Last December I purchased an N2L for use on a project that requires ethernet and a headless SBC. As there is no ethernet onboard, I also purchased a USB 3.0 to gigabit ethernet LAN network adapter by Aceele. I just plugged it to the N2L USB 3.0 port and it worked right away. It continued to work fine until last week when I noticed that I could not connect using ssh. The N2L was still running fine (blue LED flashing) so I unplugged the adapter and then plugged it in again. That restart of the adapter got the ethernet connection working again. Looking at the log there was an error listed something like TX error -71. It seemed to work fine again after that but a couple of days later I got the same error and loss of the connection again. Thinking that this might continue I purchased another adapter by Atolla to test.
When I plugged it in I could not get connected on ssh. When I looked on the Atolla website I found that they had a Linux driver download to install an r8153 module. I did the download and install on the N2L using the original Aceele adapter but the Atolla still did not work. So then I went back to the Aceele adapter and of course it did not work either. I then plugged a monitor into the HDMI port and connected a keyboard to the USB port. I was able to login so I blacklisted the driver and updated the initramfs but still neither adapter would work.
I contacted Atolla who said that the adapter should have worked out of the box without installing the driver and they would be happy to receive it back for a refund. But of course the real problem is that I cannot get any adapter work. I did notice that the lights on the RJ45 port on the adapter are working fine so the problem seems to be that the ethernet signal is not getting to the N2L on the USB port.
Since I can login, and can run any commands to help sort out the problem, I am able to make any changes required but I do not know where to begin to troubleshoot any further. Any guidance will be gratefully accepted.
Thanks
USB to ethernet adapter not working on N2L
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
-
tobetter
- Posts: 11949
- Joined: Mon Feb 25, 2013 10:55 am
- languages_spoken: Korean, English
- ODROIDs: Many
- Location: Paju, South Korea
- Has thanked: 834 times
- Been thanked: 2016 times
- Contact:
Re: USB to ethernet adapter not working on N2L
Have you tried to connect to to lower port (USB 2.0) and test it?
Please share the output of uname -a as well as the log with dmesg when your adaptor does not work.
Please share the output of uname -a as well as the log with dmesg when your adaptor does not work.
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
@tobetter there is some good news: when I plug in the original Aceele adapter to the lower USB port (USB 2.0) I can get a connection on ssh.
Using that connection here is uname -a:
This is dmesg after a reboot with the Aceele adapter plugged into USB 2.0:
This is dmesg after plugging the Atolla adapter into the upper USB port (USB 3.0):
If I move the ethernet cable from the Aceele adapter to the Atolla adapter, the ssh connection is lost although the lights on the RJ45 port on the Atolla adapter are working as they should.
This is dmesg after plugging the ethernet cable back into the Aceele adapter and reconnecting via ssh:
This is dmesg after moving the Aceele adapter from USB 2.0 to USB 3.0 then back to USB 2.0:
So it seems that I can connect via ssh with the Aceele adapter in USB 2.0 but of course I will not get a gigabit connection, only a 100 megabit. Better than nothing but I really do want to get the gigabit connection working. Please advise if you need more testing or command output. Thanks.
Using that connection here is uname -a:
Code: Select all
$ uname -a
Linux nl 4.9.333-25 #1 SMP PREEMPT Thu Nov 24 22:04:44 UTC 2022 aarch64 aarch64 aarch64 GNU/LinuxCode: Select all
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.333-25 (root@builder_n2) (gcc version 11.2.0 (Ubuntu 11.2.0-19ubuntu1) ) #1 SMP PREEMPT Thu Nov 24 22:04:44 UTC 2022
[ 0.000000] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000] Machine model: Hardkernel ODROID-N2L
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] __reserved_mem_alloc_size, start:0x000000007f800000, end:0x0000000080000000, len:8 MiB
[ 0.000000] failed to allocate memory for node linux,meson-fb, size:8 MB
[ 0.000000] 70000000 - 78000000, 131072 KB, linux,ion-dev
[ 0.000000] 6d800000 - 70000000, 40960 KB, linux,di_cma
[ 0.000000] Reserved memory: created DMA memory pool at 0x000000006d800000, size 0 MiB
[ 0.000000] 6d800000 - 6d800000, 0 KB, linux,ppmgr
[ 0.000000] 5a400000 - 6d800000, 315392 KB, linux,codec_mm_cma
[ 0.000000] 5a400000 - 5a400000, 0 KB, linux,codec_mm_reserved
[ 0.000000] __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000] 05000000 - 05400000, 4096 KB, linux,secmon
[ 0.000000] cma: Reserved 8 MiB at 0x0000000059c00000
[ 0.000000] On node 0 totalpages: 491520
[ 0.000000] DMA zone: 7680 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 491520 pages, LIFO batch:31
[ 0.000000] psci: probing for conduit method from DT.
[ 0.000000] psci: PSCIv1.0 detected in firmware.
[ 0.000000] psci: Using standard PSCI v0.2 function IDs
[ 0.000000] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000] psci: SMC Calling Convention v1.1
[ 0.000000] percpu: Embedded 21 pages/cpu s48472 r8192 d29352 u86016
[ 0.000000] pcpu-alloc: s48472 r8192 d29352 u86016 alloc=21*4096
[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [0] 4 [0] 5
[ 0.000000] Detected VIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 483840
[ 0.000000] Kernel command line: root=UUID=e139ce78-9841-40fe-8823-96a304a09859 rootwait rw console=ttyS0,115200n8 no_console_suspend fsck.repair=yes net.ifnames=0 elevator=noop hdmimode=custombuilt cvbsmode=576cvbs max_freq_a53=2016 max_freq_a73=2400 maxcpus=6 voutmode=hdmi modeline=1920,1080,148500,67500,60,1920,2008,2052,2200,1080,1084,1089,1125,1,1,1 disablehpd=false cvbscable= overscan=100 monitor_onoff=false logo=osd0,loaded hdmitx=cec3f sdrmode=auto consoleblank=0 enable_wol=0
[ 0.000000] vout: get hdmimode: custombuilt
[ 0.000000] vout: get cvbsmode: 576cvbs
[ 0.000000] max cpufreq of cluster0 : 2016000kHz
[ 0.000000] max cpufreq of cluster1 : 2400000kHz
[ 0.000000] hdmitx: voutmode : 1
[ 0.000000] fmt_para.timing
[ 0.000000] - pixel_freq 148500, frac_freq 148500
[ 0.000000] - h_freq 67500, v_freq 60000
[ 0.000000] - hsync_polarity 1, vsync_polarity 1
[ 0.000000] - h_active 1920, h_total 2200
[ 0.000000] - h_blank 280, h_front 88, h_sync 44, h_back 148
[ 0.000000] - v_active 1080, v_total 1125
[ 0.000000] - v_blank 45, v_front 4, v_sync 5, v_back 36
[ 0.000000] - v_sync_ln 1
[ 0.000000] fmt_para.hdmitx_vinfo
[ 0.000000] - name custombuilt, mode 0
[ 0.000000] - width 1920, height 1080, field_height 1080
[ 0.000000] - aspect_ratio_num 16, aspect_ratio_den 9
[ 0.000000] - video_clk 148500000
[ 0.000000] - htotal 2200, vtotal 1125
[ 0.000000] - viu_color_fmt 2, viu_mux 2
[ 0.000000] fb: osd0
[ 0.000000] fb: loaded
[ 0.000000] hdmitx: HDMI hdmi_cec_func_config:0x3f
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.000000] Memory: 1394864K/1966080K available (12476K kernel code, 1814K rwdata, 7860K rodata, 4992K init, 1420K bss, 71504K reserved, 499712K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000] .text : 0xffffff8009080000 - 0xffffff8009cb0000 ( 12480 KB)
[ 0.000000] .rodata : 0xffffff8009cb0000 - 0xffffff800a470000 ( 7936 KB)
[ 0.000000] .init : 0xffffff800a470000 - 0xffffff800a950000 ( 4992 KB)
[ 0.000000] .data : 0xffffff800a950000 - 0xffffff800ab15a00 ( 1815 KB)
[ 0.000000] .bss : 0xffffff800ab15a00 - 0xffffff800ac78ac4 ( 1421 KB)
[ 0.000000] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000] 0xffffffbf00000000 - 0xffffffbf01e00000 ( 30 MB actual)
[ 0.000000] memory : 0xffffffc000000000 - 0xffffffc078000000 ( 1920 MB)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GPIO-INTC: support to detect double-edge trigger signal
[ 0.000000] g12a_aoclkc_init: register ao clk ok!
[ 0.000000] Meson chip version = RevC (29:C - 40:0)
[ 0.000000] meson_g12a_sdemmc_init: register amlogic sdemmc clk
[ 0.000000] meson_g12a_sdemmc_init: register amlogic sdemmc clk
[ 0.000000] meson_g12a_gpu_init: register meson gpu clk
[ 0.000000] meson_g12a_media_init: register meson media clk
[ 0.000000] meson_g12a_misc_init: register amlogic g12a misc clks
[ 0.000000] meson_g12a_misc_init: done.
[ 0.000000] g12a_clkc_init initialization complete
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000003] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000039] meson_bc_timer: mclk->mux_reg =ffffff800800c190,mclk->reg =ffffff800800e194
[ 0.000574] Console: colour dummy device 80x25
[ 0.000591] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.000599] pid_max: default: 32768 minimum: 301
[ 0.000691] Security Framework initialized
[ 0.000711] AppArmor: AppArmor initialized
[ 0.000742] Mount-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000749] Mountpoint-cache hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.001319] ftrace: allocating 39436 entries in 155 pages
[ 0.068285] sched-energy: Sched-energy-costs installed from DT
[ 0.068298] CPU0: update cpu_capacity 631
[ 0.079907] ASID allocator initialised with 65536 entries
[ 0.114425] secmon: clear_range:5100000 200000
[ 0.114972] EFI services will not be available.
[ 0.160491] Detected VIPT I-cache on CPU1
[ 0.160540] CPU1: update cpu_capacity 631
[ 0.160542] CPU1: Booted secondary processor [410fd034]
[ 0.193013] CPU features: enabling workaround for Spectre-BHB
[ 0.193020] Detected VIPT I-cache on CPU2
[ 0.193062] CPU2: update cpu_capacity 1192
[ 0.193064] CPU2: Booted secondary processor [410fd092]
[ 0.224570] Detected VIPT I-cache on CPU3
[ 0.224592] CPU3: update cpu_capacity 1192
[ 0.224594] CPU3: Booted secondary processor [410fd092]
[ 0.256630] Detected VIPT I-cache on CPU4
[ 0.256652] CPU4: update cpu_capacity 1192
[ 0.256654] CPU4: Booted secondary processor [410fd092]
[ 0.288694] Detected VIPT I-cache on CPU5
[ 0.288716] CPU5: update cpu_capacity 1192
[ 0.288718] CPU5: Booted secondary processor [410fd092]
[ 0.288804] Brought up 6 CPUs
[ 0.288846] SMP: Total of 6 processors activated.
[ 0.288854] CPU features: detected feature: 32-bit EL0 Support
[ 0.289046] CPU: All CPU(s) started at EL2
[ 0.289075] alternatives: patching kernel code
[ 0.290399] devtmpfs: initialized
[ 0.301529] DMI not present or invalid.
[ 0.301681] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.301694] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.301795] pinctrl core: initialized pinctrl subsystem
[ 0.302461] NET: Registered protocol family 16
[ 0.302909] schedtune: init normalization constants...
[ 0.302918] schedtune: CLUSTER[0-1] min_pwr: 0 max_pwr: 42
[ 0.302923] schedtune: CPU[0] min_pwr: 0 max_pwr: 279
[ 0.302928] schedtune: CPU[1] min_pwr: 0 max_pwr: 279
[ 0.302933] schedtune: CLUSTER[2-5] min_pwr: 0 max_pwr: 110
[ 0.302937] schedtune: CPU[2] min_pwr: 0 max_pwr: 1048
[ 0.302941] schedtune: CPU[3] min_pwr: 0 max_pwr: 1048
[ 0.302944] schedtune: CPU[4] min_pwr: 0 max_pwr: 1048
[ 0.302948] schedtune: CPU[5] min_pwr: 0 max_pwr: 1048
[ 0.302951] schedtune: SYSTEM min_pwr: 0 max_pwr: 4902
[ 0.302955] schedtune: using normalization constants mul: 2882587190 sh1: 1 sh2: 12
[ 0.302958] schedtune: verify normalization constants...
[ 0.302962] schedtune: max_pwr/2^0: 4902 => norm_pwr: 1024
[ 0.302965] schedtune: max_pwr/2^1: 2451 => norm_pwr: 512
[ 0.302969] schedtune: max_pwr/2^2: 1225 => norm_pwr: 255
[ 0.302972] schedtune: max_pwr/2^3: 612 => norm_pwr: 127
[ 0.302975] schedtune: max_pwr/2^4: 306 => norm_pwr: 63
[ 0.302978] schedtune: max_pwr/2^5: 153 => norm_pwr: 31
[ 0.302982] schedtune: configured to support 5 boost groups
[ 0.313278] cpuidle: using governor menu
[ 0.313381] register canvas platform driver
[ 0.313409] register rdma platform driver
[ 0.314021] vdso: 2 pages (1 code @ ffffff8009cb7000, 1 data @ ffffff800a955000)
[ 0.314039] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.315557] DMA: preallocated 2048 KiB pool for atomic allocations
[ 0.315758] clkmsr: clkmsr: driver init
[ 0.315764] codec_mm_module_init
[ 0.315790] media_configs_system_init
[ 0.318028] aml_iomap: amlogic iomap probe done
[ 0.318528] vpu: driver version: v20190329(8-g12b)
[ 0.318539] vpu: load vpu_clk: 666666667Hz(7)
[ 0.318712] vpu: clktree_init
[ 0.318779] vpu: vpu_probe OK
[ 0.323393] clkmsr: msr_clk_reg0=ffffff800823a004,msr_clk_reg2=ffffff800823c00c
[ 0.323406] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.325916] audio_clocks: audio_clocks_probe done
[ 0.328097] aml_vdac_config_probe: cpu_id:4, name:meson-g12ab-vdac
[ 0.328302] aml_vdac_probe: ok
[ 0.328473] canvas_probe reg=00000000ff638000,size=2000
[ 0.328492] canvas maped reg_base =ffffff8008268000
[ 0.334654] rdma_probe,cpu_type:0, ver:0, len:8
[ 0.334885] rdma_register, rdma_table_addr ffffff8008277000 rdma_table_addr_phy 59e00000 reg_buf ffffffc056d60000
[ 0.334892] rdma_register success, handle 1 table_size 32768
[ 0.334897] set_rdma_handle video rdma handle = 1.
[ 0.334945] classs created ok
[ 0.334958] classs file created ok
[ 0.335951] aml_snd_reg_map[0], reg:ff640000, size:2000
[ 0.335968] aml_snd_reg_map[1], reg:ff642000, size:2000
[ 0.335979] aml_snd_reg_map[2], reg:ff64a000, size:2000
[ 0.335989] aml_snd_reg_map[3], reg:ff656000, size:1800
[ 0.336007] aml_snd_reg_map[4], reg:ffd01000, size:1000
[ 0.336011] amlogic auge_snd_iomap probe done
[ 0.338207] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
[ 0.338333] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
[ 0.338339] codec_mm_probe ok
[ 0.339204] cvbs_out: cvbsout_probe, cpu_id:5,name:meson-g12b-cvbsout
[ 0.339220] cvbs_out: clk path:0
[ 0.339227] cvbs_out: cvbs trimming.1.v5: 0xa0, 0x0
[ 0.339359] vout: vout1: register server: cvbs_vout_server
[ 0.339364] cvbs_out: register cvbs module server ok
[ 0.339369] vout: vout2: register server: cvbs_vout2_server
[ 0.339373] cvbs_out: register cvbs module vout2 server ok
[ 0.339379] cvbs_out: chrdev devno 264241152 for disp
[ 0.339562] cvbs_out: create cdev cvbs
[ 0.339569] cvbs_out: cvbsout_probe OK
[ 0.467041] SCSI subsystem initialized
[ 0.467222] usbcore: registered new interface driver usbfs
[ 0.467272] usbcore: registered new interface driver hub
[ 0.467310] usbcore: registered new device driver usb
[ 0.467410] media: Linux media interface: v0.10
[ 0.467444] Linux video capture interface: v2.00
[ 0.467526] pps_core: LinuxPPS API ver. 1 registered
[ 0.467530] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.467547] PTP clock support registered
[ 0.467649] dmi: Firmware registration failed.
