Battery Power for xu4?

Moderators: odroid, mdrjr

Battery Power for xu4?

Unread postby jl303 » Sun Jul 19, 2015 10:28 am

Hi,

Is there any battery that could power xu4?
A lot of portable battery packs I found for smartphones are 5v/2a.
Thanks,

JL
jl303
 
Posts: 53
Joined: Wed Dec 31, 2014 12:08 am
languages_spoken: english

Re: Battery Power for xu4?

Unread postby phaseshifter » Sun Jul 19, 2015 11:55 am

5v 2a it may run it with just browsing and no peripherals for 15 min`s ...learn ohms law and do the math you could parallel a few of them you may get an hour out of 4 of them depending on what you are doing with the Xu4
phaseshifter
 
Posts: 1467
Joined: Fri May 08, 2015 9:12 am
languages_spoken: english
ODROIDs: opp sys.. ubuntu ..c1+ ..c-2..xu3 ,xu4...
acc`s vu7,c-shell ,uart,hi-fi ,,hi-fi2,,show,w-board,6x16GB emmc`s 3.5 inch touch...other odroid acc`s as well

Re: Battery Power for xu4?

Unread postby odroid » Sun Jul 19, 2015 8:34 pm

I could see 2.5~3Amp of peak current in the booting process.
So the 5V/2A battery pack will cause instability seriously.
User avatar
odroid
Site Admin
 
Posts: 21796
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID

Re: Battery Power for xu4?

Unread postby jl303 » Mon Jul 20, 2015 1:16 pm

So I guess no luck... :(
I found some battery pack that delivers 4a total, but that's total ports combined, not through a single usb port.
jl303
 
Posts: 53
Joined: Wed Dec 31, 2014 12:08 am
languages_spoken: english

Re: Battery Power for xu4?

Unread postby PennState_UAS » Wed Jul 22, 2015 10:45 am

I wrote a post on how we powered our xu3 computers from a lipo battery. Here it is: viewtopic.php?f=97&t=14807

Pretty similar power requirements, we haven't tried it on an xu4 yet but our solution should work.
PennState_UAS
 
Posts: 6
Joined: Sat Jul 11, 2015 6:22 am
languages_spoken: english
ODROIDs: xu3

Re: Battery Power for xu4?

Unread postby jl303 » Thu Jul 30, 2015 5:49 am

I also found a portable battery that delivers 5v/4a through one usb port. It's called Anker 2nd Gen Astro3.
http://www.ianker.com/product/79AN7904S-B2A
I exchanged with Anker support, and they said it can deliver up to 4a through one usb port or combined. They sell many different batteries but they said this is the only battery that can do it so far.
I just received the battery and a usb to 5.5mm cable.
I just plugged it in with no soldering and no modification, and it seems working fine.
Anker 2nd Gen Astro3 12800mAh 3-Port 4A Portable Charger External Battery Power Bank with PowerIQ Technology
http://www.amazon.com/Anker-12800mAh-Po ... B00CEZBKTO
StarTech USB2TYPEM 3 Feet USB to Type M Barrel 5V DC Power Cable
http://www.amazon.com/gp/product/B003MQO96U
jl303
 
Posts: 53
Joined: Wed Dec 31, 2014 12:08 am
languages_spoken: english

Re: Battery Power for xu4?

Unread postby arich57 » Wed Aug 05, 2015 12:47 am

jl303 wrote:I also found a portable battery that delivers 5v/4a through one usb port. It's called Anker 2nd Gen Astro3.
http://www.ianker.com/product/79AN7904S-B2A
I exchanged with Anker support, and they said it can deliver up to 4a through one usb port or combined. They sell many different batteries but they said this is the only battery that can do it so far.
I just received the battery and a usb to 5.5mm cable.
I just plugged it in with no soldering and no modification, and it seems working fine.
Anker 2nd Gen Astro3 12800mAh 3-Port 4A Portable Charger External Battery Power Bank with PowerIQ Technology
http://www.amazon.com/Anker-12800mAh-Po ... B00CEZBKTO
StarTech USB2TYPEM 3 Feet USB to Type M Barrel 5V DC Power Cable
http://www.amazon.com/gp/product/B003MQO96U



Have you had enough time to play with this to have an idea of how long you can run the xu4 on this battery? I was looking for something similiar and curious what type of run times you are getting.

Thanks.
arich57
 
Posts: 2
Joined: Wed Aug 05, 2015 12:34 am
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby chrisjx » Thu Aug 06, 2015 9:54 am

We used the UPS-2 with the U3 and it worked for at least 4 hours on batteries. Great balance of performance and power requirements.

