[    3.580096] exynos-drm exynos-drm: [drm] fb0: exynosdrmfb frame buffer device
[    3.588621] [drm] Initialized exynos 1.1.0 20180330 for exynos-drm on minor 0
[    3.597466] mali 11800000.gpu: GPU identified as 0x0620 r0p1 status 0
[    3.602617] mali 11800000.gpu: Protected mode not available
[    3.609208] mali 11800000.gpu: Probed as mali0
[    3.617223] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.621338] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 3
[    3.629739] xhci-hcd xhci-hcd.8.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.638443] xhci-hcd xhci-hcd.8.auto: irq 153, io mem 0x12000000
[    3.644609] xhci-hcd xhci-hcd.8.auto: xHCI Host Controller
[    3.649747] xhci-hcd xhci-hcd.8.auto: new USB bus registered, assigned bus number 4
[    3.657404] xhci-hcd xhci-hcd.8.auto: Host supports USB 3.0 SuperSpeed
[    3.664090] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.672141] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.679303] usb usb3: Product: xHCI Host Controller
[    3.684123] usb usb3: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.689565] usb usb3: SerialNumber: xhci-hcd.8.auto
[    3.695241] hub 3-0:1.0: USB hub found
[    3.698143] hub 3-0:1.0: 1 port detected
[    3.702423] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.710219] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.718380] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.725565] usb usb4: Product: xHCI Host Controller
[    3.730375] usb usb4: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.735924] usb usb4: SerialNumber: xhci-hcd.8.auto
[    3.741671] hub 4-0:1.0: USB hub found
[    3.744411] hub 4-0:1.0: 1 port detected
[    3.751343] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.755396] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 5
[    3.763535] xhci-hcd xhci-hcd.9.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x0000000002010010
[    3.772593] xhci-hcd xhci-hcd.9.auto: irq 154, io mem 0x12400000
[    3.778556] xhci-hcd xhci-hcd.9.auto: xHCI Host Controller
[    3.783870] xhci-hcd xhci-hcd.9.auto: new USB bus registered, assigned bus number 6
[    3.791504] xhci-hcd xhci-hcd.9.auto: Host supports USB 3.0 SuperSpeed
[    3.798096] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 6.01
[    3.806231] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.813418] usb usb5: Product: xHCI Host Controller
[    3.818226] usb usb5: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.823715] usb usb5: SerialNumber: xhci-hcd.9.auto
[    3.829501] hub 5-0:1.0: USB hub found
[    3.832290] hub 5-0:1.0: 1 port detected
[    3.836506] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    3.844386] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 6.01
[    3.852562] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    3.859674] usb usb6: Product: xHCI Host Controller
[    3.866745] usb usb6: Manufacturer: Linux 6.1.75+ xhci-hcd
[    3.872948] usb usb6: SerialNumber: xhci-hcd.9.auto
[    3.879443] hub 6-0:1.0: USB hub found
[    3.883943] hub 6-0:1.0: 1 port detected
[    3.889841] s3c-rtc 101e0000.rtc: rtc disabled, re-enabling
[    3.896440] s3c-rtc 101e0000.rtc: registered as rtc1
[    3.903899] exynos-bus: new bus device registered: soc:bus-wcore ( 88700 KHz ~ 532000 KHz)
[    3.913573] exynos-bus: new bus device registered: soc:bus-noc ( 66600 KHz ~ 111000 KHz)
[    3.922878] exynos-bus: new bus device registered: soc:bus-fsys-apb (111000 KHz ~ 222000 KHz)
[    3.932653] exynos-bus: new bus device registered: soc:bus-fsys2 ( 75000 KHz ~ 200000 KHz)