[ 0.467900] secmon: reserve_mem_size:0x300000
[ 0.467975] secmon secmon: assigned reserved memory node linux,secmon
[ 0.468143] secmon: get page:ffffffbf00140000, 5000
[ 0.468148] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.468152] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.468583] hdmitx: system: amhdmitx_probe start
[ 0.468588] hdmitx: system: Ver: 20190815
[ 0.468614] hdmitx: system: hdmitx_device.chip_type : 11
[ 0.468637] hdmitx: system: not find match pwr-ctl
[ 0.468667] hdmitx: system: not find drm_amhdmitx
[ 0.468686] hdmitx: system: hpd irq = 42
[ 0.468768] hdmitx: system: hdcp22_tx_skp failed to probe
[ 0.468772] hdmitx: system: hdcp22_tx_esm failed to probe
[ 0.469089] vout: vout1: register server: hdmitx_vout_server
[ 0.469095] vout: vout2: register server: hdmitx_vout2_server
[ 0.469454] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
[ 0.469484] hdmitx: hdmitx20: Mapped PHY: 0xff634400
[ 0.469492] hdmitx: hdmitx20: Mapped PHY: 0xff900000
[ 0.469509] hdmitx: hdmitx20: Mapped PHY: 0xff800000
[ 0.469514] hdmitx: hdmitx20: Mapped PHY: 0xff63c000
[ 0.469520] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
[ 0.469524] hdmitx: hdmitx20: Mapped PHY: 0xff608000
[ 0.469527] hdmitx: hdmitx20: Mapped PHY: 0xff600000
[ 0.469531] hdmitx: hdmitx20: Mapped PHY: 0xffe01000
[ 0.469539] hdmitx: hw: alread display in uboot 0x10
[ 0.469562] hdmitx: hw: avmute set to 1
[ 0.469568] hdmitx: system: fmt_attr 444,8bit
[ 0.469571] hdmitx: system: fmt_attr 444,8bit
[ 0.469680] hdmitx: system: amhdmitx_probe end
[ 0.469882] vout: create vout attribute OK
[ 0.470027] vout: vout_fops_create OK
[ 0.470031] vout: vout1: register server: nulldisp_vout_server
[ 0.470086] vout: tvout monitor interval:500(ms), timeout cnt:20
[ 0.470115] hdmitx: hdmitx_set_current_vmode[3878]
[ 0.470119] hdmitx: system: recalc before custombuilt 60 1
[ 0.470124] hdmitx: system: recalc after custombuilt 60 1
[ 0.470131] hdmitx: system: irq 80000002 0
[ 0.470133] hdmitx: system: get current mode: custombuilt
[ 0.470139] hdmitx: system: update rx hdr info 0
[ 0.470143] hdmitx: system: update physcial size: 16 9
[ 0.470177] hdmitx: video: already init VIC = 0 Now VIC = 116
[ 0.470183] hdmitx: [hdmitx_set_display] output_rgb 0, cs 0
[ 0.470186] hdmitx: video: rx edid only support RGB format
[ 0.470190] hdmitx: hw: div40: 0
[ 0.499516] hdmitx: ddc w1b error 0x54 0x20 0x00
[ 0.499522] hdmitx: this mode doesn't have frac_rate
[ 0.499525] hdmitx: frac_rate = 1
[ 0.499531] hdmitx: [hdmitx_set_clk_] vic == HDMI_CUSTOMBUILT, frac_freq 148500
[ 0.499535] hdmitx: hpll_clk_out 2970000, od1 2, od2 1, od3 2
[ 0.499539] hdmitx: config HPLL = 2970000 frac_rate = 0
[ 0.499595] hdmitx: HPLL: 0xdb00047b
[ 0.499598] hdmitx: config HPLL done
[ 0.499604] hdmitx: set_hpll_od3_clk_div[643] div = 6
[ 0.499610] hdmitx: j = 15 vid_clk_div = 1
[ 0.541539] hdmitx: hw: config hdmitx IP vic = 116 cd:4 cs: 0
[ 0.551629] hdmitx: video: Sink is HDMI device
[ 0.551661] hdmitx: hw: set audio
[ 0.551666] hdmitx: hw: hdmitx tx_aud_src = 0
[ 0.551679] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 0.551683] hdmitx: hw: aud_n_para = 6144
[ 0.551691] hdmitx: hw: set channel status
[ 0.551723] vout: init mode custombuilt set ok
[ 0.551726] vout: aml_tvout_mode_monitor
[ 0.551740] vout: aml_vout_probe OK
[ 0.552261] chip type:0x29
[ 0.552457] MEMORY:[0+78000000]
[ 0.552462] ramdump_probe, storage device:data
[ 0.552466] NO valid ramdump args:0 0
[ 0.552473] ramdump_probe, set sticky to 8780
[ 0.552580] Advanced Linux Sound Architecture Driver Initialized.
[ 0.553266] NetLabel: Initializing
[ 0.553271] NetLabel: domain hash size = 128
[ 0.553275] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.553306] NetLabel: unlabeled traffic allowed by default
[ 0.554007] clocksource: Switched to clocksource arch_sys_counter
[ 0.597584] VFS: Disk quotas dquot_6.6.0
[ 0.597633] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.597805] AppArmor: AppArmor Filesystem Enabled
[ 0.604737] NET: Registered protocol family 2
[ 0.604834] IP idents hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.605882] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.605958] TCP bind hash table entries: 16384 (order: 6, 262144 bytes)
[ 0.606081] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.606161] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.606181] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.606296] NET: Registered protocol family 1
[ 0.606315] PCI: CLS 0 bytes, default 64
[ 0.607508] Trying to unpack rootfs image as initramfs...
[ 0.824812] Now can use cma, free:13251, wm:14080
[ 0.933960] clear:6e800000, free:6e800000, tick:357761 us
[ 0.998205] hdmitx: system: plugin
[ 1.130467] hdmitx: edid: EDID Parser:
[ 1.130473] hdmitx: hdmitx: reach vesa idx MAX
[ 1.130477] hdmitx: hdmitx: reach vesa idx MAX
[ 1.130481] hdmitx: hdmitx: reach vesa idx MAX
[ 1.130489] [RX]-up_phy_addr = 1
[ 1.130505] hdmitx: edid: get dtd0 vic: 5
[ 1.130511] hdmitx: hdmitx: get PMT vic: 16
[ 1.130516] hdmitx: edid: find IEEEOUT
[ 1.130546] hdmitx: edid: check sum valid
[ 1.130550] hdmitx: edid: check sum valid
[ 1.130557] hdmitx: edid: update rx hdr info 0 at edid parsing
[ 1.130564] hdmitx: edid: check sum valid
[ 1.130568] hdmitx: edid: check sum valid
[ 1.130573] hdmitx: edid: blk0 raw data
[ 1.130613] hdmitx: edid:
00ffffffffffff00593a7000010101010014010380301b782a1815a45d53a427
135054a54e0001010101010101010101010101010101023a801871382d40582c
4500dc0c1100001e000000ff000a202020202020202020202020000000fc004d
32323056412d43410a202020000000fd003a4c1e460f000a20202020202001d1
[ 1.130627] hdmitx: edid: blk1 raw data
[ 1.130666] hdmitx: edid:
02031e71480504900203070601260907071507508301000065030c001000011d
8018711c1620582c2500dc0c1100009e011d007251d01e206e285500dc0c1100
001e8c0ad08a20e02d10103e9600650c110000188c0aa01451f01600267c4300
dc0c110000988c0aa01451f01600267c4300650c1100009800000000000000bb
[ 1.130682] hdmitx: system: update physcial size: 480 270
[ 1.130686] hdmitx: video: Sink is HDMI device
[ 1.130693] hdmitx: hw: set audio
[ 1.130697] hdmitx: hw: hdmitx tx_aud_src = 0
[ 1.130711] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[ 1.130716] hdmitx: hw: aud_n_para = 6144
[ 1.130725] hdmitx: hw: set channel status
[ 1.130757] hdmitx: system: get current mode: custombuilt
[ 1.130761] hdmitx: system: update rx hdr info 0
[ 1.130766] hdmitx: system: update physcial size: 480 270
[ 1.130801] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 116
[ 1.130806] hdmitx: system: change to HDMI mode
[ 2.890701] Freeing initrd memory: 7852K
[ 2.895048] hw perfevents: clusterb_enabled = 1
[ 2.895056] hw perfevents: cpumasks 0x3, 0x3c
[ 2.895079] hw perfevents: cluster A irq = 18
[ 2.895105] hw perfevents: cluster B irq = 19
[ 2.895156] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 2.896837] audit: initializing netlink subsys (disabled)
[ 2.896889] audit: type=2000 audit(2.852:1): initialized
[ 2.897480] workingset: timestamp_bits=46 max_order=19 bucket_order=0
[ 2.903218] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.903361] Registering sdcardfs 0.1
[ 2.906552] NET: Registered protocol family 38
[ 2.906562] Key type asymmetric registered
[ 2.906567] Asymmetric key parser 'x509' registered
[ 2.906685] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 2.906758] io scheduler noop registered (default)
[ 2.906762] io scheduler deadline registered
[ 2.906784] io scheduler cfq registered
[ 2.907093] pwm-gpio pwmgpio: 1 gpio pwms loaded
[ 2.908125] meson-pwm ff802000.pwm: pwm pinmux : can't get pinctrl
[ 2.908321] meson-pwm ffd1b000.pwm: pwm pinmux : can't get pinctrl
[ 2.908833] random: crng init done
[ 2.909015] gpiomem-aml ff634000.gpiomem: Initialised: GPIO register area is 1
[ 2.909107] gpiomem-aml ff634000.gpiomem: Initialised: Registers at start:0xff634000 end:0xff634fff size:0x00000fff
[ 2.909168] [drm] Initialized
[ 2.909227] mali ffe40000.bifrost: Continuing without Mali regulator control
[ 2.909279] mali ffe40000.bifrost: max pp is 2
[ 2.909285] mali ffe40000.bifrost: set min pp to default 1
[ 2.909289] mali ffe40000.bifrost: min pp is 1
[ 2.909294] mali ffe40000.bifrost: min clk is 4
[ 2.909308] mali ffe40000.bifrost: hiu io source 0xffffff80083c8000
[ 2.909316] mali ffe40000.bifrost: hiu io source 0xffffff80083ca000
[ 2.909321] mali ffe40000.bifrost: num of pp used most of time 1
[ 2.909326] mali ffe40000.bifrost: clock dvfs cfg table size is 6
[ 2.909345] mali ffe40000.bifrost: max clk set 4
[ 2.909349] mali ffe40000.bifrost: max clk is 4
[ 2.909353] mali ffe40000.bifrost: turbo clk set to 5
[ 2.909357] mali ffe40000.bifrost: turbo clk is 5
[ 2.909362] mali ffe40000.bifrost: default clk set to 4
[ 2.909366] mali ffe40000.bifrost: default clk is 4
[ 2.909373] mali ffe40000.bifrost: ====================0====================
clk_freq= 285714285, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshod=<100 190>, clk_sample=285
[ 2.909381] mali ffe40000.bifrost: ====================1====================
clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshod=<152 207>, clk_sample=400
[ 2.909389] mali ffe40000.bifrost: ====================2====================
clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<180 220>, clk_sample=500
[ 2.909396] mali ffe40000.bifrost: ====================3====================
clk_freq= 666666666, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshod=<210 236>, clk_sample=666
[ 2.909403] mali ffe40000.bifrost: ====================4====================
clk_freq= 800000000, clk_parent=fclk_div2p5, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=800
[ 2.909411] mali ffe40000.bifrost: ====================5====================
clk_freq= 800000000, clk_parent=fclk_div2p5, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=800
[ 2.909416] mali ffe40000.bifrost: clock dvfs table size is 6
[ 2.909494] mali_plat=ffffff800a9e7098
[ 2.909586] meson_gcooldev is null, no set min status
[ 2.909590] gpu cooling register okay with err=0
[ 2.909634] meson_gcooldev is null, no set min status
[ 2.909638] gpu core cooling register okay with err=0
[ 2.909659] shader_present=3, tiler_present=1, l2_present=1
[ 2.909745] Mali_pwr_on:gpu_irq : 200
[ 2.909937] mali ffe40000.bifrost: GPU identified as 0x2 arch 7.2.1 r0p0 status 0
[ 2.910099] mali ffe40000.bifrost: Using coherency mode 0 set from dtb
[ 2.910768] mali ffe40000.bifrost: Probed as mali0
[ 2.911089] Unable to detect cache hierarchy for CPU 0
[ 2.916282] brd: module loaded
[ 3.012924] loop: module loaded
[ 3.013203] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 3.014365] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.014372] ehci-pci: EHCI PCI platform driver
[ 3.014432] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 3.014715] usbcore: registered new interface driver cdc_acm
[ 3.014719] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 3.014756] usbcore: registered new interface driver usb-storage
[ 3.014819] usbcore: registered new interface driver usbserial
[ 3.014846] usbcore: registered new interface driver usbserial_generic
[ 3.014867] usbserial: USB Serial support registered for generic
[ 3.015089] mousedev: PS/2 mouse device common for all mice
[ 3.015321] i2c /dev entries driver
[ 3.017068] lirc_helper: wakeupkey 0xffffffff, protocol 0x1
[ 3.018270] ledtrig-cpu: registered to indicate activity on CPUs
[ 3.018502] hidraw: raw HID events driver (C) Jiri Kosina
[ 3.018687] usbcore: registered new interface driver usbhid
[ 3.018691] usbhid: USB HID core driver
[ 3.019021] meson_cpufreq_init: ignor dsu clk!
[ 3.019027] meson_cpufreq_init: ignor dsu pre parent clk!
[ 3.019059] value of voltage_tolerance 0
[ 3.019063] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
[ 3.019066] value of gp1_clk_target 0
[ 3.019510] cpu cpu0: meson_cpufreq_init: CPU 0 initialized
[ 3.020585] meson_cpufreq_init: ignor dsu clk!
[ 3.020590] meson_cpufreq_init: ignor dsu pre parent clk!
[ 3.020647] value of voltage_tolerance 0
[ 3.020651] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
[ 3.020654] value of gp1_clk_target 0
[ 3.021245] cpu cpu2: meson_cpufreq_init: CPU 2 initialized
[ 3.022301] ff803000.serial: clock gate not found
[ 3.022320] meson_uart ff803000.serial: ==uart0 reg addr = ffffff80085b4000
[ 3.022338] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 32, base_baud = 1500000) is a meson_uart
[ 3.022346] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[ 5.421819] console [ttyS0] enabled
[ 5.425677] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff80085b6000
[ 5.432578] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 41, base_baud = 1500000) is a meson_uart
[ 5.442294] amlogic-new-usb2-v2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff80085d9000
[ 5.452891] amlogic-new-usb3-v2 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff80083fe080
[ 5.464190] aml_dma ff63e000.aml_dma: Aml dma
[ 5.468518] aml_aes_dma ff63e000.aml_dma:aml_aes: Aml AES_dma
[ 5.474120] aml_tdes_dma ff63e000.aml_dma:aml_tdes: Aml TDES_dma
[ 5.480356] aml_sha_dma ff63e000.aml_dma:aml_sha: Aml SHA1/SHA224/SHA256 dma
[ 5.487400] gpio-keypad: probe of ff800000.gpio_keypad failed with error -22
[ 5.494635] efusekeynum: 1
[ 5.497392] efusekeyname: uuid offset: 0 size: 32
[ 5.503872] efuse efuse: probe OK!