I would say the XU4 is not a replacement but a different device. Different footprint (I have to design new 3D bracket), different bulky HDMI, no micro usb, no I/O port to UPS, double power requirement, no UPS...

Not a replacement. Different footprint and double power might make it unusable for us. We might have to go to lower performance device of the C1. It still has a UPS.

Curious to know how much warning there was of the impending cutoff of the U3? Did I miss the warnings that production would end? Seems like it was 6 days ago; it was announced July 30th. Done. We would have bought 20 sets, maybe more if we had known they we going to disappear.

Very sad.
chrisjx
 
Posts: 9
Joined: Tue Feb 25, 2014 3:21 am
languages_spoken: english
ODROIDs: U3, C1

Re: Battery Power for xu4?

Unread postby phaseshifter » Thu Aug 06, 2015 9:58 am

check with other suppliers there may be stock with some of the internet sellers...
phaseshifter
 
Posts: 1467
Joined: Fri May 08, 2015 9:12 am
languages_spoken: english
ODROIDs: opp sys.. ubuntu ..c1+ ..c-2..xu3 ,xu4...
acc`s vu7,c-shell ,uart,hi-fi ,,hi-fi2,,show,w-board,6x16GB emmc`s 3.5 inch touch...other odroid acc`s as well

Re: Battery Power for xu4?

Unread postby chrisjx » Thu Aug 06, 2015 12:54 pm

Thanks, phaseshifter. I wil do that.
chrisjx
 
Posts: 9
Joined: Tue Feb 25, 2014 3:21 am
languages_spoken: english
ODROIDs: U3, C1

Re: Battery Power for xu4?

Unread postby arich57 » Sun Aug 09, 2015 10:56 pm

I measured amperage during start up with a smart-power to be a max of 2.2 between several boot ups. That was with nothing plugged into UX4 other than sd card.

Just wanted to let people know who are looking for battery solutions, you definitely need at least a 3amp source to be safe.
arich57
 
Posts: 2
Joined: Wed Aug 05, 2015 12:34 am
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby buba013 » Tue Oct 27, 2015 4:58 am

This seems to work http://www.amazon.com/Kingneonlux-QIDIA ... B00U12OG9S ( use the m port)

I have cloud-shell running so lcd powered up my wifi hostspot works and my now portable Plex server for the kids is working .
buba013
 
Posts: 4
Joined: Mon Aug 24, 2015 3:41 pm
languages_spoken: english
ODROIDs: Odroid-xu4

Re: Battery Power for xu4?

Unread postby emanpuedam » Wed Dec 16, 2015 7:06 am

Battery Power for the XU4 Solved! I am Powering my XU4 with a Small Li-Ion Battery Pack
Instructions and Links to Required Parts Listed Below:


It is possible to power an XU4 with a battery system. It took me a few weeks and a lot of trial and error, but I am now powering a XU4 running Ubuntu 15.04 with a battery. All of the components were purchased on Amazon and the entire system should only cost +/- $50. Some basic electronics skills are required to connect the components. If there is anyone who is determined to complete this project in spite of being a complete noob when it comes to electronics. Contact me and I will take the time to write up a step by step, foolproof guide to building a replica of my system.

The Problem:
The XU4 requires 5 volts (power supplied from a USB) however it also requires up to 4 amps. USB ports only provide 2 amps and the most you can hope for from a USB battery charger is 3 amps from a single port. Therefore, none of the USB battery power supplies are an option. There are now battery power packs that provide an AC outlet, however they are bulky, expensive and it would be inefficient to use the XU4's wall transformer.

The Solution.
Since no USB battery power pack will provide sufficient amps, you will need to use a voltage transformer and a battery power pack that can supply it's required input voltage.

I purchased all of the components I used on Amazon (links included).

First you will need to find a voltage transformer. I picked the DROK 12v/24v to 5v/5a 25w Converter. This item is cheap, well reviewed, water proof and has a 90% conversion efficiency rate. It also accepts 12v to 24v as input, allowing a wide range of sources to be used as power sources. It may turn out you already have a device you can utilize and save some money.

If you don't already have a suitable battery power pack, my I recommend the unit i finally settled on TalentCell Rechargeable Li-Ion Battery Pack. This unit utilizes a Li-Ion battery pack, making it lightweight and small enough for easy transport. It should provide power to the XU4 for multiple hours when fully charged. It also has a USB power output that can be used at the same time as the 12v output. If you plan to run a lot of peripheral devices with your XU4, this outlet can be used to power some of the devices, relieving the strain on the main power source.

Once you have these two units, it is a relatively simple matter of connecting the 12v output of the TalentCell (a 5.5mm barrel plug) to the DROK's input and then attaching a second 5.5mm barrel plug to the DROK's output so it can be plugged into the XU4.