[    3.942404] exynos-bus: new bus device registered: soc:bus-mfc ( 83250 KHz ~ 333000 KHz)
[    3.951767] exynos-bus: new bus device registered: soc:bus-gen ( 88700 KHz ~ 266000 KHz)
[    3.960932] exynos-bus: new bus device registered: soc:bus-peri ( 66600 KHz ~  66600 KHz)
[    3.970423] exynos-bus: new bus device registered: soc:bus-g2d ( 83250 KHz ~ 333000 KHz)
[    3.979757] exynos-bus: new bus device registered: soc:bus-g2d-acp ( 66500 KHz ~ 266000 KHz)
[    3.989579] exynos-bus: new bus device registered: soc:bus-jpeg ( 75000 KHz ~ 300000 KHz)
[    3.998873] exynos-bus: new bus device registered: soc:bus-jpeg-apb ( 83250 KHz ~ 166500 KHz)
[    4.007875] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    4.013574] exynos-bus: new bus device registered: soc:bus-disp1-fimd (120000 KHz ~ 200000 KHz)
[    4.024580] exynos-bus: new bus device registered: soc:bus-disp1 (120000 KHz ~ 300000 KHz)
[    4.033833] exynos-bus: new bus device registered: soc:bus-gscl-scaler (150000 KHz ~ 300000 KHz)
[    4.043682] exynos-bus: new bus device registered: soc:bus-mscl ( 84000 KHz ~ 666000 KHz)
[    4.103703] ALSA device list:
[    4.112771]   #0: ODROID-XU4
[    4.118997] Freeing unused kernel image (initmem) memory: 2048K
[    4.151608] Run /init as init process
[    4.205271] usb 3-1: New USB device found, idVendor=05e3, idProduct=0610, bcdDevice=92.22
Loading, please wait...
[    4.215106] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.224370] usb 3-1: Product: USB2.0 Hub
[    4.229784] usb 3-1: Manufacturer: GenesysLogic
[    4.272830] hub 3-1:1.0: USB hub found
[    4.280234] hub 3-1:1.0: 2 ports detected
Starting version 249.11-0ubuntu3.12
[    4.351021] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[    4.384359] usb 4-1: New USB device found, idVendor=05e3, idProduct=0616, bcdDevice=92.22
[    4.393168] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[    4.401036] usb 4-1: Product: USB3.0 Hub
[    4.405452] usb 4-1: Manufacturer: GenesysLogic
[    4.432687] hub 4-1:1.0: USB hub found
[    4.437191] hub 4-1:1.0: 2 ports detected
[    4.970828] usb 6-1: new SuperSpeed USB device number 2 using xhci-hcd
[    5.001614] usb 6-1: New USB device found, idVendor=0bda, idProduct=8153, bcdDevice=30.00
[    5.010269] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[    5.017926] usb 6-1: Product: USB 10/100/1000 LAN
[    5.023159] usb 6-1: Manufacturer: Realtek
[    5.027683] usb 6-1: SerialNumber: 000001000000
[    5.271083] r8152-cfgselector 6-1: reset SuperSpeed USB device number 2 using xhci-hcd
[    5.349791] r8152 6-1:1.0: load rtl8153a-3 v2 02/07/20 successfully
[    5.441248] r8152 6-1:1.0 eth0: v1.12.13
[    5.791627] usb 4-1.1: new SuperSpeed USB device number 3 using xhci-hcd
[    5.847378] usb 4-1.1: New USB device found, idVendor=05e3, idProduct=0749, bcdDevice=15.39
[    5.869460] usb 4-1.1: New USB device strings: Mfr=3, Product=4, SerialNumber=5
[    5.890315] usb 4-1.1: Product: USB3.0 Card Reader
[    5.908679] usb 4-1.1: Manufacturer: Generic
[    5.926544] usb 4-1.1: SerialNumber: 000000001539
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.37.2
[/usr/sbin/fsck.ext4 (1) -- /dev/mmcblk0p2] fsck.ext4 -y -C0 /dev/mmcblk0p2 
e2fsck 1.46.5 (30-Dec-2021)
rootfs: clean, 50305/3809280 files, 783434/15234560 blocks
done.
[    6.280189] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Quota mode: none.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    6.853290] systemd[1]: systemd 249.11-0ubuntu3.12 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    6.888275] systemd[1]: Detected architecture arm.