[ 5.507984] ion_dev soc:ion_dev: assigned reserved memory node linux,ion-dev
[ 5.514701] ge2d: ge2d_init_module
[ 5.518175] ge2d: ge2d_dev major:236
[ 5.521902] ge2d: clock source clk_ge2d_gate ffffffc049046840
[ 5.527737] ge2d: clock clk_ge2d source ffffffc053e8ac00
[ 5.533187] ge2d: clock source clk_vapb_0 ffffffc053e8ae80
[ 5.538816] ge2d: ge2d init clock is 500000000 HZ, VPU clock is 666666656 HZ
[ 5.546071] ge2d: ge2d clock is 499 MHZ
[ 5.549999] ge2d: find address resource
[ 5.553982] ge2d: map io source 0x00000000ff940000,size=65536 to 0xffffff8008710000
[ 5.561780] ge2d: reserved mem init failed
[ 5.566028] ge2d: ge2d: pdev=ffffffc056ec3800, irq=45, clk=ffffffc049046840
[ 5.573149] ge2d: ge2d start monitor
[ 5.576884] ge2d: ge2d workqueue monitor start
[ 5.577024] [tsync_pcr_init]init success.
[ 5.577086] amvideom vsync irq: 46
[ 5.577098] create_ge2d_work_queue video task ok
[ 5.577312] fb: osd_init_module
[ 5.577427] fb: viu vsync irq: 46
[ 5.577431] fb: viu2 vsync irq: 55
[ 5.577471] 0x000000db:Y=db,U=0,V=0
[ 5.577472] 0x000000dc:Y=dc,U=0,V=0
[ 5.577473] 0x000000dd:Y=dd,U=0,V=0
[ 5.577474] 0x000000de:Y=de,U=0,V=0
[ 5.577474] 0x000000df:Y=df,U=0,V=0
[ 5.577475] 0x000000e0:Y=e0,U=0,V=0
[ 5.581524] fb: osd_rdma_init: rdma_table p=0x59e08000,op=0x59e08000 , v=0xffffff80085ed000
[ 5.581535] rdma_register, rdma_table_addr ffffff80085ef000 rdma_table_addr_phy 59e09000 reg_buf ffffffc053ebe000
[ 5.581536] rdma_register success, handle 2 table_size 4096
[ 5.581537] fb: osd_rdma_init:osd rdma handle = 2.
[ 5.581542] fb: mem_size: 0x800000
[ 5.581543] fb: mem_size: 0x4b80000
[ 5.581543] fb: mem_size: 0x100000
[ 5.581544] fb: mem_size: 0x100000
[ 5.581544] fb: mem_size: 0x800000
[ 5.581567] fb: failed to init reserved memory
[ 5.581572] fb: fb def : 1920 1080 1920 2160 32
[ 5.581573] fb: init fbdev bpp is:32
[ 5.686503] fb: malloc_osd_memory, cma:ffffff800abd0ec8
[ 5.686504] fb: malloc_osd_memory, 1231, base:0x0000000059c00000, size:8388608
[ 5.686511] fb: use ion buffer for fb memory, fb_index=0
[ 5.686512] fb: OSD0 as afbcd mode,afbc_type=2
[ 5.706301] meson-fb meson-fb: create ion_client ffffffc052cbad80, handle=ffffffc052cb3680
[ 5.706304] meson-fb meson-fb: ion memory(0): created fb at 0x0000000070000000, size 75 MiB
[ 5.706305] fb: 0, phy: 0x0000000070000000, vir:0xffffff800bc80000, size=77312K
[ 5.706307] fb: Frame buffer memory assigned at
[ 5.706307] fb: 0, phy: 0x0000000070000000, vir:0xffffff800bc80000, size=77312K
[ 5.706308] fb: 0, phy: 0x0000000070000000, vir:0xffffff800bc80000, size=77312K
[ 5.706309] fb: logo_index=0,fb_index=0
[ 5.706310] fb: ---------------clear fb0 memory ffffff800bc80000
[ 5.714265] fb: osd[0] canvas.idx =0x40
[ 5.714265] fb: osd[0] canvas.addr=0x70000000
[ 5.714266] fb: osd[0] canvas.width=7680
[ 5.714266] fb: osd[0] canvas.height=2160
[ 5.714267] fb: osd[0] frame.width=1920
[ 5.714267] fb: osd[0] frame.height=1080
[ 5.714268] fb: osd[0] out_addr_id =0x1
[ 5.741527] Console: switching to colour frame buffer device 240x67
[ 5.866315] fb: osd[0] enable: 1 (swapper/0)
[ 5.883321] fb: set osd0 reverse as NONE
[ 5.899669] fb: osd probe OK
[ 5.899779] hdmitx: hdcp: hdmitx_hdcp_init
[ 5.901480] vout: vout2: create vout2 attribute OK
[ 5.906344] vout: vout2: vout2_fops_create OK
[ 5.910877] vout: vout2: clktree_init
[ 5.914584] vout: vout2: register server: nulldisp_vout2_server
[ 5.920703] vout: vout2: init mode null set ok
[ 5.925244] vout: vout2: aml_vout2_probe OK
[ 5.929623] DI: di_module_init ok.
[ 5.933187] DI: di_probe:
[ 5.935903] DI: di_probe: major 510
[ 5.939635] deinterlace deinterlace: assigned reserved memory node linux,di_cma
[ 5.946999] di:flag_cma=1
[ 5.949766] DI: CMA size 0x2800000.
[ 5.953420] pre_irq:69
[ 5.955925] post_irq:70
[ 5.958524] DI: di_probe allocate rdma channel 0.
[ 5.963377] di_get_vpu_clkb: get clk vpu error.
[ 5.968057] DI: vpu clkb <334000000, 667000000>
[ 5.972749] get clkb rate:333333328
[ 5.976379] DI:enable vpu clkb.
[ 5.979673] 0x000000e1:Y=e1,U=0,V=0
[ 5.983308] 0x000000e2:Y=e2,U=0,V=0
[ 5.986949] 0x000000e3:Y=e3,U=0,V=0
[ 5.990587] 0x000000f0:Y=f0,U=0,V=0
[ 5.994228] 0x000000f1:Y=f1,U=0,V=0
[ 5.997866] 0x000000f2:Y=f2,U=0,V=0
[ 6.001508] 0x000000f3:Y=f3,U=0,V=0
[ 6.005149] 0x000000f4:Y=f4,U=0,V=0
[ 6.008788] 0x000000f5:Y=f5,U=0,V=0
[ 6.012428] 0x000000f6:Y=f6,U=0,V=0
[ 6.016069] 0x000000f7:Y=f7,U=0,V=0
[ 6.019708] 0x000000f8:Y=f8,U=0,V=0
[ 6.023347] 0x000000f9:Y=f9,U=0,V=0
[ 6.026988] 0x000000fa:Y=fa,U=0,V=0
[ 6.030628] 0x000000fb:Y=fb,U=0,V=0
[ 6.034268] 0x000000fc:Y=fc,U=0,V=0
[ 6.037907] 0x000000fd:Y=fd,U=0,V=0
[ 6.041548] 0x000000fe:Y=fe,U=0,V=0
[ 6.045188] 0x000000ff:Y=ff,U=0,V=0
[ 6.048827] 0x0000003a:Y=3a,U=0,V=0
[ 6.052468] 0x0000003b:Y=3b,U=0,V=0
[ 6.056108] 0x0000003c:Y=3c,U=0,V=0
[ 6.059748] 0x0000003d:Y=3d,U=0,V=0
[ 6.063388] 0x0000003e:Y=3e,U=0,V=0
[ 6.067028] 0x0000003f:Y=3f,U=0,V=0
[ 6.070669] DI: support multi decoding 61~62~63.
[ 6.075512] DI: di_probe:Di use HRTIMER
[ 6.079479] DI: di_probe:ok
[ 6.082393] dim:dim_module_init
[ 6.085751] dim:dim_module_init finish
[ 6.089565] dil:dil_init.
[ 6.092380] dil:dil_init ok.
[ 6.095380] vdin_drv_init: major 509
[ 6.099146] vdin_drv_init: vdin driver init done
[ 6.103863] [viuin..]viuin_init_module viuin module init
[ 6.109422] [viuin..]viuin_probe probe ok.
[ 6.113713] [RX]-hdmirx: hdmirx_init.
[ 6.117387] ESM HLD: Initializing...
[ 6.121323] amlvid:info: amlvideo_init called
[ 6.125454] amlvid:info: amlvideo_create_instance called
[ 6.130907] amlvid:info: v4l2_dev.name=:amlvideo-000
[ 6.136068] amlvideo-000: V4L2 device registered as video10
[ 6.141737] amlvid:info: amlvideo_create_instance called
[ 6.147199] amlvid:info: v4l2_dev.name=:amlvideo-001
[ 6.152348] amlvideo-001: V4L2 device registered as video23
[ 6.158077] PPMGRDRV: warn: ppmgr module init func called
[ 6.163615] PPMGRDRV: info: ppmgr_driver_probe called
[ 6.168809] Reserved memory: failed to init DMA memory pool at 0x000000006d800000, size 0 MiB
[ 6.177448] PPMGRDRV: info: ppmgr_dev major:507
[ 6.182329] ionvideo-000: V4L2 device registered as video13
[ 6.187886] ionvideo-001: V4L2 device registered as video14
[ 6.193607] ionvideo-002: V4L2 device registered as video15
[ 6.199322] ionvideo-003: V4L2 device registered as video16
[ 6.205042] ionvideo-004: V4L2 device registered as video17
[ 6.210760] ionvideo-005: V4L2 device registered as video18
[ 6.216481] ionvideo-006: V4L2 device registered as video19
[ 6.222199] ionvideo-007: V4L2 device registered as video20
[ 6.227921] ionvideo-008: V4L2 device registered as video21
[ 6.233604] ionvid: info: Video Technology Magazine Ion Video
[ 6.239499] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 6.246035] videosync_create_instance dev_s ffffffc052db4400,dev_s->dev ffffffc0542ead00
[ 6.254146] videosync_create_instance reg videosync.0
[ 6.259372] aml_vecm_init:module init
[ 6.259373] videosync_thread started
[ 6.266953]
VECM probe start
[ 6.271745] Can't find detect_colorbar.
[ 6.275727] Can't find detect_face.
[ 6.279450] Can't find detect_corn.
[ 6.283175] Can't find wb_sel.
[ 6.286474] hdr:Can't find cfg_en_osd_100.
[ 6.290804] Can't find tx_op_color_primary.
[ 6.295223] amlogic, vecm
[ 6.297823] vlock dt support: 1
[ 6.301115] vlock dt new_fsm: 0
[ 6.304409] vlock dt hwver: 0
[ 6.307531] vlock dt phlock_en: 0
[ 6.310996] Can't find vlock_en.
[ 6.314461] Can't find vlock_mode.
[ 6.318103] Can't find vlock_pll_m_limit.
[ 6.322348] Can't find vlock_line_limit.
[ 6.326518] param_config vlock_en:1 md=0x4
[ 6.330756] vlock: maxLine 524,maxPixel 1715
[ 6.335175] vlock_status_init vlock_en:1
[ 6.339254] aml_vecm_probe: ok
[ 6.342476] amdolby_vision_init:module init
[ 6.346871]
amdolby_vision probe start & ver: 20181220
[ 6.349644] hdmitx: hdmitx_set_drm_pkt: tf=1, cf=1, colormetry=0
[ 6.359967]
cpu_id=2 tvmode=0
[ 6.364864] dolby_vision_init_receiver(dvel)
[ 6.369240] dolby_vision_init_receiver: dvel
[ 6.373720] amdolby_vision_probe: ok
[ 6.377386] dovi disable in uboot
[ 6.380917] reg base = ffffff800872b000
[ 6.385267] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[ 6.393193] meson-mmc: >>>>>>>>hostbase ffffff8008733000, dmode
[ 6.399089] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 6.404685] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 6.450015] meson-mmc: meson_mmc_probe() : success!
[ 6.458546] meson-mmc: >>>>>>>>hostbase ffffff800873c000, dmode
[ 6.460951] meson-mmc: gpio_cd = 1ca
[ 6.502019] meson-mmc: meson_mmc_probe() : success!
[ 6.503768] cectx ff80023c.aocec: cec driver date:2019/10/22: finetune ARB rising time
[ 6.512460] cectx ff80023c.aocec: compatible:amlogic, aocec-g12a
[ 6.518399] cectx ff80023c.aocec: cecb_ver:0x1
[ 6.522917] cectx ff80023c.aocec: line_reg:0x1
[ 6.527493] cectx ff80023c.aocec: line_bit:0x3
[ 6.532128] cectx ff80023c.aocec: ee_to_ao:0x1
[ 6.536811] input: cec_input as /devices/virtual/input/input0
[ 6.542704] cectx ff80023c.aocec: not find 'port_num'
[ 6.547841] cectx ff80023c.aocec: using cec:1
[ 6.552317] cectx ff80023c.aocec: no hdmirx regs
[ 6.557035] cectx ff80023c.aocec: no hhi regs
[ 6.561545] cectx ff80023c.aocec: not find 'output'
[ 6.567823] irq cnt:2, a:44, b43
[ 6.570135] cectx ff80023c.aocec: wakeup_reason:0x0
[ 6.575193] cectx ff80023c.aocec: cev val1: 0x0;val2: 0x0
[ 6.580540] cectx ff80023c.aocec: aml_cec_probe success end
[ 6.586402] unifykey: storage in base: 0xffffffc005000000
[ 6.591810] unifykey: storage out base: 0xffffffc005040000
[ 6.591849] meson-aml-mmc ffe07000.emmc: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 6.591851] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 6.591852] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 6.591854] meson-mmc: Data 1 aligned delay is 0
[ 6.591856] meson-mmc: emmc: clk 199999997 tuning start
[ 6.630276] unifykey: storage block base: 0xffffffc005080000
[ 6.636079] unifykey: probe done!
[ 6.639709] unifykey: aml_unifykeys_init done!
[ 6.644164] meson ts init
[ 6.646936] tsensor id: 0
[ 6.649733] r1p1_tsensor_read valid cnt is 0
[ 6.654208] tsensor trim info: 0xfa00801d!
[ 6.658445] tsensor hireboot: 0xc0ff2a90
[ 6.662570] meson ts init
[ 6.665292] tsensor id: 1
[ 6.668091] r1p1_tsensor_read valid cnt is 0
[ 6.672571] tsensor trim info: 0xfa008059!
[ 6.676814] tsensor hireboot: 0xc0ff2aa0
[ 6.680961] audio_dsp: [dsp]register dsp to char divece(257)
[ 6.686773] amaudio: amaudio: driver amaudio init!
[ 6.691781] amaudio: amaudio_init - amaudio: driver amaudio succuess!
[ 6.698456] amlkaraoke init success!
[ 6.701989] sysled: module init
[ 6.705335] meson_wdt ffd0f0d0.watchdog: start watchdog
[ 6.710616] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[ 6.717468] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[ 6.724343] amlogic rfkill init
[ 6.727608] meson-saradc ff809000.saradc: set delay per tick to <1ms> by default.
[ 6.735061] meson-saradc ff809000.saradc: set ticks per period to <1> by default.
[ 6.743191] dmc_monitor_probe
[ 6.746333] atv_demod: aml_atvdemod_init: OK, atv demod version: V2.15.
[ 6.752611] defendkey ff630218.defendkey: Reserved memory is not enough!
[ 6.759415] defendkey: probe of ff630218.defendkey failed with error -22
[ 6.766543] usbcore: registered new interface driver snd-usb-audio
[ 6.773114] meson-mmc: emmc: adj_win: < 0 2 3 4 >
[ 6.773246] aml_codec_T9015 ff632000.t9015: aml_T9015_audio_codec_probe
[ 6.773254] T9015 acodec used by auge, tdmout:2
[ 6.773703] Error: Driver 'spdif-dit' is already registered, aborting...
[ 6.773836] asoc debug: aml_audio_controller_probe-130
[ 6.773972] aml_tdm_platform_probe, tdm ID = 2, lane_cnt = 4
[ 6.773978] TDM id 2 i2s2hdmi:0
[ 6.773982] snd_tdm ff642000.audiobus:tdmc: lane_mask_out = 1, lane_oe_mask_out = 0
[ 6.774063] snd_tdm ff642000.audiobus:tdmc: neither mclk_pad nor mclk2pad set
[ 6.774067] snd_tdm ff642000.audiobus:tdmc: aml_tdm_get_pins error!