That is all it takes to provide battery power to your XU4.

If you have absolutely no experience working with electronics, I urge you to seek out someone who does. A simple mistake such as reversing the polarity of a plug (switching pos. and neg.) could cause irreparable damage to the converter and or your XU4! I would recommend that you own and are comfortable with a soldering iron and a test meter before undertaking this project.

I am more than happy to help in any way I can. If enough people express interest, I would be willing to construct and sell at cost + S/H a pre-fabed kit (including DROK coverter) that would connect the TalentCell directly to an XU4. Please let me know if you are interested. vectorfield@worker.com
emanpuedam
 
Posts: 2
Joined: Wed Dec 16, 2015 6:23 am
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby jacky » Sun Jan 10, 2016 1:18 am

Hey,

Think that by using these cables:
http://www.amazon.com/Power-Enhancer-Fe ... le+femelle
http://www.amazon.com/niceeshop-Barrel- ... +%2F+2.1mm

And connect 2 usb on this battery
http://www.amazon.com/Upgraded-Capacity ... r+16750mAh
on 2.1A and 2.4A.

It should also work?
jacky
 
Posts: 4
Joined: Sun Jan 10, 2016 1:04 am
languages_spoken: english

Re: Battery Power for xu4?

Unread postby phaseshifter » Sun Jan 10, 2016 2:25 am

16,75 a/h battery will run it u will need the barrel to usb cable
so battery ==>usb to barrell connector==>xu4..
http://www.amazon.com/niceeshop-Barrel- ... +%2F+2.1mm............use this cable for the powering of the xu4
should run it for a few hours how long will depend on load and remember you can really only use 75% of the battery capacity..or you will destroy it rapidly.
.so good for approx 3-4 hours i would think..maybe more..its hard to determine exactly..
phaseshifter
 
Posts: 1467
Joined: Fri May 08, 2015 9:12 am
languages_spoken: english
ODROIDs: opp sys.. ubuntu ..c1+ ..c-2..xu3 ,xu4...
acc`s vu7,c-shell ,uart,hi-fi ,,hi-fi2,,show,w-board,6x16GB emmc`s 3.5 inch touch...other odroid acc`s as well

Re: Battery Power for xu4?

Unread postby vanja » Sun Jan 24, 2016 2:02 am

jacky wrote:Hey,

Think that by using these cables:
http://www.amazon.com/Power-Enhancer-Fe ... le+femelle
http://www.amazon.com/niceeshop-Barrel- ... +%2F+2.1mm

And connect 2 usb on this battery
http://www.amazon.com/Upgraded-Capacity ... r+16750mAh
on 2.1A and 2.4A.

It should also work?


hi jacky,

is this a solution you are using or just plan to use?

cause it is most simple+cheap ($32, 11.3oz, featuring a 4.5A total output capable of simultaneously charging 2 tablets)

another candidates from amazon
* http://www.amazon.com/Upgraded-Capacity ... B00M3073L4 ($50, 15.8oz, 3 amps per port or 4 amps through three ports)
* http://www.amazon.com/EasyAcc-20000mAh- ... B01422TC14 ($35, 16 oz, up to 2.4A per port, 4.8A Output)

please share any experience with power banks for xu-4

regards,
Vanja
vanja
 
Posts: 1
Joined: Tue Jan 05, 2016 7:21 am
Location: Izmir, Turkey
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby jacky » Mon Feb 01, 2016 11:19 pm

vanja wrote:
jacky wrote:Hey,

Think that by using these cables:
http://www.amazon.com/Power-Enhancer-Fe ... le+femelle
http://www.amazon.com/niceeshop-Barrel- ... +%2F+2.1mm

And connect 2 usb on this battery
http://www.amazon.com/Upgraded-Capacity ... r+16750mAh
on 2.1A and 2.4A.

It should also work?


hi jacky,

is this a solution you are using or just plan to use?

cause it is most simple+cheap ($32, 11.3oz, featuring a 4.5A total output capable of simultaneously charging 2 tablets)

another candidates from amazon
* http://www.amazon.com/Upgraded-Capacity ... B00M3073L4 ($50, 15.8oz, 3 amps per port or 4 amps through three ports)
* http://www.amazon.com/EasyAcc-20000mAh- ... B01422TC14 ($35, 16 oz, up to 2.4A per port, 4.8A Output)

please share any experience with power banks for xu-4

regards,
Vanja


Hi vanja ,

I just received the battery but my Odroid won't boot while the battery is plugged to it.

Everything works fine with my Raspberry for 8 hours.

