New Case Design

Post Reply
caiannello
Posts: 2
Joined: Sat Jan 19, 2019 4:16 am
languages_spoken: english
ODROIDs: ODROID-H2
Contact:

New Case Design

Unread post by caiannello » Sat Jan 19, 2019 4:36 am

Hi Everybody.

I designed and printed a new case that I'm proud of. (Attached) I was going for a compact design with M.2 SSD and RAM. There's room in there for a little 6mm fan, but it doesn't seem necessary. The print is in three pieces and one of them requires gluing. If there is enough interest, I can post the files somewhere like Thingiverse,

Cheers,
Craig
front.jpg
front.jpg (315.8 KiB) Viewed 494 times
back.jpg
back.jpg (361.97 KiB) Viewed 494 times

crashoverride
Posts: 4228
Joined: Tue Dec 30, 2014 8:42 pm
languages_spoken: english
ODROIDs: C1
Contact:

Re: New Case Design

Unread post by crashoverride » Sat Jan 19, 2019 4:45 am

caiannello wrote:
Sat Jan 19, 2019 4:36 am
If there is enough interest, I can post the files somewhere like Thingiverse,
Please do post them. I really like this case!

I would like to mod it so there is room from a single 2.5" HDD somewhere. My H2 configuration is M.2 SDD + 1 SATA HDD.

User avatar
rooted
Posts: 6271
Joined: Fri Dec 19, 2014 9:12 am
languages_spoken: english
Location: Gulf of Mexico, US
Contact:

Re: New Case Design

Unread post by rooted » Sat Jan 19, 2019 5:16 am

Very nice, I like how you integrated the power and reset.

User avatar
odroid
Site Admin
Posts: 29651
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID
Contact:

Re: New Case Design

Unread post by odroid » Sat Jan 19, 2019 10:03 am

Yes! Please share your great 3D design file.

caiannello
Posts: 2
Joined: Sat Jan 19, 2019 4:16 am
languages_spoken: english
ODROIDs: ODROID-H2
Contact:

Re: New Case Design

Unread post by caiannello » Sat Jan 19, 2019 12:13 pm

Attached is the project file for Sketchup 17.2, and STL files for printing.

Parts needed:
4 M3 screws (10mm)
4 Plastic Hex Standoffs (38mm x 7mm, Schurter 9633.8300)
4 Adhesive rubber feet

I glued port-plate to lid using epoxy. I glued standoffs into receptacles on lid also. I taped the button faces into the lid while installing the board.

Sources of hex standoffs:
https://www.mouser.com/ProductDetail/Sc ... m1JQ%3D%3D
https://www.digikey.com/product-detail/ ... ND/3533906

Cheers,
Craig
Attachments
odroid-h2_case_cai_stl.zip
(111.92 KiB) Downloaded 19 times
odroid_h2_case_cai_sketchup.zip
(1.74 MiB) Downloaded 19 times

User avatar
odroid
Site Admin
Posts: 29651
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID
Contact:

Re: New Case Design

Unread post by odroid » Mon Jan 21, 2019 9:10 am

Thank you for sharing the nice and practical design. :D

Post Reply

Return to “Projects”

Who is online

Users browsing this forum: No registered users and 1 guest