[ 6.774070] aml_tdm_platform_probe(), share en = 1
[ 6.774070] No channel mask node Channel_Mask
[ 6.774247] aml_spdif_platform_probe, spdif ID = 1
[ 6.774280] spdifout_play_with_zerodata, spdif id:1 enable:0
[ 6.774282] spdif_b fifo ctrl, frddr:0 type:3, 32 bits, chmask 0x3, swap 0x10
[ 6.774285] spdif_info: rate: 48000, channel status ch0_l:0x100, ch0_r:0x100, ch1_l:0x200, ch1_r:0x200
[ 6.774289] hdmitx: audio: aout notify format CT_PCM
[ 6.774290] hdmitx: hw: set audio
[ 6.774291] hdmitx: hw: hdmitx tx_aud_src = 0
[ 6.774301] hdmitx: fs = 3, cd = 4, tmds_clk = 148500
[ 6.774302] hdmitx: hw: aud_n_para = 6144
[ 6.774308] hdmitx: hw: set channel status
[ 6.774335] hdmitx: audio: Audio Type: PCM
[ 6.774336] hdmitx: audio: set audio param
[ 6.774338] spdif_b is set to enable
[ 6.774342] aml_spdif_platform_probe, register soc platform
[ 6.774532] audio-ddr-manager ff642000.audiobus:ddr_manager: 0, irqs toddr 33, frddr 36
[ 6.774538] audio-ddr-manager ff642000.audiobus:ddr_manager: 1, irqs toddr 34, frddr 37
[ 6.774544] audio-ddr-manager ff642000.audiobus:ddr_manager: 2, irqs toddr 35, frddr 38
[ 6.774731] audiolocker_platform_probe
[ 6.775230] Register vad
[ 6.775413] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.775415] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.775416] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.775417] aml_card_probe error ret:-517
[ 6.775463] Netfilter messages via NETLINK v0.30.
[ 6.775517] Initializing XFRM netlink socket
[ 6.775524] NET: Registered protocol family 17
[ 6.775538] Key type dns_resolver registered
[ 6.775688] Registered swp emulation handler
[ 6.777425] Registered cp15_barrier emulation handler
[ 6.777442] Registered setend emulation handler
[ 6.777651] registered taskstats version 1
[ 6.786654] Key type big_key registered
[ 6.793637] Key type encrypted registered
[ 6.793642] AppArmor: AppArmor sha1 policy hashing enabled
[ 6.796376] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.796378] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.796380] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.796381] aml_card_probe error ret:-517
[ 6.801051] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[ 6.803646] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.803654] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 6.803801] usb: xhci: determined sg_tablesize: 4294967295
[ 6.803802] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe6c hci version 0x110 quirks 0x20010010
[ 6.803820] xhci-hcd xhci-hcd.0.auto: irq 22, io mem 0xff500000
[ 6.803872] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 6.803874] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.803876] usb usb1: Product: xHCI Host Controller
[ 6.803877] usb usb1: Manufacturer: Linux 4.9.333-25 xhci-hcd
[ 6.803878] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 6.804074] hub 1-0:1.0: USB hub found
[ 6.804085] hub 1-0:1.0: 2 ports detected
[ 6.804414] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.804415] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.804417] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.804418] aml_card_probe error ret:-517
[ 6.804637] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.804638] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.804639] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.804640] aml_card_probe error ret:-517
[ 6.804666] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 6.804670] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 6.804691] usb: xhci: determined sg_tablesize: 4294967295
[ 6.804691] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 6.804718] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 6.804719] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 6.804721] usb usb2: Product: xHCI Host Controller
[ 6.804722] usb usb2: Manufacturer: Linux 4.9.333-25 xhci-hcd
[ 6.804723] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 6.804883] hub 2-0:1.0: USB hub found
[ 6.804890] hub 2-0:1.0: 1 port detected
[ 6.805103] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.805104] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.805106] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.805106] aml_card_probe error ret:-517
[ 6.805287] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.805289] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.805290] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.805291] aml_card_probe error ret:-517
[ 6.805472] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.805473] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.805475] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.805475] aml_card_probe error ret:-517
[ 6.805645] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.805647] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.805648] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.805649] aml_card_probe error ret:-517
[ 6.805748] hctosys: unable to open rtc device (rtc0)
[ 6.805873] dwc_otg ff400000.dwc2_a: dwc_otg_driver_probe(ffffffc056d8f000)
[ 6.805885] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[ 6.805890] dwc_otg ff400000.dwc2_a: base=0xffffff8008a40000
[ 6.805891] dwc_otg ff400000.dwc2_a: dwc_otg_device=0xffffffc053e93400
[ 6.905982] dwc_otg: Core Release: 3.30a
[ 6.905984] dwc_otg: Setting default values for core params
[ 6.905991] dwc_otg: curmode: 0, host_only: 0
[ 6.906005] dwc_otg ff400000.dwc2_a: DMA config: BURST_DEFAULT
[ 6.918123] dwc_otg: Using Buffer DMA mode
[ 6.918125] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 6.918126] dwc_otg: Working on port type = SLAVE
[ 6.918128] dwc_otg: Dedicated Tx FIFOs mode
[ 6.919060] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.919061] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.919063] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.919064] aml_card_probe error ret:-517
[ 6.919356] meson_cdev probe
[ 6.919381] meson_cdev index: 0
[ 6.919448] meson_cdev index: 1
[ 6.919484] thermal: no cluster id, cpucore as one cooldev
[ 6.919493] meson_cdev index: 2
[ 6.919495] cpucore_cooling_register, max_cpu_core_num:6
[ 6.919496] cpucore_cooling_register, clutser[1] core num:4
[ 6.919497] cpucore_cooling_register, clutser[0] core num:2
[ 6.919536] meson_cdev index: 3
[ 6.919545] meson_cdev index: 4
[ 6.919563] find tzd id: 0
[ 6.919630] find tzd id: 0
[ 6.919689] find tzd id: 0
[ 6.919721] meson_cdev probe done
[ 6.919942] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.919944] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.919945] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.919946] aml_card_probe error ret:-517
[ 6.919998] gxbb_pm: enter meson_pm_probe!
[ 6.920003] no vddio3v3_en pin
[ 6.920004] pm-meson aml_pm: Can't get switch_clk81
[ 6.920015] gxbb_pm: meson_pm_probe done
[ 6.920191] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6.920192] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6.920194] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6.920194] aml_card_probe error ret:-517
[ 6.920332] ALSA device list:
[ 6.920333] No soundcards found.
[ 7.314020] usb 1-2: new high-speed USB device number 2 using xhci-hcd
[ 7.395277] DI: DI: tasklet schedule cost 12ms.
[ 7.460278] usb 1-2: New USB device found, idVendor=05e3, idProduct=0610
[ 7.460281] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 7.460283] usb 1-2: Product: USB2.1 Hub
[ 7.460285] usb 1-2: Manufacturer: GenesysLogic
[ 7.476973] hub 1-2:1.0: USB hub found
[ 7.477232] hub 1-2:1.0: 4 ports detected
[ 7.479020] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 7.479022] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 7.479025] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 7.479026] aml_card_probe error ret:-517
[ 7.614891] meson-mmc: step:4, delay1:0x4104104, delay2:0x4004104
[ 7.621191] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 7.626345] Freeing unused kernel memory: 4992K
[ 7.630031] meson-mmc: emmc: adj_win: < 0 2 3 4 >
[ 7.633609] meson-mmc: step:8, delay1:0x8208208, delay2:0x8008208
[ 7.643319] meson-mmc: emmc: adj_win: < 0 2 3 4 >
[ 7.646900] meson-mmc: step:12, delay1:0xc30c30c, delay2:0xc00c30c
[ 7.656483] meson-mmc: emmc: adj_win: < 0 1 2 3 4 >
[ 7.661006] meson-mmc: step:16, delay1:0x10410410, delay2:0x10010410
[ 7.670155] meson-mmc: emmc: adj_win: < 0 1 3 4 >
[ 7.672346] meson-mmc: left:3, right:0, mid:4, size:4
[ 7.677593] meson-mmc: step:0, delay1:0x0, delay2:0x0
[ 7.682756] meson-mmc: emmc: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x42000
[ 7.691190] meson-mmc: delay1:0x0, delay2:0x0
[ 7.695834] emmc: new HS200 MMC card at address 0001
[ 7.700792] emmc: clock 199999997, 8-bit-bus-width
[ 7.706218] mmcblk0: emmc:0001 AJTD4R 14.6 GiB
[ 7.710658] mmcblk0boot0: emmc:0001 AJTD4R partition 1 4.00 MiB
[ 7.716719] mmcblk0boot1: emmc:0001 AJTD4R partition 2 4.00 MiB
[ 7.722792] mmcblk0rpmb: emmc:0001 AJTD4R partition 3 4.00 MiB
[ 7.729158] mmcblk0: p1 p2
[ 7.732789] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 7.741634] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 7.747332] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 7.756083] aml_card_probe error ret:-517
[ 7.794069] usb 1-2.1: new high-speed USB device number 3 using xhci-hcd
[ 7.918632] usb 1-2.1: New USB device found, idVendor=0bda, idProduct=8153
[ 7.920038] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 7.927535] usb 1-2.1: Product: USB 10/100/1000 LAN
[ 7.932539] usb 1-2.1: Manufacturer: Realtek
[ 7.936992] usb 1-2.1: SerialNumber: 000001
[ 7.957006] usb 1-2.1: Unsupported device
[ 7.957131] usb 1-2.1: Unsupported device
[ 7.960346] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 7.969949] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 7.970161] usbcore: registered new interface driver r8152
[ 7.971961] usbcore: registered new interface driver cdc_ether
[ 7.987179] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 7.995896] aml_card_probe error ret:-517
[ 8.071622] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 8.148722] usb 1-2.1: reset high-speed USB device number 3 using xhci-hcd
[ 8.249405] systemd[1]: System time before build time, advancing clock.
[ 8.299135] NET: Registered protocol family 10
[ 8.306905] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 8.307896] cgroup: cgroup2: unknown option "nsdelegate,memory_recursiveprot"
[ 8.314207] cgroup: cgroup2: unknown option "nsdelegate"
[ 8.318746] r8152 1-2.1:1.0 eth0: v2.10.00 (2018/03/16)
[ 8.318749] r8152 1-2.1:1.0 eth0: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 8.319387] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 8.319389] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 8.319392] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 8.319393] aml_card_probe error ret:-517
[ 8.386042] systemd[1]: systemd 249.11-0ubuntu3.6 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT +GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY -P11KIT -QRENCODE +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[ 8.412159] systemd[1]: Detected architecture arm64.
[ 8.434335] systemd[1]: Hostname set to <nl>.
[ 8.439257] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 8.638236] systemd[1]: Queued start job for default target Graphical Interface.
[ 8.641580] systemd[1]: Created slice Slice /system/modprobe.
[ 8.666420] systemd[1]: Created slice Slice /system/serial-getty.
[ 8.686269] systemd[1]: Created slice User and Session Slice.
[ 8.706453] systemd[1]: Started ntp-systemd-netif.path.
[ 8.722300] systemd[1]: Started Dispatch Password Requests to Console Directory Watch.
[ 8.742268] systemd[1]: Started Forward Password Requests to Wall Directory Watch.
[ 8.763225] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 8.786217] systemd[1]: Reached target Local Encrypted Volumes.
[ 8.806224] systemd[1]: Reached target Path Units.
[ 8.822121] systemd[1]: Reached target Remote File Systems.
[ 8.842120] systemd[1]: Reached target Slice Units.
[ 8.858131] systemd[1]: Reached target Swaps.
[ 8.874150] systemd[1]: Reached target Local Verity Protected Volumes.
[ 8.894768] systemd[1]: Listening on Syslog Socket.
[ 8.910531] systemd[1]: Listening on fsck to fsckd communication Socket.
[ 8.930297] systemd[1]: Listening on initctl Compatibility Named Pipe.
[ 8.950683] systemd[1]: Listening on Journal Audit Socket.
[ 8.970445] systemd[1]: Listening on Journal Socket (/dev/log).
[ 8.990508] systemd[1]: Listening on Journal Socket.
[ 9.006916] systemd[1]: Listening on udev Control Socket.
[ 9.026444] systemd[1]: Listening on udev Kernel Socket.
[ 9.042147] systemd[1]: Reached target Socket Units.
[ 9.058431] systemd[1]: Condition check resulted in Huge Pages File System being skipped.
[ 9.063591] systemd[1]: Mounting POSIX Message Queue File System...
[ 9.088162] systemd[1]: Mounting Kernel Debug File System...
[ 9.111983] systemd[1]: Mounting Kernel Trace File System...
[ 9.128773] systemd[1]: Starting Set the console keyboard layout...
[ 9.152791] systemd[1]: Starting Create List of Static Device Nodes...
[ 9.176831] systemd[1]: Starting Load Kernel Module chromeos_pstore...
[ 9.200608] systemd[1]: Starting Load Kernel Module configfs...
[ 9.220480] systemd[1]: Starting Load Kernel Module drm...
[ 9.239463] systemd[1]: Starting Load Kernel Module efi_pstore...
[ 9.260526] systemd[1]: Starting Load Kernel Module fuse...
[ 9.273527] fuse init (API version 7.26)
[ 9.280594] systemd[1]: Starting Load Kernel Module pstore_blk...
[ 9.300593] systemd[1]: Starting Load Kernel Module pstore_zone...
[ 9.320579] systemd[1]: Starting Load Kernel Module ramoops...
[ 9.338449] systemd[1]: Condition check resulted in File System Check on Root Device being skipped.
[ 9.345457] systemd[1]: Starting Load Kernel Modules...
[ 9.362947] No find node.
[ 9.362971] register clk_set_setting cpu[41]
[ 9.364407] systemd[1]: Starting Remount Root and Kernel File Systems...
[ 9.373894] Registered firmware driver success.
[ 9.377326] Try to load video/h264_enc.bin ...
[ 9.378081] EXT4-fs (mmcblk0p2): re-mounted. Opts: errors=remount-ro
[ 9.389288] load firmware size : 76288, Name : video/h264_enc.bin.
[ 9.394235] Try to load video/video_ucode.bin ...
[ 9.411118] load firmware size : 1816576, Name : video/video_ucode.bin.
[ 9.422180] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 9.424507] systemd[1]: Starting Coldplug All udev Devices...
[ 9.432943] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 9.432945] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 9.432946] aml_card_probe error ret:-517
[ 9.456304] Amlogic A/V streaming port init
[ 9.459249] get gate demux control ok ffffffc0492e9a00
[ 9.463740] get gate parser_top control ok ffffffc0492e9a80
[ 9.469484] get gate vdec control ok ffffffc0492e9b00
[ 9.474648] get gate clk_81 control failed (null)
[ 9.480380] get gate clk_vdec_mux control ok ffffffc0492e9b80
[ 9.486275] get gate clk_hcodec_mux control ok ffffffc0492e9c00
[ 9.492340] get gate clk_hevc_mux control ok ffffffc0492e9c80
[ 9.498238] get gate clk_hevcb_mux control ok ffffffc0492e9d00
[ 9.504197] get gate ahbarb0 control ok ffffffc0492e9d80
[ 9.509672] get gate asyncfifo control failed (null)
[ 9.516015] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 9.525712] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 9.531432] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 9.540171] aml_card_probe error ret:-517
[ 9.540733] amvdec_avs module init
[ 9.546184] amvdec_h264 module init
[ 9.550746] ammvdec_h264 module init
[ 9.556315] amvdec_h265 module init
[ 9.563326] ammvdec_mpeg4_driver_init_module
[ 9.565671] amvdec_vc1 module init
[ 9.567857] systemd[1]: Mounted POSIX Message Queue File System.
[ 9.569275] amvdec_vp9 module init
[ 9.586779] systemd[1]: Mounted Kernel Debug File System.
[ 9.606600] systemd[1]: Mounted Kernel Trace File System.