I'm waiting for this : http://www.amazon.fr/gp/product/B019IL6 ... TE_3p_dp_1
to try and understand what's wrong.

Does anybody know what could be wrong ?
jacky
 
Posts: 4
Joined: Sun Jan 10, 2016 1:04 am
languages_spoken: english

Re: Battery Power for xu4?

Unread postby odroid » Tue Feb 02, 2016 9:33 am

Need to measure the output voltage of the battery when you turn on the XU4 with a DMM.
I think the In-rush current of XU4 could be 2~3 times higher than RPI.
User avatar
odroid
Site Admin
 
Posts: 21796
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID

Re: Battery Power for xu4?

Unread postby Respectech » Wed Feb 03, 2016 5:44 am

I was hoping to find a good solution from the suggestions above, but most of the links above are either 404 or not in stock. There are a couple that seem to be promising, but kind of expensive.

ameriDroid has a DC-DC converter with more than enough capacity at http://ameridroid.com/products/dc-dc-12 ... -converter on sale for $9.22! So you can use any rechargeable battery pack at any voltage between 5VDC and 30VDC to power your XU4. Great for using the XU4 as a car-puter.
Respectech
 
Posts: 279
Joined: Wed Nov 13, 2013 9:20 am
Location: California
languages_spoken: English, German, some Ukrainian, some Spanish
ODROIDs: All the ODROIDs!!

Well, the ones released since the U2.

Re: Battery Power for xu4?

Unread postby venkatbo » Wed Feb 03, 2016 7:50 am

Respectech wrote:... ameriDroid has a DC-DC converter with more than enough capacity at http://ameridroid.com/products/dc-dc-12 ... -converter on sale for $9.22! So you can use any rechargeable battery pack at any voltage between 5VDC and 30VDC to power your XU4. Great for using the XU4 as a car-puter.

Nice accessory @Respectech.
Have a question for you. I have 3 XU4's in my lab and I was wondering if it would be safe (over-current usage protection, etc) to use one of these to provide 5V/4A for each of the 3 XU4's. If that is safe to do so, do you have any recommendations for a psu whose output can be used for the input side of this accessory ?

thanks.
User avatar
venkatbo
 
Posts: 423
Joined: Mon Feb 25, 2013 3:10 pm
Location: Bay Area, California
languages_spoken: english
ODROIDs: C0/C1+/C2 U3+ XU3-Lite/XU4 VU/VU7+ Touchscreen Show TFT Cloudshell SmartPower mAHRS DAC GPS Multiscope

Re: Battery Power for xu4?

Unread postby Cancerian » Thu Feb 04, 2016 4:21 am

jl303 wrote:I also found a portable battery that delivers 5v/4a through one usb port. It's called Anker 2nd Gen Astro3.
http://www.ianker.com/product/79AN7904S-B2A
I exchanged with Anker support, and they said it can deliver up to 4a through one usb port or combined. They sell many different batteries but they said this is the only battery that can do it so far.
I just received the battery and a usb to 5.5mm cable.
I just plugged it in with no soldering and no modification, and it seems working fine.


I just found the Anker PowerCore 20100, which says that it can deliver 5v/4.8a through any combination of ports, but one of Anker's support representatives indicated that they have no battery that can deliver 4a through a single port, and that even the Astro3 only delivers up to 2.4a through each port, or 3a in the case of USB type C ports. After speaking with the representative, I came away with the feeling that I would burn out some of the electronics or hit an overload protection feature of the battery if I made the attempt to connect any of their batteries to an XU4 and experienced high load conditions or had peripherals connected to the XU4's USB ports. @jl303, have you experienced any issues with the Astro3, and if not, do you think the newer PowerCore 20100 would also work under similar conditions? I really like this battery if it can work with the USB to type M barrel above, as it has a battery capacity of 20100 mAH, which is much higher than the 12800 mAH capacity of the Astro3, and the current price of the PowerCore 20100 is lower than the price I see on Amazon for the Astro3 by $40 USD. Has anyone else used either of these battery systems to power an XU4, and if so, what problems did you face while using it?
Cancerian
 
Posts: 1
Joined: Thu Jan 14, 2016 11:09 am
Location: Planet Earth
languages_spoken: english
ODROIDs: XU4, C2

Re: Battery Power for xu4?

Unread postby Respectech » Thu Feb 04, 2016 9:43 am

venkatbo wrote:Nice accessory @Respectech.
Have a question for you. I have 3 XU4's in my lab and I was wondering if it would be safe (over-current usage protection, etc) to use one of these to provide 5V/4A for each of the 3 XU4's. If that is safe to do so, do you have any recommendations for a psu whose output can be used for the input side of this accessory ?

thanks.