Welcome to [1B][1mUbuntu 22.04.3 LTS[1B][0m!

[    6.921857] systemd[1]: Hostname set to <odroid>.
[    8.440679] random: crng init done
[    8.447822] systemd[1]: Queued start job for default target Graphical Interface.
[    8.528441] systemd[1]: Created slice Slice /system/modprobe.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/modprobe[1B][0m.
[    8.574622] systemd[1]: Created slice Slice /system/serial-getty.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/serial-getty[1B][0m.
[    8.626701] systemd[1]: Created slice Slice /system/systemd-fsck.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/systemd-fsck[1B][0m.
[    8.673321] systemd[1]: Created slice User and Session Slice.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mUser and Session Slice[1B][0m.
[    8.712970] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDispatch Password …ts to Console Directory Watch[1B][0m.
[    8.762761] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mForward Password R…uests to Wall Directory Watch[1B][0m.
[    8.814092] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[[1B][0;32m  OK  [1B][0m] Set up automount [1B][0;1;39mArbitrary…s File System Automount Point[1B][0m.
[    8.861980] systemd[1]: Reached target Local Encrypted Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Encrypted Volumes[1B][0m.
[    8.912839] systemd[1]: Reached target Path Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPath Units[1B][0m.
[    8.961678] systemd[1]: Reached target Remote File Systems.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mRemote File Systems[1B][0m.
[    9.000822] systemd[1]: Reached target Slice Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSlice Units[1B][0m.
[    9.041547] systemd[1]: Reached target Swaps.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSwaps[1B][0m.
[    9.080860] systemd[1]: Reached target Local Verity Protected Volumes.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal Verity Protected Volumes[1B][0m.
[    9.122946] systemd[1]: Listening on Syslog Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mSyslog Socket[1B][0m.
[    9.162399] systemd[1]: Listening on fsck to fsckd communication Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mfsck to fsckd communication Socket[1B][0m.
[    9.202776] systemd[1]: Listening on initctl Compatibility Named Pipe.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39minitctl Compatibility Named Pipe[1B][0m.
[    9.265444] systemd[1]: Listening on Journal Audit Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Audit Socket[1B][0m.
[    9.323909] systemd[1]: Listening on Journal Socket (/dev/log).
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket (/dev/log)[1B][0m.
[    9.383960] systemd[1]: Listening on Journal Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mJournal Socket[1B][0m.
[    9.446085] systemd[1]: Listening on udev Control Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Control Socket[1B][0m.
[    9.492357] systemd[1]: Listening on udev Kernel Socket.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mudev Kernel Socket[1B][0m.
[    9.531449] systemd[1]: Reached target Socket Units.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSocket Units[1B][0m.
[    9.573680] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[    9.642715] systemd[1]: Mounting POSIX Message Queue File System...
         Mounting [1B][0;1;39mPOSIX Message Queue File System[1B][0m...
[    9.711526] systemd[1]: Mounting Kernel Debug File System...
         Mounting [1B][0;1;39mKernel Debug File System[1B][0m...
[    9.872720] systemd[1]: Mounting Kernel Trace File System...
         Mounting [1B][0;1;39mKernel Trace File System[1B][0m...
[    9.943312] systemd[1]: Starting Journal Service...
         Starting [1B][0;1;39mJournal Service[1B][0m...
[    9.988900] systemd[1]: Starting Set the console keyboard layout...
         Starting [1B][0;1;39mSet the console keyboard layout[1B][0m...
[   10.031129] systemd[1]: Condition check resulted in Create List of Static Device Nodes being skipped.
[   10.059474] systemd[1]: Starting Load Kernel Module configfs...
         Starting [1B][0;1;39mLoad Kernel Module configfs[1B][0m...
[   10.106769] systemd[1]: Starting Load Kernel Module drm...
         Starting [1B][0;1;39mLoad Kernel Module drm[1B][0m...
[   10.144748] systemd[1]: Starting Load Kernel Module efi_pstore...
         Starting [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m...
[   10.194459] systemd[1]: Starting Load Kernel Module fuse...
         Starting [1B][0;1;39mLoad Kernel Module fuse[1B][0m...
[   10.243062] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[   10.264681] systemd[1]: Starting Load Kernel Modules...
         Starting [1B][0;1;39mLoad Kernel Modules[1B][0m...
[   10.305645] systemd[1]: Starting Remount Root and Kernel File Systems...
         Starting [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m...
[   10.367337] systemd[1]: Starting Coldplug All udev Devices...
         Starting [1B][0;1;39mColdplug All udev Devices[1B][0m...
[   10.403201] EXT4-fs (mmcblk0p2): re-mounted. Quota mode: none.
[   10.426537] systemd[1]: Started Journal Service.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mJournal Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mPOSIX Message Queue File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Debug File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Trace File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet the console keyboard layout[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module configfs[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module drm[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module efi_pstore[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Module fuse[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad Kernel Modules[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRemount Root and Kernel File Systems[1B][0m.
         Mounting [1B][0;1;39mKernel Configuration File System[1B][0m...
         Starting [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m...
[   11.106400] systemd-journald[252]: Received client request to flush runtime journal.
         Starting [1B][0;1;39mLoad/Save Random Seed[1B][0m...
         Starting [1B][0;1;39mApply Kernel Variables[1B][0m...
         Starting [1B][0;1;39mCreate System Users[1B][0m...
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39mKernel Configuration File System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mLoad/Save Random Seed[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mApply Kernel Variables[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mColdplug All udev Devices[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mFlush Journal to Persistent Storage[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate System Users[1B][0m.