[ 9.626917] systemd[1]: Finished Set the console keyboard layout.
[ 9.658729] systemd[1]: Finished Create List of Static Device Nodes.
[ 9.690710] systemd[1]: modprobe@chromeos_pstore.service: Deactivated successfully.
[ 9.693245] systemd[1]: Finished Load Kernel Module chromeos_pstore.
[ 9.726660] systemd[1]: modprobe@configfs.service: Deactivated successfully.
[ 9.728592] systemd[1]: Finished Load Kernel Module configfs.
[ 9.762659] systemd[1]: modprobe@drm.service: Deactivated successfully.
[ 9.764158] systemd[1]: Finished Load Kernel Module drm.
[ 9.794673] systemd[1]: modprobe@efi_pstore.service: Deactivated successfully.
[ 9.796810] systemd[1]: Finished Load Kernel Module efi_pstore.
[ 9.830664] systemd[1]: modprobe@fuse.service: Deactivated successfully.
[ 9.832246] systemd[1]: Finished Load Kernel Module fuse.
[ 9.862696] systemd[1]: modprobe@pstore_blk.service: Deactivated successfully.
[ 9.864796] systemd[1]: Finished Load Kernel Module pstore_blk.
[ 9.906693] systemd[1]: modprobe@pstore_zone.service: Deactivated successfully.
[ 9.908882] systemd[1]: Finished Load Kernel Module pstore_zone.
[ 9.942674] systemd[1]: modprobe@ramoops.service: Deactivated successfully.
[ 9.944519] systemd[1]: Finished Load Kernel Module ramoops.
[ 9.978670] systemd[1]: Finished Load Kernel Modules.
[ 9.994976] systemd[1]: Finished Remount Root and Kernel File Systems.
[ 10.039377] systemd[1]: Mounting FUSE Control File System...
[ 10.056395] systemd[1]: Mounting Kernel Configuration File System...
[ 10.076398] systemd[1]: Starting Synchronise System clock to hardware RTC...
[ 10.099415] systemd[1]: Starting Initialize pwm-ctrl driver and set duty. frequency, and state...
[ 10.101753] meson-pwm ff802000.pwm: pwm pinmux : can't get pinctrl
[ 10.128063] systemd[1]: Starting Initialize i2c hardware RTC device driver...
[ 10.150199] systemd[1]: Condition check resulted in Platform Persistent Storage Archival being skipped.
[ 10.155544] systemd[1]: Starting Load/Save Random Seed...
[ 10.179281] systemd[1]: Starting Apply Kernel Variables...
[ 10.196381] systemd[1]: Starting Create System Users...
[ 10.210454] systemd[1]: Finished Coldplug All udev Devices.
[ 10.238548] systemd[1]: Mounted FUSE Control File System.
[ 10.250639] systemd[1]: Mounted Kernel Configuration File System.
[ 10.262635] systemd[1]: hwrtc.service: Main process exited, code=exited, status=1/FAILURE
[ 10.262923] systemd[1]: hwrtc.service: Failed with result 'exit-code'.
[ 10.263272] systemd[1]: Failed to start Synchronise System clock to hardware RTC.
[ 10.295106] systemd[1]: Finished Initialize pwm-ctrl driver and set duty. frequency, and state.
[ 10.326374] systemd[1]: rtc-i2c.service: Main process exited, code=exited, status=2/INVALIDARGUMENT
[ 10.326672] systemd[1]: rtc-i2c.service: Failed with result 'exit-code'.
[ 10.327019] systemd[1]: Failed to start Initialize i2c hardware RTC device driver.
[ 10.359130] systemd[1]: Finished Load/Save Random Seed.
[ 10.390719] systemd[1]: Finished Apply Kernel Variables.
[ 10.406941] systemd[1]: Condition check resulted in First Boot Complete being skipped.
[ 10.420262] systemd[1]: Starting Journal Service...
[ 10.431074] systemd[1]: Finished Create System Users.
[ 10.443731] systemd[1]: Starting Create Static Device Nodes in /dev...
[ 10.478529] systemd[1]: Finished Create Static Device Nodes in /dev.
[ 10.490374] systemd[1]: Reached target Preparation for Local File Systems.
[ 10.503354] systemd[1]: Starting Rule-based Manager for Device Events and Files...
[ 10.538350] systemd[1]: Started Journal Service.
[ 10.570605] systemd-journald[2879]: Received client request to flush runtime journal.
[ 10.571696] systemd-journald[2879]: File /var/log/journal/e00bd6223a7245d0aa6e19e0ab12a024/system.journal corrupted or uncleanly shut down, renaming and replacing.
[ 10.942931] Driver for 1-wire Dallas network protocol.
[ 10.945750] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 10.950473] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 10.956305] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 10.965110] aml_card_probe error ret:-517
[ 10.970685] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 10.979320] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 10.986177] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 10.987079] rtc-pcf8563 0-0051: pcf8563_write_block_data: err=-6 addr=0e, data=03
[ 10.987081] rtc-pcf8563 0-0051: pcf8563_probe: write error
[ 10.987094] rtc-pcf8563: probe of 0-0051 failed with error -5
[ 10.987682] rtc-pcf8563 1-0051: pcf8563_write_block_data: err=-6 addr=0e, data=03
[ 10.987684] rtc-pcf8563 1-0051: pcf8563_probe: write error
[ 10.987696] rtc-pcf8563: probe of 1-0051 failed with error -5
[ 11.020472] aml_card_probe error ret:-517
[ 11.025678] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 11.034505] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 11.040731] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 11.049752] aml_card_probe error ret:-517
[ 11.136442] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 11.211503] ionvid: dbg: ionvideo open
[ 11.211569] ionvid: dbg: vidioc_close!!!!
[ 11.211574] ionvid: dbg: vidioc_close
[ 11.211647] ionvid: dbg: ionvideo open
[ 11.211693] ionvid: dbg: vidioc_close!!!!
[ 11.211697] ionvid: dbg: vidioc_close
[ 11.212290] ionvid: dbg: ionvideo open
[ 11.212355] ionvid: dbg: vidioc_close!!!!
[ 11.212360] ionvid: dbg: vidioc_close
[ 11.213515] ionvid: dbg: ionvideo open
[ 11.213515] ionvid: dbg: ionvideo open
[ 11.213579] ionvid: dbg: vidioc_close!!!!
[ 11.213580] ionvid: dbg: vidioc_close!!!!
[ 11.213584] ionvid: dbg: vidioc_close
[ 11.213585] ionvid: dbg: vidioc_close
[ 11.214442] ionvid: dbg: ionvideo open
[ 11.214563] ionvid: dbg: vidioc_close!!!!
[ 11.214572] ionvid: dbg: vidioc_close
[ 11.216118] ionvid: dbg: ionvideo open
[ 11.216190] ionvid: dbg: vidioc_close!!!!
[ 11.216195] ionvid: dbg: vidioc_close
[ 11.217154] ionvid: dbg: ionvideo open
[ 11.217221] ionvid: dbg: vidioc_close!!!!
[ 11.217225] ionvid: dbg: vidioc_close
[ 11.220748] usb 1-2.1: reset high-speed USB device number 3 using xhci-hcd
[ 11.221058] ionvid: dbg: ionvideo open
[ 11.221130] ionvid: dbg: vidioc_close!!!!
[ 11.221136] ionvid: dbg: vidioc_close
[ 11.430030] vout: aml_tvout_mode_work: monitor_timeout
[ 11.431027] r8152 1-2.1:1.0 eth0: v2.10.00 (2018/03/16)
[ 11.431033] r8152 1-2.1:1.0 eth0: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 11.434219] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 11.445643] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 11.447694] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 11.456395] aml_card_probe error ret:-517
[ 11.510802] i2c i2c-1: Failed to register i2c client pcf8563 at 0x51 (-16)
[ 12.243960] gpiomem-aml ff634000.gpiomem: gpiomem device opened.
[ 12.958631] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 12.963207] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 13.862753] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 15.061296] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 15.062334] r8152 1-2.1:1.0 eth0: carrier on
[ 17.377320] systemd-journald[2879]: File /var/log/journal/e00bd6223a7245d0aa6e19e0ab12a024/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
Code: Select all
[ 17.377320] systemd-journald[2879]: File /var/log/journal/e00bd6223a7245d0aa6e19e0ab12a024/user-1000.journal corrupted or uncleanly shut down, renaming and replacing.
[ 66.563574] fb: mem_free_work, free memory: addr:800000
[ 615.564580] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 615.599650] usb 2-1: New USB device found, idVendor=05e3, idProduct=0626
[ 615.599652] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 615.599654] usb 2-1: Product: USB3.1 Hub
[ 615.599655] usb 2-1: Manufacturer: GenesysLogic
[ 615.607313] hub 2-1:1.0: USB hub found
[ 615.608689] hub 2-1:1.0: 4 ports detected
[ 615.613863] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 615.618311] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 615.624044] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 615.632780] aml_card_probe error ret:-517
[ 615.708056] usb 1-1: new high-speed USB device number 4 using xhci-hcd
[ 615.864143] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610
[ 615.864145] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 615.864146] usb 1-1: Product: USB2.1 Hub
[ 615.864148] usb 1-1: Manufacturer: GenesysLogic
[ 615.893528] hub 1-1:1.0: USB hub found
[ 615.895264] hub 1-1:1.0: 4 ports detected
[ 615.903455] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 615.907894] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 615.913692] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 615.922413] aml_card_probe error ret:-517
[ 615.936082] usb 2-1.4: new SuperSpeed USB device number 3 using xhci-hcd
[ 615.956582] usb 2-1.4: New USB device found, idVendor=0bda, idProduct=8153
[ 615.956585] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 615.956586] usb 2-1.4: Product: USB 10/100/1000 LAN
[ 615.956587] usb 2-1.4: Manufacturer: Realtek
[ 615.956588] usb 2-1.4: SerialNumber: 000001
[ 615.972996] usb 2-1.4: Unsupported device
[ 615.973058] usb 2-1.4: Unsupported device
[ 615.976089] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 615.985790] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 615.991589] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 616.000272] aml_card_probe error ret:-517
[ 616.116731] usb 2-1.4: reset SuperSpeed USB device number 3 using xhci-hcd
[ 616.194839] r8152 2-1.4:1.0 eth1: v2.10.00 (2018/03/16)
[ 616.194844] r8152 2-1.4:1.0 eth1: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
This is dmesg after plugging the ethernet cable back into the Aceele adapter and reconnecting via ssh:
Code: Select all
[ 616.194844] r8152 2-1.4:1.0 eth1: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 616.195271] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 616.199747] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 616.205447] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 616.214264] aml_card_probe error ret:-517
[ 616.372757] usb 2-1.4: reset SuperSpeed USB device number 3 using xhci-hcd
[ 616.392245] usb 2-1.4: device firmware changed
[ 616.393813] usb 2-1.4: USB disconnect, device number 3
[ 658.394222] r8152 2-1.4:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
[ 658.403672] r8152 2-1.4:1.0 eth1: v2.10.00 (2018/03/16)
[ 658.403678] r8152 2-1.4:1.0 eth1: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 658.412838] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 658.417403] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 658.423051] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 658.431841] aml_card_probe error ret:-517
[ 914.776773] r8152 1-2.1:1.0 eth0: carrier off
[ 1032.086205] r8152 1-2.1:1.0 eth0: carrier on
Code: Select all
[ 1032.086205] r8152 1-2.1:1.0 eth0: carrier on
[ 1428.632781] usb 2-1: USB disconnect, device number 2
[ 1428.884447] usb 1-1: USB disconnect, device number 4
[ 1455.877445] r8152 1-2.1:1.0 eth0: Rx status -71
[ 1455.877485] r8152 1-2.1:1.0 eth0: Rx status -71
[ 1455.877567] r8152 1-2.1:1.0 eth0: Rx status -71
[ 1455.877605] r8152 1-2.1:1.0 eth0: Rx status -71
[ 1455.877688] r8152 1-2.1:1.0 eth0: Rx status -71
[ 1455.877733] r8152 1-2.1:1.0 eth0: Rx status -71
[ 1455.877821] usb 1-2: USB disconnect, device number 2
[ 1455.877824] usb 1-2.1: USB disconnect, device number 3
[ 1455.877848] r8152 1-2.1:1.0 eth0: Rx status -71
[ 1459.649206] usb 2-1: new SuperSpeed USB device number 5 using xhci-hcd
[ 1459.678080] usb 2-1: New USB device found, idVendor=05e3, idProduct=0626
[ 1459.678082] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1459.678083] usb 2-1: Product: USB3.1 Hub
[ 1459.678085] usb 2-1: Manufacturer: GenesysLogic
[ 1459.685564] hub 2-1:1.0: USB hub found
[ 1459.686342] hub 2-1:1.0: 4 ports detected
[ 1459.687821] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1459.692274] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1459.698001] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1459.706750] aml_card_probe error ret:-517
[ 1459.789097] usb 1-1: new high-speed USB device number 5 using xhci-hcd
[ 1459.931828] usb 1-1: New USB device found, idVendor=05e3, idProduct=0610
[ 1459.931831] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1459.931832] usb 1-1: Product: USB2.1 Hub
[ 1459.931833] usb 1-1: Manufacturer: GenesysLogic
[ 1459.956872] hub 1-1:1.0: USB hub found
[ 1459.957103] hub 1-1:1.0: 4 ports detected
[ 1459.958485] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1459.962932] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1459.968656] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1459.977465] aml_card_probe error ret:-517
[ 1460.009126] usb 2-1.1: new SuperSpeed USB device number 6 using xhci-hcd
[ 1460.029603] usb 2-1.1: New USB device found, idVendor=0bda, idProduct=8153
[ 1460.029605] usb 2-1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 1460.029607] usb 2-1.1: Product: USB 10/100/1000 LAN
[ 1460.029608] usb 2-1.1: Manufacturer: Realtek
[ 1460.029609] usb 2-1.1: SerialNumber: 000001
[ 1460.036968] usb 2-1.1: Unsupported device
[ 1460.037030] usb 2-1.1: Unsupported device
[ 1460.040073] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1460.049779] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1460.055495] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1460.064210] aml_card_probe error ret:-517
[ 1460.164724] usb 2-1.1: reset SuperSpeed USB device number 6 using xhci-hcd
[ 1460.243690] r8152 2-1.1:1.0 eth0: v2.10.00 (2018/03/16)
[ 1460.243695] r8152 2-1.1:1.0 eth0: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 1460.244118] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1460.248654] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1460.254387] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1460.263061] aml_card_probe error ret:-517
[ 1460.420753] usb 2-1.1: reset SuperSpeed USB device number 6 using xhci-hcd
[ 1460.437286] usb 2-1.1: device firmware changed
[ 1460.437702] usb 2-1.1: USB disconnect, device number 6
[ 1494.017200] usb 1-1: USB disconnect, device number 5
[ 1498.699473] usb 1-2: new high-speed USB device number 6 using xhci-hcd
[ 1498.841715] usb 1-2: New USB device found, idVendor=05e3, idProduct=0610
[ 1498.841717] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1498.841719] usb 1-2: Product: USB2.1 Hub
[ 1498.841720] usb 1-2: Manufacturer: GenesysLogic
[ 1498.868858] hub 1-2:1.0: USB hub found
[ 1498.869155] hub 1-2:1.0: 4 ports detected
[ 1498.870565] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1498.875015] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1498.880744] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1498.889566] aml_card_probe error ret:-517
[ 1499.179451] usb 1-2.1: new high-speed USB device number 7 using xhci-hcd
[ 1499.303918] usb 1-2.1: New USB device found, idVendor=0bda, idProduct=8153
[ 1499.303920] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 1499.303921] usb 1-2.1: Product: USB 10/100/1000 LAN
[ 1499.303923] usb 1-2.1: Manufacturer: Realtek
[ 1499.303924] usb 1-2.1: SerialNumber: 000001
[ 1499.316966] usb 1-2.1: Unsupported device
[ 1499.317030] usb 1-2.1: Unsupported device
[ 1499.320091] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1499.329847] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1499.335504] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1499.344207] aml_card_probe error ret:-517
[ 1499.508677] usb 1-2.1: reset high-speed USB device number 7 using xhci-hcd
[ 1499.681896] r8152 1-2.1:1.0 eth0: v2.10.00 (2018/03/16)
[ 1499.681901] r8152 1-2.1:1.0 eth0: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 1499.682305] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1499.686871] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1499.692568] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1499.701250] aml_card_probe error ret:-517
[ 1499.892701] usb 1-2.1: reset high-speed USB device number 7 using xhci-hcd
[ 1500.070762] r8152 1-2.1:1.0 eth0: v2.10.00 (2018/03/16)
[ 1500.070768] r8152 1-2.1:1.0 eth0: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 1500.075359] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1500.081847] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1500.085879] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1500.094496] aml_card_probe error ret:-517
[ 1500.145546] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1500.153757] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 1502.447335] r8152 2-1.1:1.0 (unnamed net_device) (uninitialized): Get ether addr fail
[ 1502.450876] r8152 2-1.1:1.0 eth1: v2.10.00 (2018/03/16)
[ 1502.450882] r8152 2-1.1:1.0 eth1: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 1502.453544] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1502.464765] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1502.465468] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1502.474395] aml_card_probe error ret:-517
[ 1502.495645] hub 2-1:1.0: hub_ext_port_status failed (err = -71)
[ 1502.496144] usb 2-1-port1: cannot reset (err = -71)
[ 1502.501193] usb 2-1-port1: cannot reset (err = -71)
[ 1502.506226] usb 2-1-port1: cannot reset (err = -71)
[ 1502.511323] usb 2-1-port1: cannot reset (err = -71)
[ 1502.522591] usb 2-1-port1: cannot reset (err = -71)
[ 1502.522612] usb 2-1-port1: Cannot enable. Maybe the USB cable is bad?