Let's see if the converter can do the trick via some math. The specs state it is 95% efficient, and can supply up to 12A on the output, so that should be able to power 3 XU4's at full utilization (4A * 3). If you were using a 12VDC input power supply, this means that the 12VDC power supply would need to be able to supply 12A * (5VDC / 12VDC) / .95 = 5.27A@12VDC. I did a quick search in my PSU drawer and found a couple of 12VDC/3.3A power supplies, so those would be a bit too small. The 12VDC/3.3A PSU would be enough to run 2 XU4's almost certainly, or 3 at an average of 2.5A being pulled at any one time by all 3. I think that's reasonable, but it sounds like an experiment would be needed to verify.

I hope this helps!
Respectech
 
Posts: 279
Joined: Wed Nov 13, 2013 9:20 am
Location: California
languages_spoken: English, German, some Ukrainian, some Spanish
ODROIDs: All the ODROIDs!!

Well, the ones released since the U2.

Re: Battery Power for xu4?

Unread postby dronus » Fri Apr 29, 2016 3:25 am

As for many applications that are mostly idling, the largest power draw will be while booting.
Maybe it's possible to have a reduced clocking early, or delay the activation off some devices to later, to reduce the peak draw on bootup?
For example, if the cpu clock would be lowered from the beginning, PHY and HDMI stay disabled until the end off the boot when they could be activated if the desktop is already up and idling.
dronus
 
Posts: 80
Joined: Fri Jul 25, 2014 7:24 pm
languages_spoken: english
ODROIDs: U3, XU4, C1+

Re: Battery Power for xu4?

Unread postby DarkBahamut » Sat Apr 30, 2016 8:15 pm

I'm not sure about disabling other devices, but limiting the booting clockspeeds should be possible.

You need to compile a kernel with the following change.

File in question is drivers/cpufreq/exynos5422-eagle-cpufreq.c

Lines 661 and 662 set the A15 booting frequency.

Code: Select all
   info->boot_cpu_min_qos = exynos5422_freq_table_CA15[L9].frequency;
   info->boot_cpu_max_qos = exynos5422_freq_table_CA15[L9].frequency;


L9 = 1.5GHz. You could try L15 maybe (900MHz) and see if that helps. I've not tried it so no promises though. Should look like this after.

Code: Select all
   info->boot_cpu_min_qos = exynos5422_freq_table_CA15[L15].frequency;
   info->boot_cpu_max_qos = exynos5422_freq_table_CA15[L15].frequency;
DarkBahamut
 
Posts: 202
Joined: Tue Jan 19, 2016 10:19 am
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby dronus » Tue May 03, 2016 9:20 am

I found an easy solution not requiring kernel changes: Just adding maxcpus=2 to the kernel command line in boot.ini drops the bootup power usage to 4W.

Individual CPUs can later be reenabled according to the available power by writing 1 to the /sys/devices/system/cpu/cpuX/online files.

This way the XU4 can boot and run stable from an 2A power bank.
dronus
 
Posts: 80
Joined: Fri Jul 25, 2014 7:24 pm
languages_spoken: english
ODROIDs: U3, XU4, C1+

Re: Battery Power for xu4?

Unread postby mad_ady » Tue May 03, 2016 4:35 pm

This information needs to make its way on a wiki page :)
User avatar
mad_ady
 
Posts: 1434
Joined: Wed Jul 15, 2015 5:00 pm
Location: Bucharest, Romania
languages_spoken: english
ODROIDs: XU3, C1+, C2

Re: Battery Power for xu4?

Unread postby odroid » Tue May 03, 2016 4:54 pm

mad_ady wrote:This information needs to make its way on a wiki page :)


Good idea. I added a link with a credit to dronus ;)
http://odroid.com/dokuwiki/doku.php?id= ... eripherals
User avatar
odroid
Site Admin
 
Posts: 21796
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID

Re: Battery Power for xu4?

Unread postby dronus » Fri May 13, 2016 7:39 pm

You may drop the credit, but maybe do a real wiki page or section instead :-)

Clicking the link is confusing, as there are several other working solutions here.

The page may mention the hardware (eg. selfmade Li-Ion circuits) and software solutions (like mine, using a power bank and adjusting the software).
dronus
 
Posts: 80
Joined: Fri Jul 25, 2014 7:24 pm
languages_spoken: english
ODROIDs: U3, XU4, C1+

Re: Battery Power for xu4?