         Starting [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate Static Device Nodes in /dev[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mPreparation for Local File Systems[1B][0m.
         Starting [1B][0;1;39mRule-based Manage…for Device Events and Files[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mRule-based Manager for Device Events and Files[1B][0m.
[[1B][0;32m  OK  [1B][0m] Found device [1B][0;1;39m/dev/ttySAC2[1B][0m.
[[1B][0;32m  OK  [1B][0m] Found device [1B][0;1;39m/dev/disk/by-label/boot[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSound Card[1B][0m.
         Starting [1B][0;1;39mFile System Check on /dev/disk/by-label/boot[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mFile System Check on /dev/disk/by-label/boot[1B][0m.
         Mounting [1B][0;1;39m/media/boot[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mFile System Check Daemon to report status[1B][0m.
[[1B][0;32m  OK  [1B][0m] Mounted [1B][0;1;39m/media/boot[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLocal File Systems[1B][0m.
         Starting [1B][0;1;39mSet console font and keymap[1B][0m...
         Starting [1B][0;1;39mSet Up Additional Binary Formats[1B][0m...
         Starting [1B][0;1;39mCreate Volatile Files and Directories[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console font and keymap[1B][0m.
         Mounting [1B][0;1;39mArbitrary Executable File Formats File System[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mCreate Volatile Files and Directories[1B][0m.
[[1B][0;1;31mFAILED[1B][0m] Failed to mount [1B][0;1;39mArbitrary …able File Formats File System[1B][0m.
See 'systemctl status proc-sys-fs-binfmt_misc.mount' for details.
         Starting [1B][0;1;39mNetwork Name Resolution[1B][0m...
         Starting [1B][0;1;39mNetwork Time Synchronization[1B][0m...
         Starting [1B][0;1;39mRecord System Boot/Shutdown in UTMP[1B][0m...
[[1B][0;1;31mFAILED[1B][0m] Failed to start [1B][0;1;39mSet Up Additional Binary Formats[1B][0m.
See 'systemctl status systemd-binfmt.service' for details.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRecord System Boot/Shutdown in UTMP[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Time Synchronization[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Initialization[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily Cleanup of Temporary Directories[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mBasic System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mSystem Time Set[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily apt download activities[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily apt upgrade and clean activities[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily dpkg database backup timer[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mPeriodic ext4 Onli…ata Check for All Filesystems[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDiscard unused blocks once a week[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily rotation of log files[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mDaily man-db regeneration[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mMessage of the Day[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mTimer Units[1B][0m.
[[1B][0;32m  OK  [1B][0m] Listening on [1B][0;1;39mD-Bus System Message Bus Socket[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mRegular background program processing daemon[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mD-Bus System Message Bus[1B][0m.
         Starting [1B][0;1;39mNetwork Manager[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSave initial kernel messages after boot[1B][0m.
         Starting [1B][0;1;39mRemove Stale Onli…t4 Metadata Check Snapshots[1B][0m...
         Starting [1B][0;1;39mLSB: Load kernel …d to enable cpufreq scaling[1B][0m...
         Starting [1B][0;1;39mAuthorization Manager[1B][0m...
         Starting [1B][0;1;39mLSB: Run /etc/rc.local if it exist[1B][0m...
         Starting [1B][0;1;39mSystem Logging Service[1B][0m...
         Starting [1B][0;1;39mUser Login Management[1B][0m...
         Starting [1B][0;1;39mWPA supplicant[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Name Resolution[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSystem Logging Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mUser Login Management[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRemove Stale Onli…ext4 Metadata Check Snapshots[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: Run /etc/rc.local if it exist[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mAuthorization Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: Load kernel m…ded to enable cpufreq scaling[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mWPA supplicant[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mNetwork[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mHost and Network Name Lookups[1B][0m.
         Starting [1B][0;1;39mModem Manager[1B][0m...
         Starting [1B][0;1;39mLSB: set CPUFreq kernel parameters[1B][0m...
         Starting [1B][0;1;39mODROID Specific System Tweaks[1B][0m...
         Starting [1B][0;1;39m/etc/rc.local Compatibility[1B][0m...
         Starting [1B][0;1;39mOpenBSD Secure Shell server[1B][0m...
         Starting [1B][0;1;39mHostname Service[1B][0m...
         Starting [1B][0;1;39mPermit User Sessions[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mODROID Specific System Tweaks[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39m/etc/rc.local Compatibility[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mPermit User Sessions[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mModem Manager[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mOpenBSD Secure Shell server[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mHostname Service[1B][0m.
         Starting [1B][0;1;39mNetwork Manager Script Dispatcher Service[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mSerial Getty on ttySAC2[1B][0m.
         Starting [1B][0;1;39mSet console scheme[1B][0m...
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mLSB: set CPUFreq kernel parameters[1B][0m.
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mSet console scheme[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mNetwork Manager Script Dispatcher Service[1B][0m.
[[1B][0;32m  OK  [1B][0m] Created slice [1B][0;1;39mSlice /system/getty[1B][0m.
[[1B][0;32m  OK  [1B][0m] Started [1B][0;1;39mGetty on tty1[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mLogin Prompts[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mMulti-User System[1B][0m.
[[1B][0;32m  OK  [1B][0m] Reached target [1B][0;1;39mGraphical Interface[1B][0m.
         Starting [1B][0;1;39mRecord Runlevel Change in UTMP[1B][0m...
[[1B][0;32m  OK  [1B][0m] Finished [1B][0;1;39mRecord Runlevel Change in UTMP[1B][0m.