[ 1502.528756] hub 2-1:1.0: hub_ext_port_status failed (err = -71)
[ 1502.534730] usb 2-1-port1: cannot reset (err = -71)
[ 1502.539738] usb 2-1-port1: cannot reset (err = -71)
[ 1502.544761] usb 2-1-port1: cannot reset (err = -71)
[ 1502.549809] usb 2-1-port1: cannot reset (err = -71)
[ 1502.554820] usb 2-1-port1: cannot reset (err = -71)
[ 1502.559799] usb 2-1-port1: Cannot enable. Maybe the USB cable is bad?
[ 1502.566404] usb 2-1-port1: attempt power cycle
[ 1502.879359] hub 2-1:1.0: hub_ext_port_status failed (err = -71)
[ 1502.879851] usb 2-1-port1: cannot reset (err = -71)
[ 1502.884903] usb 2-1-port1: cannot reset (err = -71)
[ 1502.889931] usb 2-1-port1: cannot reset (err = -71)
[ 1502.894947] usb 2-1-port1: cannot reset (err = -71)
[ 1502.899975] usb 2-1-port1: cannot reset (err = -71)
[ 1502.904965] usb 2-1-port1: Cannot enable. Maybe the USB cable is bad?
[ 1502.911591] hub 2-1:1.0: hub_ext_port_status failed (err = -71)
[ 1502.917649] usb 2-1-port1: cannot reset (err = -71)
[ 1502.922681] usb 2-1-port1: cannot reset (err = -71)
[ 1502.927697] usb 2-1-port1: cannot reset (err = -71)
[ 1502.932725] usb 2-1-port1: cannot reset (err = -71)
[ 1502.937763] usb 2-1-port1: cannot reset (err = -71)
[ 1502.942743] usb 2-1-port1: Cannot enable. Maybe the USB cable is bad?
[ 1502.949334] usb 2-1.1: the parent's name is 2-1
[ 1502.949373] usb 2-1-port1: Device no response
[ 1502.953893] usb 2-1-port1: unable to enumerate USB device
[ 1502.959652] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 1502.961076] r8152 1-2.1:1.0 eth0: carrier on
[ 1503.707308] hub 2-1:1.0: set hub depth failed
[ 1503.815273] usb 2-1: USB disconnect, device number 5-
tobetter
- Posts: 11949
- Joined: Mon Feb 25, 2013 10:55 am
- languages_spoken: Korean, English
- ODROIDs: Many
- Location: Paju, South Korea
- Has thanked: 834 times
- Been thanked: 2016 times
- Contact:
Re: USB to ethernet adapter not working on N2L
@paulcrawford, thank you for the detail logs.
[ 1455.877688] r8152 1-2.1:1.0 eth0: Rx status -71 error message makes me worry about the connection capability or USB compatibility issue with your ethernet dongle. The error number -71 happens when cable connection is not good so USB communication is unstable, AFAIK. Would you be able to put a USB 3.0 hub between your ODROID-N2L and the ethernet dongle, so you can observe if the issue still present?
[ 1455.877688] r8152 1-2.1:1.0 eth0: Rx status -71 error message makes me worry about the connection capability or USB compatibility issue with your ethernet dongle. The error number -71 happens when cable connection is not good so USB communication is unstable, AFAIK. Would you be able to put a USB 3.0 hub between your ODROID-N2L and the ethernet dongle, so you can observe if the issue still present?
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
@tobetter, I do not have a USB 3.0 hub available other than the Aceele ethernet adapter that includes a three port USB 3.0 hub in addition to the RJ45 port. So I tried plugging the Atolla adapter into a Aceele adapter/hub USB 3.0 port, having removed a USBtinyISP device from that port, and moved the ethernet cable from the Aceele adapter to the Atolla RJ45 port. Then I tried to connect via ssh and failed. Moving the ethernet cable back to the Aceele adapter allowed the ssh connection. Then the USBtinyISP was reconnected to the Aceele USB 3.0 hub port.
Here is the dmesg result on the above:
Here is the dmesg result on the above:
Code: Select all
[ 2735.395472] aml_card_probe error ret:-517
[ 8502.933324] usb 1-2.4: USB disconnect, device number 10
[ 8507.789440] usb 1-2.4: new high-speed USB device number 11 using xhci-hcd
[ 8507.926451] usb 1-2.4: New USB device found, idVendor=05e3, idProduct=0610
[ 8507.926453] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 8507.926455] usb 1-2.4: Product: USB2.1 Hub
[ 8507.926456] usb 1-2.4: Manufacturer: GenesysLogic
[ 8507.957491] hub 1-2.4:1.0: USB hub found
[ 8507.959233] hub 1-2.4:1.0: 4 ports detected
[ 8507.967030] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 8507.971474] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 8507.977201] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 8507.985946] aml_card_probe error ret:-517
[ 8508.281418] usb 1-2.4.4: new high-speed USB device number 12 using xhci-hcd
[ 8508.406836] usb 1-2.4.4: New USB device found, idVendor=0bda, idProduct=8153
[ 8508.406839] usb 1-2.4.4: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 8508.406840] usb 1-2.4.4: Product: USB 10/100/1000 LAN
[ 8508.406841] usb 1-2.4.4: Manufacturer: Realtek
[ 8508.406843] usb 1-2.4.4: SerialNumber: 000001
[ 8508.437085] usb 1-2.4.4: Unsupported device
[ 8508.437273] usb 1-2.4.4: Unsupported device
[ 8508.440595] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 8508.450214] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 8508.455927] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 8508.464729] aml_card_probe error ret:-517
[ 8508.628591] usb 1-2.4.4: reset high-speed USB device number 12 using xhci-hcd
[ 8508.812567] r8152 1-2.4.4:1.0 eth1: v2.10.00 (2018/03/16)
[ 8508.812572] r8152 1-2.4.4:1.0 eth1: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 8508.812990] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 8508.817533] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 8508.823206] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 8508.831933] aml_card_probe error ret:-517
[ 8509.044620] usb 1-2.4.4: reset high-speed USB device number 12 using xhci-hcd
[ 8509.236959] r8152 1-2.4.4:1.0 eth1: v2.10.00 (2018/03/16)
[ 8509.236964] r8152 1-2.4.4:1.0 eth1: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[ 8509.243732] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 8509.248293] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 8509.255002] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 8509.262912] aml_card_probe error ret:-517
[ 8509.307934] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 8509.316462] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 8515.928744] r8152 1-2.1:1.0 eth0: carrier off
[ 8522.613300] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 8522.614164] r8152 1-2.4.4:1.0 eth1: carrier on
[ 8555.813547] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.813585] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.813666] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.813704] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.813791] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.813832] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.813915] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.813953] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.814037] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.814081] r8152 1-2.4.4:1.0 eth1: Rx status -71
[ 8555.860653] r8152 1-2.4.4:1.0 eth1: Stop submitting intr, status -71
[ 8555.925430] usb 1-2.4: USB disconnect, device number 11
[ 8555.925433] usb 1-2.4.4: USB disconnect, device number 12
[ 8563.734431] r8152 1-2.1:1.0 eth0: carrier on
[ 8568.202876] usb 1-2.4: new low-speed USB device number 13 using xhci-hcd
[ 8568.331407] usb 1-2.4: New USB device found, idVendor=1781, idProduct=0c9f
[ 8568.331409] usb 1-2.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 8568.331411] usb 1-2.4: Product: USBtinyISP
[ 8568.331956] usb 1-2.4: Unsupported device
[ 8568.332326] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 8568.340586] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 8568.346295] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 8568.355048] aml_card_probe error ret:-517
-
tobetter
- Posts: 11949
- Joined: Mon Feb 25, 2013 10:55 am
- languages_spoken: Korean, English
- ODROIDs: Many
- Location: Paju, South Korea
- Has thanked: 834 times
- Been thanked: 2016 times
- Contact:
Re: USB to ethernet adapter not working on N2L
SInce it gives the same error number -71, I guess it's a USB compatible issue which has been long for ODROID-N2, the issue had been improved a couple of years ago but still looks like some USB devices are not stable.paulcrawford wrote: ↑Fri Mar 03, 2023 1:03 am@tobetter, I do not have a USB 3.0 hub available other than the Aceele ethernet adapter that includes a three port USB 3.0 hub in addition to the RJ45 port. So I tried plugging the Atolla adapter into a Aceele adapter/hub USB 3.0 port, having removed a USBtinyISP device from that port, and moved the ethernet cable from the Aceele adapter to the Atolla RJ45 port. Then I tried to connect via ssh and failed. Moving the ethernet cable back to the Aceele adapter allowed the ssh connection. Then the USBtinyISP was reconnected to the Aceele USB 3.0 hub port.
Here is the dmesg result on the above:
Code: Select all
[ 2735.395472] aml_card_probe error ret:-517 [ 8502.933324] usb 1-2.4: USB disconnect, device number 10 [ 8507.789440] usb 1-2.4: new high-speed USB device number 11 using xhci-hcd [ 8507.926451] usb 1-2.4: New USB device found, idVendor=05e3, idProduct=0610 [ 8507.926453] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0 [ 8507.926455] usb 1-2.4: Product: USB2.1 Hub [ 8507.926456] usb 1-2.4: Manufacturer: GenesysLogic [ 8507.957491] hub 1-2.4:1.0: USB hub found [ 8507.959233] hub 1-2.4:1.0: 4 ports detected [ 8507.967030] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null) [ 8507.971474] asoc-aml-card auge_sound: parse dai_link-2 fail [ 8507.977201] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY [ 8507.985946] aml_card_probe error ret:-517 [ 8508.281418] usb 1-2.4.4: new high-speed USB device number 12 using xhci-hcd [ 8508.406836] usb 1-2.4.4: New USB device found, idVendor=0bda, idProduct=8153 [ 8508.406839] usb 1-2.4.4: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [ 8508.406840] usb 1-2.4.4: Product: USB 10/100/1000 LAN [ 8508.406841] usb 1-2.4.4: Manufacturer: Realtek [ 8508.406843] usb 1-2.4.4: SerialNumber: 000001 [ 8508.437085] usb 1-2.4.4: Unsupported device [ 8508.437273] usb 1-2.4.4: Unsupported device [ 8508.440595] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null) [ 8508.450214] asoc-aml-card auge_sound: parse dai_link-2 fail [ 8508.455927] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY [ 8508.464729] aml_card_probe error ret:-517 [ 8508.628591] usb 1-2.4.4: reset high-speed USB device number 12 using xhci-hcd [ 8508.812567] r8152 1-2.4.4:1.0 eth1: v2.10.00 (2018/03/16) [ 8508.812572] r8152 1-2.4.4:1.0 eth1: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 8508.812990] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null) [ 8508.817533] asoc-aml-card auge_sound: parse dai_link-2 fail [ 8508.823206] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY [ 8508.831933] aml_card_probe error ret:-517 [ 8509.044620] usb 1-2.4.4: reset high-speed USB device number 12 using xhci-hcd [ 8509.236959] r8152 1-2.4.4:1.0 eth1: v2.10.00 (2018/03/16) [ 8509.236964] r8152 1-2.4.4:1.0 eth1: This product is covered by one or more of the following patents: US6,570,884, US6,115,776, and US6,327,625. [ 8509.243732] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null) [ 8509.248293] asoc-aml-card auge_sound: parse dai_link-2 fail [ 8509.255002] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY [ 8509.262912] aml_card_probe error ret:-517 [ 8509.307934] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 8509.316462] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 8515.928744] r8152 1-2.1:1.0 eth0: carrier off [ 8522.613300] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 8522.614164] r8152 1-2.4.4:1.0 eth1: carrier on [ 8555.813547] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.813585] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.813666] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.813704] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.813791] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.813832] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.813915] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.813953] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.814037] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.814081] r8152 1-2.4.4:1.0 eth1: Rx status -71 [ 8555.860653] r8152 1-2.4.4:1.0 eth1: Stop submitting intr, status -71 [ 8555.925430] usb 1-2.4: USB disconnect, device number 11 [ 8555.925433] usb 1-2.4.4: USB disconnect, device number 12 [ 8563.734431] r8152 1-2.1:1.0 eth0: carrier on [ 8568.202876] usb 1-2.4: new low-speed USB device number 13 using xhci-hcd [ 8568.331407] usb 1-2.4: New USB device found, idVendor=1781, idProduct=0c9f [ 8568.331409] usb 1-2.4: New USB device strings: Mfr=0, Product=2, SerialNumber=0 [ 8568.331411] usb 1-2.4: Product: USBtinyISP [ 8568.331956] usb 1-2.4: Unsupported device [ 8568.332326] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null) [ 8568.340586] asoc-aml-card auge_sound: parse dai_link-2 fail [ 8568.346295] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY [ 8568.355048] aml_card_probe error ret:-517
-
mad_ady
- Posts: 11446
- Joined: Wed Jul 15, 2015 5:00 pm
- languages_spoken: english
- ODROIDs: XU4 (HC1, HC2), C1+, C2, C4 (HC4), N1, N2, N2L, H2, H3+, Go, Go Advance, M1
- Location: Bucharest, Romania
- Has thanked: 647 times
- Been thanked: 1115 times
- Contact:
Re: USB to ethernet adapter not working on N2L
This is normal. Each interface gets its own ip address via dhcp. Always check what the current IP is in your dhcp server logs.If I move the ethernet cable from the Aceele adapter to the Atolla adapter, the ssh connection is lost although the lights on the RJ45 port on the Atolla adapter are working as they should.
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
@mad_ady, You are absolutely correct, the Atolla did get a different IP address when plugged into the Aceele which was in turn connected to the USB 2.0 port on the N2L. My mind was on the way things would have worked on my N2+ where the MAC address is internal to the SBC. With the dongles the MAC address is on them. I changed the reserved IP address for the Atolla to the one I used to use on the Aceele and now everything works fine again on both dongles.
@tobetter, It is clear from the above that the real problem is the USB 3.0 port on the N2L because when I connect the Atolla dongle to the USB 3.0 port there is no ssh connection. So the original problem I had with the TX status -71 was likely nothing to do with the Aceele dongle but rather the USB 3.0 port on the N2L. This is very disappointing that there are still USB issues with the N2 series. One of the main reasons I switched to the N2L from the N2+ was that none of the four USB ports worked anymore and although the OTG port still worked and could function on some USB tasks, doing an AVRDUDE programming of a MegaAT328p was not one of them. I really thought moving to the N2L would end my USB problems and for about two and half months it did. All of the devices that I have connected to the USB hub part of the Atolla or Aceele dongles are only USB 2.0 anyway so I am not loosing anything there but not having USB 3.0 will prevent the dongle from providing gigabit ethernet. Although since most access to the N2L web server is via WiFi anyway, perhaps even the gigabit ethernet is not that important. If the USB 2.0 port on the N2L also failed, the N2L would become a very expensive paper weight to me.