Unread postby odroid » Mon May 16, 2016 9:46 pm

@dronus,

Can you show us the result of below commands when "maxcpus=2" was added in the kernel parameter?
One user reported the "maxcpus=2" didn't work well.
Code: Select all
cat /sys/devices/system/cpu/cpu0/online
cat /sys/devices/system/cpu/cpu1/online
cat /sys/devices/system/cpu/cpu2/online
cat /sys/devices/system/cpu/cpu3/online
cat /sys/devices/system/cpu/cpu4/online
cat /sys/devices/system/cpu/cpu5/online
cat /sys/devices/system/cpu/cpu6/online
cat /sys/devices/system/cpu/cpu7/online
User avatar
odroid
Site Admin
 
Posts: 21796
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID

Re: Battery Power for xu4?

Unread postby ard » Fri May 20, 2016 9:48 pm

I just compile the kernel with the powersafe governer. Once the boot reaches X11 I put in the right frequencies and switch to performance governer.
I normally use 1.4GHz for the cpu's as that limits it's peaks to 7W or less.
I've tried turning off cpu's and later turn them on again, but you have to reroute irq's when you turn on cpu's. But I will definetely try that.
As for power usage: https://www.youtube.com/watch?v=SVSActfqXlQ shows quake2webgl on chromium and the last few seconds show the smart psu, with lower than 1A power usage.
ard
 
Posts: 44
Joined: Tue Jul 09, 2013 2:12 am
languages_spoken: english, dutch, german
ODROIDs: ODROID-U2

Re: Battery Power for xu4?

Unread postby odroid » Sat May 21, 2016 10:26 am

Thank you for the detail explanation as well as the video.
Quite impressive the low power consumption while running the webgl application. :o
User avatar
odroid
Site Admin
 
Posts: 21796
Joined: Fri Feb 22, 2013 11:14 pm
languages_spoken: English
ODROIDs: ODROID

Re: Battery Power for xu4?

Unread postby ronaldlees » Fri Jul 08, 2016 12:02 am

Respectech wrote:I was hoping to find a good solution from the suggestions above, but most of the links above are either 404 or not in stock. There are a couple that seem to be promising, but kind of expensive.

ameriDroid has a DC-DC converter with more than enough capacity at http://ameridroid.com/products/dc-dc-12 ... -converter on sale for $9.22! So you can use any rechargeable battery pack at any voltage between 5VDC and 30VDC to power your XU4. Great for using the XU4 as a car-puter.


That price is a couple dollars cheaper than I've seen for similar supplies on Amazon, so thanks for the link!

I learned to love this type of supply because I needed to use large LCD screens with SBC boards. One thing I found about these types of supplies is that I needed to exercise the potentiometer before first use. Without any load attached, I take a screwdriver and turn it through most of its travel, one way then the other, while staying within the voltage specs (using a voltmeter to monitor). Probably, it wouldn't hurt to spin the pot a few times before anything is attached, remembering the number of turns, and returning to the original position (which should be, but may not be, minimum voltage level). After exercising the pot, I just set it to the desired voltage (usually 5 VDC). This is not advice, but it works for me! Caveat Emptor! I have found that the position of the potentiometer (initial setting), out of the box, is pretty random. Most of these supplies are "counter-clockwise = lower voltage," but that's not true of all of them.

If I don't "exercise" the potentiometer, it can have little burs inside of it, or "filiments" - which can cause erratic output. It's only my guess that there are filiments inside new pots, because I'm certainly no potentiometer expert. IMO, the exercising, by turning it a few times, helps to minimize this problem, but probably it could still happen. This would seem to be true of any potentiometer controlled supply. So, AFAIK such supplies need a certain "burn-in" procedure. Probably, the exercise should be done with a dummy load of the same current draw as the intended target, prior to actual use. I blew up a nice VU screen because the supply went berserk and put over 12 VDC to it! It wasn't the Ameridroid supply, but another brand of the same general build. Better safe than sorry!
User avatar
ronaldlees
 
Posts: 82
Joined: Sat Mar 29, 2014 3:52 am
languages_spoken: english
ODROIDs: Odroid C1
Odroid C1+
Odroid XU4

Re: Battery Power for xu4?

Unread postby ronaldlees » Fri Jul 08, 2016 12:40 am

The whole potentiometer problem would seem to say it's better to have a fixed output supply, if one can live with the non-flexibility.
User avatar
ronaldlees
 
Posts: 82
Joined: Sat Mar 29, 2014 3:52 am
languages_spoken: english
ODROIDs: Odroid C1
Odroid C1+
Odroid XU4

Re: Battery Power for xu4?