Ubuntu 22.04.3 LTS odroid ttySAC2

odroid login: 

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

Nope, no need.
the reason why its broken is due to you not having all the kernel modules.
You have a single kernel image with ethernet support :)

Now, what's gonna happen is, I'm going to release a full kernel package today, in 1~2 hours, you will update normally.
apt update && apt dist-upgrade

Everything will be back to normal :)
These users thanked the author mdrjr for the post:
matty67 (Thu Feb 08, 2024 10:37 pm)

mdrjr
Site Admin
Posts: 12086
Joined: Fri Feb 22, 2013 11:34 pm
languages_spoken: english, portuguese
ODROIDs: -
Location: Brazil
Has thanked: 8 times
Been thanked: 150 times
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by mdrjr »

There we go!

You can now run
sudo apt update
sudo apt dist-upgrade
You will get the latest kernel with the latest updates :)

And thank you so much for helping with this issue!
These users thanked the author mdrjr for the post:
matty67 (Thu Feb 08, 2024 11:17 pm)

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Yes. Everything is working now. Thanks for your quick help.
These users thanked the author matty67 for the post:
mdrjr (Thu Feb 08, 2024 11:36 pm)

matty67
Posts: 11
Joined: Tue Feb 06, 2024 4:50 pm
languages_spoken: german english (basic)
ODROIDs: XU4
Location: Germany
Has thanked: 5 times
Been thanked: 1 time
Contact:

Re: [SOLVED] HARDWARE PROTECTION shutdown (Temperature too high)

Post by matty67 »

Hi, thats me again.
Now I have problems with the temperature.
Sometimes the fan runs and runs. When I monitor the temperature there are values with a minus.
Do have any idea?

Every 2.0s: cat /sys/devices/virtual/thermal/thermal_zone0/temp /sys/dev... odroid: Tue Feb 13 17:47:51 2024

-22000
-21000
40000
38000
36000

Post Reply

Return to “Linux Kernel 6.1 Development Party”

Who is online

Users browsing this forum: No registered users and 1 guest