Is there anything I can do to help sort out this USB issue since I have failed N2L? Also have there been other reports of problems with N2L USB ports? I don't recall seeing any in the forum which I check daily.
@tobetter, It is clear from the above that the real problem is the USB 3.0 port on the N2L because when I connect the Atolla dongle to the USB 3.0 port there is no ssh connection. So the original problem I had with the TX status -71 was likely nothing to do with the Aceele dongle but rather the USB 3.0 port on the N2L. This is very disappointing that there are still USB issues with the N2 series. One of the main reasons I switched to the N2L from the N2+ was that none of the four USB ports worked anymore and although the OTG port still worked and could function on some USB tasks, doing an AVRDUDE programming of a MegaAT328p was not one of them. I really thought moving to the N2L would end my USB problems and for about two and half months it did. All of the devices that I have connected to the USB hub part of the Atolla or Aceele dongles are only USB 2.0 anyway so I am not loosing anything there but not having USB 3.0 will prevent the dongle from providing gigabit ethernet. Although since most access to the N2L web server is via WiFi anyway, perhaps even the gigabit ethernet is not that important. If the USB 2.0 port on the N2L also failed, the N2L would become a very expensive paper weight to me.
Is there anything I can do to help sort out this USB issue since I have failed N2L? Also have there been other reports of problems with N2L USB ports? I don't recall seeing any in the forum which I check daily.
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
I am running two RS485 to USB converters. Until today I have had no problems with either one. Now the one will not stay connected via the Atolla USB 3.0 hub/ethernet adapter to the USB 2.0 port on the N2L while the other one works fine connected to the same USB 3.0 hub.
This is the dmesg output:
When I had the problems with Aceele ethernet adapter I assumed that the problem was with that adapter so I bought another adapter. With this issue I would appreciate Hardkernel confirming that the problem is likely with RS485 to USB converter and not the N2L. The converter is made by Waveshare and costs about twice as much as the ethernet adapters so before I replace this one with another I want to be sure that the problem is with it and not the N2L. If necessary I could move the one that does not work into the position of the one that does work but that would mean changing the wiring and the udev rules.
This is the dmesg output:
Code: Select all
[ 6329.659544] usb 1-2-port1: disabled by hub (EMI?), re-enabling...
[ 6329.661150] usb 1-2.1: USB disconnect, device number 100
[ 6329.661354] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 6329.661368] ftdi_sio 1-2.1:1.0: device disconnected
[ 6329.907450] usb 1-2.1: new full-speed USB device number 101 using xhci-hcd
[ 6330.037588] usb 1-2.1: New USB device found, idVendor=0403, idProduct=6001
[ 6330.037590] usb 1-2.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 6330.037592] usb 1-2.1: Product: FT232R USB UART
[ 6330.037593] usb 1-2.1: Manufacturer: FTDI
[ 6330.037594] usb 1-2.1: SerialNumber: AR0K4C6O
[ 6330.040156] ftdi_sio 1-2.1:1.0: FTDI USB Serial Device converter detected
[ 6330.040190] usb 1-2.1: Detected FT232RL
[ 6330.040443] ftdi_sio ttyUSB0: Unable to write latency timer: -32
[ 6330.043601] usb 1-2.1: FTDI USB Serial Device converter now attached to ttyUSB0
[ 6330.043995] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 6330.051048] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 6330.056783] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 6330.065530] aml_card_probe error ret:-517
[ 6330.171218] usb 1-2-port1: disabled by hub (EMI?), re-enabling...
[ 6330.172783] usb 1-2.1: USB disconnect, device number 101
[ 6330.172960] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[ 6330.172972] ftdi_sio 1-2.1:1.0: device disconnected
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
I have now switched the two Waveshare RS485 to USB devices, first without changing the USB cables from the hub to the device. Still there was an issue with device on the original RS485 network that had the problem before. So the problem does not seem to be with the Waveshare devices. Then I switched the USB cables from the hub to the Waveshare devices so that each had its original cable but also still coming from the same port on the USB hub, Still the device on the RS485 network keeps getting dropped even on a different hub port.
Here is the dmesg now:
Unless the source of the problem is in the USB hub, this would suggest that the N2L USB 2.0 port is the problem. To test that I removed the USB hub/adapter and plugged the Waveshare directly into the N2L USB 2.0 port. The following dmesg shows all of this, but the Waveshare device is not disconnected in software only in hardware. The Waveshare was connected directly for only 90 seconds. Perhaps that was not long enough to be disconnected in software
Next I unplugged the Waveshare from the N2L, plugged the USB hub into the N2L USB 2.0 and then plugged the Waveshare into the USB hub.
The dmesg output follows:
This has been stable for a while so I will run Linux C code that uses the Waveshare. So good news, both Waveshare devices seem to be working fine again but perhaps that is only coincidence as there are only infrequent commands sent on that RS485 network. Just checked again and the code tried to access the RS485 network when the device had been disconnected so there was an error. But if the code gets an error it tries again up to 10 times. Looking at the dmesg again below it seems that the time period of the Waveshare device been connected is variable: sometimes essentially 0 seconds to as much as about 20 seconds. This would explain why an error infrequently shows up in the code even though the USB connection is often not working at all.
With the known history of USB problems on the N2 series, I am inclined to think that my present issues may be a manifestation of those problems but I do not know enough about the problems to say for sure. Unfortunately I do not have another N2L available to test right now but I was planning on getting another one anyway as a backup.
Can someone please review the dmesg output to determine where the fault seems to lie?
Here is the dmesg now:
Code: Select all
[ 1959.083910] usb 1-2.3: Manufacturer: FTDI
[ 1959.083911] usb 1-2.3: SerialNumber: AR0K5836
[ 1959.086598] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[ 1959.086630] usb 1-2.3: Detected FT232RL
[ 1959.087138] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB1
[ 1959.087532] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1959.091981] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1959.097714] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1959.106472] aml_card_probe error ret:-517
[ 1959.215340] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[ 1959.216839] usb 1-2.3: USB disconnect, device number 13
[ 1959.217032] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
[ 1959.217046] ftdi_sio 1-2.3:1.0: device disconnected
[ 1959.465501] usb 1-2.3: new full-speed USB device number 14 using xhci-hcd
[ 1959.595905] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[ 1959.595907] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1959.595909] usb 1-2.3: Product: FT232R USB UART
[ 1959.595910] usb 1-2.3: Manufacturer: FTDI
[ 1959.595912] usb 1-2.3: SerialNumber: AR0K5836
[ 1959.598593] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[ 1959.598624] usb 1-2.3: Detected FT232RL
[ 1959.599081] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB1
[ 1959.599465] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1959.603910] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1959.609657] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1959.618594] aml_card_probe error ret:-517
[ 1959.983088] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[ 1959.984591] usb 1-2.3: USB disconnect, device number 14
[ 1959.984755] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
[ 1959.984767] ftdi_sio 1-2.3:1.0: device disconnected
[ 1960.233475] usb 1-2.3: new full-speed USB device number 15 using xhci-hcd
[ 1960.363904] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[ 1960.363906] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1960.363908] usb 1-2.3: Product: FT232R USB UART
[ 1960.363909] usb 1-2.3: Manufacturer: FTDI
[ 1960.363911] usb 1-2.3: SerialNumber: AR0K5836
[ 1960.366597] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[ 1960.366626] usb 1-2.3: Detected FT232RL
[ 1960.369746] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB1
[ 1960.370100] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[ 1960.374559] asoc-aml-card auge_sound: parse dai_link-2 fail
[ 1960.380270] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[ 1960.389050] aml_card_probe error ret:-517Code: Select all
[18803.248530] usb 1-2.1: USB disconnect, device number 18
[18803.248717] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[18803.248733] ftdi_sio 1-2.1:1.0: device disconnected
[18812.464650] usb 1-2.3: USB disconnect, device number 20
[18812.464812] ftdi_sio ttyUSB1: FTDI USB Serial Device converter now disconnected from ttyUSB1
[18812.464824] ftdi_sio 1-2.3:1.0: device disconnected
[18822.492278] r8152 1-2.2.1:1.0 eth0: Stop submitting intr, status -71
[18822.704526] usb 1-2.2: USB disconnect, device number 19
[18822.704528] usb 1-2.2.1: USB disconnect, device number 21
[18822.764266] usb 1-2.2.2: USB disconnect, device number 23
[18822.765018] usb 1-2.2.3: USB disconnect, device number 24
[18832.512182] usb 1-2: USB disconnect, device number 17
[18832.512186] usb 1-2.4: USB disconnect, device number 22
[18832.512290] r8152 1-2.4:1.0 eth1: Stop submitting intr, status -108
[18846.898200] usb 1-2: new full-speed USB device number 25 using xhci-hcd
[18847.043480] usb 1-2: New USB device found, idVendor=0403, idProduct=6001
[18847.043482] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[18847.043484] usb 1-2: Product: FT232R USB UART
[18847.043485] usb 1-2: Manufacturer: FTDI
[18847.043487] usb 1-2: SerialNumber: AR0K5836
[18847.045926] ftdi_sio 1-2:1.0: FTDI USB Serial Device converter detected
[18847.045958] usb 1-2: Detected FT232RL
[18847.046682] usb 1-2: FTDI USB Serial Device converter now attached to ttyUSB0
[18847.047082] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[18847.051543] asoc-aml-card auge_sound: parse dai_link-2 fail
[18847.057274] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[18847.066175] aml_card_probe error ret:-517
The dmesg output follows:
Code: Select all
[18937.462453] usb 1-2: USB disconnect, device number 25
[18937.462640] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[18937.462652] ftdi_sio 1-2:1.0: device disconnected
[18948.161983] usb 1-2: new high-speed USB device number 26 using xhci-hcd
[18948.315179] usb 1-2: New USB device found, idVendor=05e3, idProduct=0610
[18948.315182] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[18948.315183] usb 1-2: Product: USB2.1 Hub
[18948.315185] usb 1-2: Manufacturer: GenesysLogic
[18948.333210] hub 1-2:1.0: USB hub found
[18948.334628] hub 1-2:1.0: 4 ports detected
[18948.342447] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[18948.346885] asoc-aml-card auge_sound: parse dai_link-2 fail
[18948.352634] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[18948.361379] aml_card_probe error ret:-517
[18948.657963] usb 1-2.4: new high-speed USB device number 27 using xhci-hcd
[18948.782484] usb 1-2.4: New USB device found, idVendor=0bda, idProduct=8153
[18948.782486] usb 1-2.4: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[18948.782488] usb 1-2.4: Product: USB 10/100/1000 LAN
[18948.782489] usb 1-2.4: Manufacturer: Realtek
[18948.782490] usb 1-2.4: SerialNumber: 000001
[18948.812507] usb 1-2.4: Unsupported device
[18948.812688] usb 1-2.4: Unsupported device
[18948.815644] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[18948.825293] asoc-aml-card auge_sound: parse dai_link-2 fail
[18948.831019] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[18948.839807] aml_card_probe error ret:-517
[18949.004138] usb 1-2.4: reset high-speed USB device number 27 using xhci-hcd
[18949.186384] r8152 1-2.4:1.0 eth0: v2.16.1 (2022/04/12)
[18949.186387] r8152 1-2.4:1.0 eth0: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[18949.186760] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[18949.191757] asoc-aml-card auge_sound: parse dai_link-2 fail
[18949.196947] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[18949.205694] aml_card_probe error ret:-517
[18949.420166] usb 1-2.4: reset high-speed USB device number 27 using xhci-hcd
[18949.606090] r8152 1-2.4:1.0 eth0: v2.16.1 (2022/04/12)
[18949.606095] r8152 1-2.4:1.0 eth0: This product is covered by one or more of the following patents:
US6,570,884, US6,115,776, and US6,327,625.
[18949.606608] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[18949.611184] asoc-aml-card auge_sound: parse dai_link-2 fail
[18949.622180] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[18949.625796] aml_card_probe error ret:-517
[18949.682780] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[18949.687938] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[18952.524972] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[18952.525926] r8152 1-2.4:1.0 eth0: carrier on
[18978.344726] usb 1-2.3: new full-speed USB device number 28 using xhci-hcd
[18978.475090] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[18978.475092] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[18978.475094] usb 1-2.3: Product: FT232R USB UART
[18978.475096] usb 1-2.3: Manufacturer: FTDI
[18978.475097] usb 1-2.3: SerialNumber: AR0K5836
[18978.477906] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[18978.477940] usb 1-2.3: Detected FT232RL
[18978.481975] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[18978.482366] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)Code: Select all
[21959.597467] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[21959.597469] usb 1-2.3: Product: FT232R USB UART
[21959.597470] usb 1-2.3: Manufacturer: FTDI
[21959.597472] usb 1-2.3: SerialNumber: AR0K5836
[21959.600018] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[21959.600048] usb 1-2.3: Detected FT232RL
[21959.603929] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[21959.604320] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[21959.608801] asoc-aml-card auge_sound: parse dai_link-2 fail
[21959.614494] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[21959.623244] aml_card_probe error ret:-517
[21968.686898] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[21968.688533] usb 1-2.3: USB disconnect, device number 12
[21968.688728] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[21968.688740] ftdi_sio 1-2.3:1.0: device disconnected
[21968.938991] usb 1-2.3: new full-speed USB device number 13 using xhci-hcd
[21969.068965] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[21969.068968] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[21969.068969] usb 1-2.3: Product: FT232R USB UART
[21969.068971] usb 1-2.3: Manufacturer: FTDI
[21969.068972] usb 1-2.3: SerialNumber: AR0K5836
[21969.071514] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[21969.071543] usb 1-2.3: Detected FT232RL
[21969.072111] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[21969.072490] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[21969.076954] asoc-aml-card auge_sound: parse dai_link-2 fail
[21969.082672] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[21969.091434] aml_card_probe error ret:-517
[21969.967014] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[21969.968638] usb 1-2.3: USB disconnect, device number 13
[21969.969028] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[21969.969052] ftdi_sio 1-2.3:1.0: device disconnected
[21970.214940] usb 1-2.3: new full-speed USB device number 14 using xhci-hcd
[21970.345080] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[21970.345083] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[21970.345085] usb 1-2.3: Product: FT232R USB UART
[21970.345086] usb 1-2.3: Manufacturer: FTDI
[21970.345088] usb 1-2.3: SerialNumber: AR0K5836
[21970.347643] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[21970.347673] usb 1-2.3: Detected FT232RL
[21970.351275] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[21970.351645] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[21970.356119] asoc-aml-card auge_sound: parse dai_link-2 fail
[21970.361827] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[21970.370576] aml_card_probe error ret:-517
[21978.671143] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[21978.672659] usb 1-2.3: USB disconnect, device number 14
[21978.672864] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[21978.672877] ftdi_sio 1-2.3:1.0: device disconnected
[21978.922574] usb 1-2.3: new full-speed USB device number 15 using xhci-hcd
[21979.052710] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[21979.052712] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[21979.052714] usb 1-2.3: Product: FT232R USB UART
[21979.052715] usb 1-2.3: Manufacturer: FTDI
[21979.052716] usb 1-2.3: SerialNumber: AR0K5836
[21979.055397] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[21979.055427] usb 1-2.3: Detected FT232RL
[21979.058936] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[21979.059326] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[21979.063847] asoc-aml-card auge_sound: parse dai_link-2 fail
[21979.069500] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[21979.078261] aml_card_probe error ret:-517
[21983.022888] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[21983.024514] usb 1-2.3: USB disconnect, device number 15
[21983.024703] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[21983.024714] ftdi_sio 1-2.3:1.0: device disconnected
[21983.274389] usb 1-2.3: new full-speed USB device number 16 using xhci-hcd
[21983.404461] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[21983.404463] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[21983.404465] usb 1-2.3: Product: FT232R USB UART
[21983.404466] usb 1-2.3: Manufacturer: FTDI
[21983.404467] usb 1-2.3: SerialNumber: AR0K5836
[21983.407143] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[21983.407185] usb 1-2.3: Detected FT232RL
[21983.410552] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[21983.410950] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[21983.415414] asoc-aml-card auge_sound: parse dai_link-2 fail
[21983.421113] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[21983.430007] aml_card_probe error ret:-517
[22002.479140] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[22002.480764] usb 1-2.3: USB disconnect, device number 16
[22002.480969] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[22002.480983] ftdi_sio 1-2.3:1.0: device disconnected
[22002.729574] usb 1-2.3: new full-speed USB device number 17 using xhci-hcd
[22002.859828] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[22002.859830] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[22002.859832] usb 1-2.3: Product: FT232R USB UART
[22002.859833] usb 1-2.3: Manufacturer: FTDI
[22002.859834] usb 1-2.3: SerialNumber: AR0K5836
[22002.862518] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[22002.862551] usb 1-2.3: Detected FT232RL
[22002.863108] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[22002.863531] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[22002.867995] asoc-aml-card auge_sound: parse dai_link-2 fail
[22002.873711] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[22002.882478] aml_card_probe error ret:-517
[22003.502891] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[22003.504436] usb 1-2.3: USB disconnect, device number 17
[22003.504845] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[22003.504931] ftdi_sio 1-2.3:1.0: device disconnected
[22003.753530] usb 1-2.3: new full-speed USB device number 18 using xhci-hcd
[22003.883586] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[22003.883588] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[22003.883590] usb 1-2.3: Product: FT232R USB UART
[22003.883591] usb 1-2.3: Manufacturer: FTDI
[22003.883592] usb 1-2.3: SerialNumber: AR0K5836
[22003.886143] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[22003.886182] usb 1-2.3: Detected FT232RL
[22003.889675] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[22003.890090] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[22003.894548] asoc-aml-card auge_sound: parse dai_link-2 fail
[22003.900262] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[22003.909017] aml_card_probe error ret:-517
[22013.743142] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[22013.744769] usb 1-2.3: USB disconnect, device number 18
[22013.744985] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[22013.744998] ftdi_sio 1-2.3:1.0: device disconnected
[22013.997097] usb 1-2.3: new full-speed USB device number 19 using xhci-hcd
[22014.127210] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[22014.127213] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[22014.127214] usb 1-2.3: Product: FT232R USB UART
[22014.127216] usb 1-2.3: Manufacturer: FTDI
[22014.127217] usb 1-2.3: SerialNumber: AR0K5836
[22014.129765] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[22014.129802] usb 1-2.3: Detected FT232RL
[22014.133268] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[22014.133688] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[22014.138145] asoc-aml-card auge_sound: parse dai_link-2 fail
[22014.143874] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[22014.154046] aml_card_probe error ret:-517Can someone please review the dmesg output to determine where the fault seems to lie?