Unread postby Rushlight » Wed Aug 10, 2016 6:03 pm

for 60-100$ Bestbuy sells battery packs that can output 3.0-4.5A though 1-2 USB ports,some are over 10000mA. it's not super powerful, however, if you're shrewd you can find a really cheap one, buy a few, and hook the batteries up in series off one board :3
:3
Rushlight
 
Posts: 51
Joined: Mon Jun 06, 2016 3:15 pm
languages_spoken: English
ODROIDs: C-0(1)
C-0(2)
16GB-EMMC

RPI3B

Re: Battery Power for xu4?

Unread postby nmshaikh » Thu Dec 22, 2016 6:46 pm

Respectech wrote: ...ameriDroid has a DC-DC converter with more than enough capacity at http://ameridroid.com/products/dc-dc-12 ... -converter on sale for $9.22! So you can use any rechargeable battery pack at any voltage between 5VDC and 30VDC to power your XU4. Great for using the XU4 as a car-puter.


Hi guys, this is my first time posting on this forum. I bought my Odroid XU-4 board in mid November this year and I am using it for a robotics project to control a small autonomous car. I needed to power my board while it is on the car and I have developed a solution similar to the one mentioned by Respectech by using a cheap adjustable output voltage regulator that regulates the input voltage from the car battery from 7.2 volts to the 5 volts needed by the XU-4.

All you need is a voltage regulator, a couple of capacitors, and a couple of resistors to solder the circuit yourself. The particular voltage regulator I have used is the LD1084v by ST Microelectronics. This is a low dropout voltage regulator that can take between 6.5 VDC to 30 VDC as input to give an output of 5 VDC at 5 Amps. I have attached the circuit schematics for the regulator. All you need is 2 capacitors at 10 uF, 1 resistor at 120 ohms, and 1 resistor at 365 ohms to complete the circuit (I have also used a metal heatsink just in case. I am not sure how heated up the voltage regulator will get). I have attached another image showing the XU-4 board hooked up to the car battery and my laptop screen after the voltage is regulated. The cost of all the components was around 15 Malaysian Ringgits (about 3.5 US dollars!)

Feel free to ask me about any additional information. I am happy to help :D

Circuit Schematics.JPG
Schematics for voltage regulator circuit
Circuit Schematics.JPG (33.11 KiB) Viewed 2394 times

15696703_10211728347829787_1027034741_o.jpg
XU-4 powered by a 7.2 volts 2000mAh battery
15696703_10211728347829787_1027034741_o.jpg (179.12 KiB) Viewed 2394 times
Attachments
en.CD00003086.pdf
Datasheet for the LD1084v Voltage regulator
(531.18 KiB) Downloaded 49 times
nmshaikh
 
Posts: 4
Joined: Thu Oct 27, 2016 6:06 pm
languages_spoken: English, Urdu

Re: Battery Power for xu4?

Unread postby hommsy » Fri Feb 10, 2017 12:30 am

Does anyone have the issue where the XU4 keeps restarting at boot when connected to battery?

It seems to me that when the current draw reaches around 3A, the XU4 reboots (or maybe loses power and starts up again)

Anyone faced this issue? Anyone has a fix?

setup:
2 LiPo batteries 4S 14.8V 6.6Ah connected in parallel
1 Turnigy SBEC step down converter (step down to 5V and max 5A)
hommsy
 
Posts: 11
Joined: Thu Feb 09, 2017 7:00 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby mad_ady » Fri Feb 10, 2017 5:01 am

To reduce startup current demands you can boot with only the little cores and manually switch on the big cores as needed. Add numcpus=2 (or 4) to bootargs in boot.ini
User avatar
mad_ady
 
Posts: 1434
Joined: Wed Jul 15, 2015 5:00 pm
Location: Bucharest, Romania
languages_spoken: english
ODROIDs: XU3, C1+, C2

Re: Battery Power for xu4?

Unread postby Zeroth » Fri Feb 10, 2017 8:33 am

Hi everyone,

Is the conclusion to this thread that there is no easy way to power the XU4 by battery? By "easy" I guess I mean... No way without soldering stuff together? (I'm not very good at that and tend to break things when I try). I was hoping for a set-up with some kind of battery pack / power bank and some adapter cables but it looks like that may not be possible?

Cheers,

Jonty
Zeroth
 
Posts: 12
Joined: Thu Feb 09, 2017 7:28 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby rooted » Fri Feb 10, 2017 8:41 am

Zeroth wrote:Hi everyone,

Is the conclusion to this thread that there is no easy way to power the XU4 by battery? By "easy" I guess I mean... No way without soldering stuff together? (I'm not very good at that and tend to break things when I try). I was hoping for a set-up with some kind of battery pack / power bank and some adapter cables but it looks like that may not be possible?

Cheers,

Jonty

A power bank would be okay if it has 4A USB output.
User avatar
rooted
 
Posts: 3287
Joined: Fri Dec 19, 2014 9:12 am
Location: Gulf of Mexico, US
languages_spoken: english
ODROIDs: C1
C1+
C2
XU3 Lite
XU4
VU7+
HiFi Shield 2
Smart Power (original)

Re: Battery Power for xu4?

Unread postby Zeroth » Fri Feb 10, 2017 7:26 pm

rooted wrote:A power bank would be okay if it has 4A USB output.

Hi, thanks for the help. I read that each USB port only goes up to around 2A? So do I have to combine the output from multiple USB ports somehow?
Zeroth
 
Posts: 12
Joined: Thu Feb 09, 2017 7:28 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby hommsy » Fri Feb 10, 2017 8:55 pm

Zeroth wrote:
rooted wrote:A power bank would be okay if it has 4A USB output.

Hi, thanks for the help. I read that each USB port only goes up to around 2A? So do I have to combine the output from multiple USB ports somehow?


Yea you could combine batteries. What im doing now is connecting 2 LiPo batteries in parallel, the oputput of those goes to a step dpwn converter which then goes to the xu4. This should work (will confirm this method by tomorrow)

battery: https://hobbyking.com/en_us/multistar-h ... -pack.html
converter: https://hobbyking.com/en_us/turnigy-5a- ... -lipo.html
hommsy
 
Posts: 11
Joined: Thu Feb 09, 2017 7:00 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby Zeroth » Sat Feb 11, 2017 12:10 am

Thanks hommsy. I'm not to good with electronics so sorry for any stupid questions... How have you attached this set-up to the correct 5.5mm power input? Also how long battery life do you expect and is there enough current to support an external hard drive connected to the XU4?
Zeroth
 
Posts: 12
Joined: Thu Feb 09, 2017 7:28 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby hommsy » Sat Feb 11, 2017 7:44 pm

mad_ady wrote:To reduce startup current demands you can boot with only the little cores and manually switch on the big cores as needed. Add numcpus=2 (or 4) to bootargs in boot.ini


and sounds like a good plan for booting but what happens after that? in other words, when switch back to all cores after boot, wont the xu4 disconnect again because of insufficient power? have you tried this?
hommsy
 
Posts: 11
Joined: Thu Feb 09, 2017 7:00 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby hommsy » Sat Feb 11, 2017 8:51 pm

mad_ady wrote:To reduce startup current demands you can boot with only the little cores and manually switch on the big cores as needed. Add numcpus=2 (or 4) to bootargs in boot.ini



just a small correction for future reference, its maxcpus=2 not numcpus=2
hommsy
 
Posts: 11
Joined: Thu Feb 09, 2017 7:00 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby mad_ady » Sun Feb 12, 2017 2:05 pm

Right, sorry for my mistake. The point is that on boot all cores will be busy and the startup current exceeds 2A. After startup is done you can enable all cores and the system should be stable as long as the load is light and doesn't exceed 2A. It will crash if you go above 2A though.
User avatar
mad_ady
 
Posts: 1434
Joined: Wed Jul 15, 2015 5:00 pm
Location: Bucharest, Romania
languages_spoken: english
ODROIDs: XU3, C1+, C2

Re: Battery Power for xu4?

Unread postby Zeroth » Mon Feb 13, 2017 8:52 pm

Hi hommsy, did you manage to get that set-up working?
Zeroth
 
Posts: 12
Joined: Thu Feb 09, 2017 7:28 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby hommsy » Wed Feb 15, 2017 7:06 pm

Zeroth wrote:Hi hommsy, did you manage to get that set-up working?


Yea it finally works. No need to reduce the number of CPU's either.

You will need a battery, something like this https://www.amazon.com/Floureon-Battery ... tery&psc=1
[in battery choosing, make sure its not rated as 10C and make sure the mAh is enough for your application]

and then you will need a step-down DC-DC converter (or BEC), something like this https://www.amazon.com/FVT-Adjustable-U ... ds=ubec+6a
[make sure that the output is 5v and the current is at least 5A ]

and thats it..well of course you will need some connectors, plugs and soldering..
hommsy
 
Posts: 11
Joined: Thu Feb 09, 2017 7:00 pm
languages_spoken: english
ODROIDs: XU4

Re: Battery Power for xu4?

Unread postby Zeroth » Fri Feb 17, 2017 6:49 am

Great, thanks for the help :)
Zeroth
 
Posts: 12
Joined: Thu Feb 09, 2017 7:28 pm
languages_spoken: english
ODROIDs: XU4


Return to Hardware and peripherals

Who is online

Users browsing this forum: No registered users and 3 guests