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
Here is the latest dmesg which stopped the c code completely waiting for the serial port to respond:
Just unplugged the Waveshare device from the hub and replugged it. The c code now works perfectly again.
Code: Select all
[27270.703122] usb 1-2-port3: disabled by hub (EMI?), re-enabling...
[27270.704682] usb 1-2.3: USB disconnect, device number 18
[27270.705797] ftdi_sio ttyUSB0: FTDI USB Serial Device converter now disconnected from ttyUSB0
[27270.705810] ftdi_sio 1-2.3:1.0: device disconnected
[27270.952482] usb 1-2.3: new full-speed USB device number 19 using xhci-hcd
[27271.056546] usb 1-2.3: Device not responding to setup address.
[27271.264547] usb 1-2.3: Device not responding to setup address.
[27271.472460] usb 1-2.3: device not accepting address 19, error -71
[27271.576456] usb 1-2.3: new full-speed USB device number 20 using xhci-hcd
[27271.706559] usb 1-2.3: New USB device found, idVendor=0403, idProduct=6001
[27271.706561] usb 1-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[27271.706563] usb 1-2.3: Product: FT232R USB UART
[27271.706564] usb 1-2.3: Manufacturer: FTDI
[27271.706566] usb 1-2.3: SerialNumber: AR0K5836
[27271.709254] ftdi_sio 1-2.3:1.0: FTDI USB Serial Device converter detected
[27271.709286] usb 1-2.3: Detected FT232RL
[27271.712583] usb 1-2.3: FTDI USB Serial Device converter now attached to ttyUSB0
[27271.713013] asoc-aml-card auge_sound: aml_card_dai_link_of, dai-link idx:2, error getting cpu dai name:(null)
[27271.717477] asoc-aml-card auge_sound: parse dai_link-2 fail
[27271.723215] asoc-aml-card auge_sound: aml_card_probe, aml_card_parse_of error -517 PROBE RETRY
[27271.733383] aml_card_probe error ret:-517
[27278.861131] ftdi_sio ttyUSB0: ftdi_set_termios FAILED to set databits/stopbits/parity
[27278.863675] ftdi_sio ttyUSB0: ftdi_set_termios urb failed to set baudrate
[27278.872272] ftdi_sio ttyUSB0: urb failed to clear flow control
[27278.876631] ftdi_sio ttyUSB0: usb_serial_generic_read_bulk_callback - urb stopped: -32
[27278.884497] ftdi_sio ttyUSB0: urb failed to clear flow control
[27278.884542] ftdi_sio ttyUSB0: usb_serial_generic_read_bulk_callback - urb stopped: -32
[27278.918920] ftdi_sio ttyUSB0: usb_serial_generic_write_bulk_callback - urb stopped: -32
[29774.449063] ftdi_sio ttyUSB0: failed to get modem status: -32
[29790.767564] meson_uart ffd24000.serial: ttyS1 use xtal(24M) 24000000 change 38400 to 38400
[29799.255424] ftdi_sio ttyUSB0: ftdi_set_termios FAILED to set databits/stopbits/parity
[29799.257916] ftdi_sio ttyUSB0: ftdi_set_termios urb failed to set baudrate
[29799.266829] ftdi_sio ttyUSB0: urb failed to clear flow control
[29799.270881] ftdi_sio ttyUSB0: usb_serial_generic_read_bulk_callback - urb stopped: -32
[29799.278899] ftdi_sio ttyUSB0: usb_serial_generic_read_bulk_callback - urb stopped: -32
[29799.286839] ftdi_sio ttyUSB0: urb failed to clear flow control
[29799.313161] ftdi_sio ttyUSB0: usb_serial_generic_write_bulk_callback - urb stopped: -32
-
mad_ady
- Posts: 11446
- Joined: Wed Jul 15, 2015 5:00 pm
- languages_spoken: english
- ODROIDs: XU4 (HC1, HC2), C1+, C2, C4 (HC4), N1, N2, N2L, H2, H3+, Go, Go Advance, M1
- Location: Bucharest, Romania
- Has thanked: 647 times
- Been thanked: 1115 times
- Contact:
Re: USB to ethernet adapter not working on N2L
Not sure it applies to the N2L, and neither a solution, but if replugging a device "fixes" the issue you may have a software workaround. There may be some gpio you can toggle to force reset the usb hub, or maybe using uhubctl https://github.com/mvp/uhubctl to toggle power per port.
You could detect the issue by running a script that parses dmesg output and reset the faulty port.
You could detect the issue by running a script that parses dmesg output and reset the faulty port.
- These users thanked the author mad_ady for the post:
- paulcrawford (Sun Mar 05, 2023 9:50 pm)
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
@mad_ady, This is a very interesting approach. I checked the N2L USB root hub with lsusb -v and found that it does support per port power switching. I just had another code stoppage which was cured with plugging and replugging the USB to RS485 converter USB cable which is connected to the Atolla USB hub. That hub, however, does not support per port power switching so I would need to switch the power to all USB connections downstream of the N2L USB 2.0 port. Disconnecting all of the USB ports may still work as each one is used independently by the code and specifically setup by the code when required. There is a watchdog timer on the N2L which has a repair script. I could add the dmesg command with a grep to determine if the specific port has stopped functioning. I am just waiting now for the USB converter to stop functioning so that I can manually switch power at the N2L to get the code running again without doing a killall and start the code again. As I type the code did stop again, so I did the manual switch at the N2L USB 2.0 port and just like magic the code started to run again. So I think this could actually work.
My philosophy on software development is, however, that if things get too complicated, the original approach to the code was probably not the best. In this case, I am thinking that, given the history of USB issues on the N2 series, I may be better to switch to ethernet for communicating with the various data collecting devices via Modbus on RS485. The only weak link then would be that, since the N2L does not have native ethernet, I would still have to depend on the USB to ethernet adapter having a solid USB connection. I already know that, on the N2L I have, I cannot depend on the USB 3.0 port. How long the USB 2.0 port will last is anybody's guess.
I have ordered another N2L as a backup and since I now have two USB to ethernet adapters as well, perhaps I will connect one to each port to monitor the reliability. I also found and ordered an ethernet to RS485 converter. So the new challenge will be to rewrite the parts of the code that communicate with Modbus via USB serial ports to using ethernet instead. Preliminary research indicates that c is well adapted to doing just that.
Thanks again for your suggestion. You can always be depended upon to come up with novel approaches to problem solving.
My philosophy on software development is, however, that if things get too complicated, the original approach to the code was probably not the best. In this case, I am thinking that, given the history of USB issues on the N2 series, I may be better to switch to ethernet for communicating with the various data collecting devices via Modbus on RS485. The only weak link then would be that, since the N2L does not have native ethernet, I would still have to depend on the USB to ethernet adapter having a solid USB connection. I already know that, on the N2L I have, I cannot depend on the USB 3.0 port. How long the USB 2.0 port will last is anybody's guess.
I have ordered another N2L as a backup and since I now have two USB to ethernet adapters as well, perhaps I will connect one to each port to monitor the reliability. I also found and ordered an ethernet to RS485 converter. So the new challenge will be to rewrite the parts of the code that communicate with Modbus via USB serial ports to using ethernet instead. Preliminary research indicates that c is well adapted to doing just that.
Thanks again for your suggestion. You can always be depended upon to come up with novel approaches to problem solving.
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
@mad_ady, I just had a stoppage of the code because it could not connect to the device after trying 10 times. I disconnected and reconnected the USB hub at the N2L USB 2.0 port but there did not clear the fault. Then I disconnected and reconnected the device USB cable from the USB hub and the code continued. This hub as mentioned before does not support per port power switching so it would not cure the problem. Perhaps a different USB hub/ethernet adapter would work.
Getting too complicated again!
Getting too complicated again!
-
odroid
- Site Admin
- Posts: 41084
- Joined: Fri Feb 22, 2013 11:14 pm
- languages_spoken: English, Korean
- ODROIDs: ODROID
- Has thanked: 3194 times
- Been thanked: 1753 times
- Contact:
Re: USB to ethernet adapter not working on N2L
I've overlooked this thread. Sorry.
Can you please double check the part number of your Ethernet adapter controller chipset?
Is it RTL8153 or RTL8152?
As far as I know, RTL8153 is a USB 3.0 device while RTL8152 is a USB 2.0 device.
But your dmesg output showed RTL8152. I think they probably share a single device driver though.
Once you confirm the part number, we will buy a similar adapter which has the same chipset to reproduce the issue.
Can you please double check the part number of your Ethernet adapter controller chipset?
Is it RTL8153 or RTL8152?
As far as I know, RTL8153 is a USB 3.0 device while RTL8152 is a USB 2.0 device.
But your dmesg output showed RTL8152. I think they probably share a single device driver though.
Once you confirm the part number, we will buy a similar adapter which has the same chipset to reproduce the issue.
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
For my main N2L:
Code: Select all
$ lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 005: ID 0bda:8153 Realtek Semiconductor Corp. RTL8153 Gigabit Ethernet Adapter
Bus 001 Device 004: ID 1781:0c9f Multiple Vendors USBtiny
Bus 001 Device 006: ID 08a9:0014 CWAV Inc. USBee AX-Pro
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Code: Select all
$ lsusb
Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 001 Device 006: ID 0951:173c Kingston Technology DataTraveler Duo
Bus 001 Device 007: ID 0951:173c Kingston Technology DataTraveler Duo
Bus 001 Device 003: ID 0bda:8153 Realtek Semiconductor Corp. RTL8153 Gigabit Ethernet Adapter
Bus 001 Device 002: ID 05e3:0610 Genesys Logic, Inc. Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-
odroid
- Site Admin
- Posts: 41084
- Joined: Fri Feb 22, 2013 11:14 pm
- languages_spoken: English, Korean
- ODROIDs: ODROID
- Has thanked: 3194 times
- Been thanked: 1753 times
- Contact:
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
Re: USB to ethernet adapter not working on N2L
This is the link to the one USB to Ethernet dongle:
https://www.amazon.ca/dp/B082CDVHY8?psc ... ct_details
This is the other one:
https://www.amazon.ca/dp/B09JS3T9V2?psc ... ct_details
https://www.amazon.ca/dp/B082CDVHY8?psc ... ct_details
This is the other one:
https://www.amazon.ca/dp/B09JS3T9V2?psc ... ct_details
-
odroid
- Site Admin
- Posts: 41084
- Joined: Fri Feb 22, 2013 11:14 pm
- languages_spoken: English, Korean
- ODROIDs: ODROID
- Has thanked: 3194 times
- Been thanked: 1753 times
- Contact:
Re: USB to ethernet adapter not working on N2L
We found a couple of different RTL8153 dongles in Korea and ordered.
We will test it in the next week.
We will test it in the next week.
-
odroid
- Site Admin
- Posts: 41084
- Joined: Fri Feb 22, 2013 11:14 pm
- languages_spoken: English, Korean
- ODROIDs: ODROID
- Has thanked: 3194 times
- Been thanked: 1753 times
- Contact:
Re: USB to ethernet adapter not working on N2L
We've tested various USB devices with ODROID-N2L USB host ports.
USB 1.0, 1.1 and 2.0 devices have no critical issue so far.
But, we found a few USB 3.0 (Super-Speed) devices which didn't work properly as you observed.
Note that when we connected the non-working USB 3.0 Ethernet devices to the USB 2.0 host on N2L, they worked, but of course the iperf measured speed drops to around ~300Mbps from normal ~900Mbps due to USB 2.0 bandwidth.
We think the USB 3.0 signal strength or integrity has a serious problem in the ODROID-N2L hardware design since all of those devices worked fine with other ODROID boards.
Therefore, ODROID-N2L USB 3.0 host port is very picky and has much worse compatibility / stability.
Sorry for the very bad news.
USB 1.0, 1.1 and 2.0 devices have no critical issue so far.
- Screenshot from 2023-05-30 16-59-01.png (154.01 KiB) Viewed 93 times
But, we found a few USB 3.0 (Super-Speed) devices which didn't work properly as you observed.
- Screenshot from 2023-05-30 17-13-39.png (131.35 KiB) Viewed 93 times
We think the USB 3.0 signal strength or integrity has a serious problem in the ODROID-N2L hardware design since all of those devices worked fine with other ODROID boards.
Therefore, ODROID-N2L USB 3.0 host port is very picky and has much worse compatibility / stability.
Sorry for the very bad news.
-
paulcrawford
- Posts: 247
- Joined: Tue May 10, 2016 11:51 am
- languages_spoken: english
- ODROIDs: c2, n2, n2+ and n2l
- Has thanked: 46 times
- Been thanked: 24 times
- Contact:
-
odroid
- Site Admin
- Posts: 41084
- Joined: Fri Feb 22, 2013 11:14 pm
- languages_spoken: English, Korean
- ODROIDs: ODROID
- Has thanked: 3194 times
- Been thanked: 1753 times
- Contact:
Re: USB to ethernet adapter not working on N2L
We've been looking into the issue more carefully.
I'm not sure if we can find a fix, but we're still looking for a real root cause, give us a couple of weeks.
I'm not sure if we can find a fix, but we're still looking for a real root cause, give us a couple of weeks.
Who is online
Users browsing this forum: No registered users and 1 guest